[PATCH] arm64: Add support for bigger u-boot when CONFIG_POSITION_INDEPENDENT=y

[Stephen Warren]

On 9/3/20 1:07 PM, Edgar E. Iglesias wrote:
> On Thu, Sep 03, 2020 at 09:45:39AM -0600, Stephen Warren wrote:
>> On 9/3/20 7:40 AM, André Przywara wrote:
>>> On 03/09/2020 14:35, Michal Simek wrote:
>>>>
>>>>
>>>> On 02. 09. 20 18:34, Stephen Warren wrote:
>>>>> On 9/2/20 5:15 AM, Michal Simek wrote:
>>>>>> From: "Edgar E. Iglesias" <edgar.iglesias at xilinx.com>
>>>>>>
>>>>>> When U-Boot binary exceeds 1MB with CONFIG_POSITION_INDEPENDENT=y
>>>>>> compilation error is shown:
>>>>>> /mnt/disk/u-boot/arch/arm/cpu/armv8/start.S:71:(.text+0x3c): relocation
>>>>>> truncated to fit: R_AARCH64_ADR_PREL_LO21 against symbol `__rel_dyn_end'
>>>>>> defined in .bss_start section in u-boot.
>>>>>>
>>>>>> It is caused by adr instruction which permits the calculation of any byte
>>>>>> address within +- 1MB of the current PC.
>>>>>> Because U-Boot is bigger then 1MB calculation is failing.
>>>>>>
>>>>>> The patch is using adrp/add instructions where adrp shifts a signed, 21-bit
>>>>>> immediate left by 12 bits (4k page), adds it to the value of the program
>>>>>> counter with the bottom 12 bits cleared to zero. Then add instruction
>>>>>> provides the lower 12 bits which is offset within 4k page.
>>>>>> These two instructions together compose full 32bit offset which should be
>>>>>> more then enough to cover the whole u-boot size.
>>>>>
>>>>>> diff --git a/arch/arm/cpu/armv8/start.S b/arch/arm/cpu/armv8/start.S
>>>>>
>>>>>> @@ -67,8 +67,10 @@ pie_fixup:
>>>>>>  	adr	x0, _start		/* x0 <- Runtime value of _start */
>>>>>>  	ldr	x1, _TEXT_BASE		/* x1 <- Linked value of _start */
>>>>>>  	sub	x9, x0, x1		/* x9 <- Run-vs-link offset */
>>>>>> -	adr	x2, __rel_dyn_start	/* x2 <- Runtime &__rel_dyn_start */
>>>>>> -	adr	x3, __rel_dyn_end	/* x3 <- Runtime &__rel_dyn_end */
>>>>>> +	adrp    x2, __rel_dyn_start     /* x2 <- Runtime &__rel_dyn_start */
>>>>>> +	add     x2, x2, #:lo12:__rel_dyn_start
>>>>>> +	adrp    x3, __rel_dyn_end       /* x3 <- Runtime &__rel_dyn_end */
>>>>>> +	add     x3, x3, #:lo12:__rel_dyn_end
>>>>>>  pie_fix_loop:
>>>>>>  	ldp	x0, x1, [x2], #16	/* (x0, x1) <- (Link location, fixup) */
>>>>>>  	ldr	x4, [x2], #8		/* x4 <- addend */
>>>>>
>>>>> There are likely a bunch of other places in the code that need updating
>>>>> too; take a look at commit 49e93875a62f "arm64: support running at addr
>>>>> other than linked to" (which introduced the code above) to find other
>>>>> places with similar instruction sequences that almost certainly need
>>>>> updating.
>>>>>
>>>>
>>>> I didn't hit any issue to have a need to update them. Definitely worth
>>>> to check that locations too.
>>>
>>> So I thought the same, so I checked at least this file. And while there
>>> are other "adr" instructions, they only go to nearby labels, so don't
>>> need to be pumped up.
>>> But I will try to grep for more cases as well.
>>
>>
>> So in the patch I linked to, what about the added ard instructions in
>> arch/arm/lib/crt0_64.S and arch/arm/lib/relocate_64.S?
>>
>> Perhaps that code gets linked more towards the middle of U-Boot than the
>> code you're fixing in start.S, so the max 1M offset just happens to
>> reach all the relevant symbols and relocations that are in your current
>> binary, but if your binary gets a little larger (e.g. goes from 1.05M to
>> 2M say) that code will fail in the same way?
> 
> Yes, those were apparently already corrected by Ibai:
> https://github.com/u-boot/u-boot/commit/98ffbb78e12646a1d06236ad6a1893217f255aae#diff-4f864f65dc6b6f2535a5d252b7c9fcc7

Ah OK.

So I guess this means that in practice, U-Boot already has the
limitation that the load (and relocation target?) address must be
4K-aligned, since it uses the same instruction sequence we're
discusssing here.