[PATCH v2 3/4] usb: xhci-dwc3: Add support for clocks/resets

Andre Przywara andre.przywara at arm.com
Wed Apr 21 12:37:00 CEST 2021


On Sat, 17 Apr 2021 09:20:58 -0500
Samuel Holland <samuel at sholland.org> wrote:

> Some platforms, like the Allwinner H6, do not have a separate glue layer
> around the dwc3. Instead, they rely on the clocks/resets/phys referenced
> from the dwc3 DT node itself. Add support for enabling the clocks/resets
> referenced from the dwc3 DT node.
> 
> Signed-off-by: Samuel Holland <samuel at sholland.org>

Looks good, and even if they are redundancies with the other kind of
binding, it should not hurt to have it in, to cover our DTs.

Reviewed-by: Andre Przywara <andre.przywara at arm.com>

Cheers,
Andre

> ---
>  drivers/usb/host/xhci-dwc3.c | 56 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/drivers/usb/host/xhci-dwc3.c b/drivers/usb/host/xhci-dwc3.c
> index 3e0ae80cec..5b12d1358e 100644
> --- a/drivers/usb/host/xhci-dwc3.c
> +++ b/drivers/usb/host/xhci-dwc3.c
> @@ -7,10 +7,12 @@
>   * Author: Ramneek Mehresh<ramneek.mehresh at freescale.com>
>   */
>  
> +#include <clk.h>
>  #include <common.h>
>  #include <dm.h>
>  #include <generic-phy.h>
>  #include <log.h>
> +#include <reset.h>
>  #include <usb.h>
>  #include <dwc3-uboot.h>
>  #include <linux/delay.h>
> @@ -21,7 +23,9 @@
>  #include <linux/usb/otg.h>
>  
>  struct xhci_dwc3_plat {
> +	struct clk_bulk clks;
>  	struct phy_bulk phys;
> +	struct reset_ctl_bulk resets;
>  };
>  
>  void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
> @@ -111,6 +115,46 @@ void dwc3_set_fladj(struct dwc3 *dwc3_reg, u32 val)
>  }
>  
>  #if CONFIG_IS_ENABLED(DM_USB)
> +static int xhci_dwc3_reset_init(struct udevice *dev,
> +				struct xhci_dwc3_plat *plat)
> +{
> +	int ret;
> +
> +	ret = reset_get_bulk(dev, &plat->resets);
> +	if (ret == -ENOTSUPP || ret == -ENOENT)
> +		return 0;
> +	else if (ret)
> +		return ret;
> +
> +	ret = reset_deassert_bulk(&plat->resets);
> +	if (ret) {
> +		reset_release_bulk(&plat->resets);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int xhci_dwc3_clk_init(struct udevice *dev,
> +			      struct xhci_dwc3_plat *plat)
> +{
> +	int ret;
> +
> +	ret = clk_get_bulk(dev, &plat->clks);
> +	if (ret == -ENOSYS || ret == -ENOENT)
> +		return 0;
> +	if (ret)
> +		return ret;
> +
> +	ret = clk_enable_bulk(&plat->clks);
> +	if (ret) {
> +		clk_release_bulk(&plat->clks);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
>  static int xhci_dwc3_probe(struct udevice *dev)
>  {
>  	struct xhci_hcor *hcor;
> @@ -122,6 +166,14 @@ static int xhci_dwc3_probe(struct udevice *dev)
>  	u32 reg;
>  	int ret;
>  
> +	ret = xhci_dwc3_reset_init(dev, plat);
> +	if (ret)
> +		return ret;
> +
> +	ret = xhci_dwc3_clk_init(dev, plat);
> +	if (ret)
> +		return ret;
> +
>  	hccr = (struct xhci_hccr *)((uintptr_t)dev_remap_addr(dev));
>  	hcor = (struct xhci_hcor *)((uintptr_t)hccr +
>  			HC_LENGTH(xhci_readl(&(hccr)->cr_capbase)));
> @@ -171,6 +223,10 @@ static int xhci_dwc3_remove(struct udevice *dev)
>  
>  	dwc3_shutdown_phy(dev, &plat->phys);
>  
> +	clk_release_bulk(&plat->clks);
> +
> +	reset_release_bulk(&plat->resets);
> +
>  	return xhci_deregister(dev);
>  }
>  



More information about the U-Boot mailing list