[PATCH v3 8/8] IPQ40xx: Add USB nodes

Robert Marko robert.marko at sartura.hr
Thu Sep 10 16:00:06 CEST 2020


There are drivers to support built in USB controller and PHY-s now, so lets add the USB nodes to DTSI.

Signed-off-by: Robert Marko <robert.marko at sartura.hr>
Cc: Luka Perkov <luka.perkov at sartura.hr>
---
 arch/arm/dts/qcom-ipq4019.dtsi | 76 ++++++++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/arch/arm/dts/qcom-ipq4019.dtsi b/arch/arm/dts/qcom-ipq4019.dtsi
index 7b15df38d8..e0e4188e5d 100644
--- a/arch/arm/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/dts/qcom-ipq4019.dtsi
@@ -90,5 +90,81 @@
 			gpio-bank-name="soc";
 			#gpio-cells = <2>;
 		};
+
+		usb3_ss_phy: ssphy at 9a000 {
+			compatible = "qcom,usb-ss-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0x9a000 0x800>;
+			reg-names = "phy_base";
+			resets = <&reset USB3_UNIPHY_PHY_ARES>;
+			reset-names = "por_rst";
+			status = "disabled";
+		};
+
+		usb3_hs_phy: hsphy at a6000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa6000 0x40>;
+			reg-names = "phy_base";
+			resets = <&reset USB3_HSPHY_POR_ARES>, <&reset USB3_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb3: usb3 at 8af8800 {
+			compatible = "qcom,dwc3";
+			reg = <0x8af8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB3_MASTER_CLK>,
+				 <&gcc GCC_USB3_SLEEP_CLK>,
+				 <&gcc GCC_USB3_MOCK_UTMI_CLK>;
+			clock-names = "master", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			dwc3 at 8a00000 {
+				compatible = "snps,dwc3";
+				reg = <0x8a00000 0xf8000>;
+				phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				maximum-speed = "super-speed";
+				snps,dis_u2_susphy_quirk;
+			};
+		};
+
+		usb2_hs_phy: hsphy at a8000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa8000 0x40>;
+			reg-names = "phy_base";
+			resets = <&reset USB2_HSPHY_POR_ARES>, <&reset USB2_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb2: usb2 at 60f8800 {
+			compatible = "qcom,dwc3";
+			reg = <0x60f8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB2_MASTER_CLK>,
+				 <&gcc GCC_USB2_SLEEP_CLK>,
+				 <&gcc GCC_USB2_MOCK_UTMI_CLK>;
+			clock-names = "master", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			dwc3 at 6000000 {
+				compatible = "snps,dwc3";
+				reg = <0x6000000 0xf8000>;
+				phys = <&usb2_hs_phy>;
+				phy-names = "usb2-phy";
+				dr_mode = "host";
+				maximum-speed = "high-speed";
+				snps,dis_u2_susphy_quirk;
+			};
+		};
 	};
 };
-- 
2.26.2



More information about the U-Boot mailing list