[PATCH 14/17] arm: dts: k3-am642: Add initial support for EVM

Dave Gerlach d-gerlach at ti.com
Fri Apr 23 18:27:45 CEST 2021


The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.

Add basic support.

Signed-off-by: Dave Gerlach <d-gerlach at ti.com>
---
 arch/arm/dts/Makefile         |   1 +
 arch/arm/dts/k3-am642-evm.dts | 246 ++++++++++++++++++++++++++++++++++
 2 files changed, 247 insertions(+)
 create mode 100644 arch/arm/dts/k3-am642-evm.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index c6710826a0ae..70ba1414fb01 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1002,6 +1002,7 @@ dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
 			      k3-j721e-r5-common-proc-board.dtb \
 			      k3-j7200-common-proc-board.dtb \
 			      k3-j7200-r5-common-proc-board.dtb
+dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb
 
 dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt7622-rfb.dtb \
diff --git a/arch/arm/dts/k3-am642-evm.dts b/arch/arm/dts/k3-am642-evm.dts
new file mode 100644
index 000000000000..1f1787750fef
--- /dev/null
+++ b/arch/arm/dts/k3-am642-evm.dts
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "k3-am642.dtsi"
+
+/ {
+	compatible =  "ti,am642-evm", "ti,am642";
+	model = "Texas Instruments AM642 EVM";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};
+
+	memory at 80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee at 9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main DC jack */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixed-regulator-sd {
+		/* TPS2051BD */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	vddb: fixedregulator-vddb {
+		compatible = "regulator-fixed";
+		regulator-name = "vddb_3v3_display";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vsys_3v3>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "am64-evm:red:heartbeat";
+			gpios = <&exp1 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+	};
+};
+
+&main_pmx0 {
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
+			AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */
+			AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */
+			AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */
+			AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */
+			AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */
+			AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */
+			AM64X_IOPAD(0x029c, PIN_INPUT, 0) /* (C20) MMC1_SDWP */
+			AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */
+		>;
+	};
+
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */
+			AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */
+			AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
+			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
+			AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */
+		>;
+	};
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+/* main_uart1 is reserved for firmware usage */
+&main_uart1 {
+	status = "reserved";
+};
+
+&main_uart2 {
+	status = "disabled";
+};
+
+&main_uart3 {
+	status = "disabled";
+};
+
+&main_uart4 {
+	status = "disabled";
+};
+
+&main_uart5 {
+	status = "disabled";
+};
+
+&main_uart6 {
+	status = "disabled";
+};
+
+&mcu_uart0 {
+	status = "disabled";
+};
+
+&mcu_uart1 {
+	status = "disabled";
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio at 22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "GPIO_eMMC_RSTn", "CAN_MUX_SEL",
+				  "GPIO_CPSW1_RST", "GPIO_RGMII1_RST",
+				  "GPIO_RGMII2_RST", "GPIO_PCIe_RST_OUT",
+				  "MMC1_SD_EN", "FSI_FET_SEL",
+				  "MCAN0_STB_3V3", "MCAN1_STB_3V3",
+				  "CPSW_FET_SEL", "CPSW_FET2_SEL",
+				  "PRG1_RGMII2_FET_SEL", "TEST_GPIO2",
+				  "GPIO_OLED_RESETn", "VPP_LDO_EN",
+				  "TEST_LED1", "TP92", "TP90", "TP88",
+				  "TP87", "TP86", "TP89", "TP91";
+	};
+
+	/* osd9616p0899-10 */
+	display at 3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		reg = <0x3c>;
+		reset-gpios = <&exp1 14 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&vddb>;
+		solomon,height = <16>;
+		solomon,width = <96>;
+		solomon,com-seq;
+		solomon,com-invdir;
+		solomon,page-offset = <0>;
+		solomon,prechargep1 = <2>;
+		solomon,prechargep2 = <13>;
+	};
+};
+
+&mcu_i2c0 {
+	status = "disabled";
+};
+
+&mcu_i2c1 {
+	status = "disabled";
+};
+
+&mcu_spi0 {
+	status = "disabled";
+};
+
+&mcu_spi1 {
+	status = "disabled";
+};
+
+&sdhci0 {
+	/* emmc */
+	bus-width = <8>;
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	vmmc-supply = <&vdd_mmc1>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
-- 
2.28.0



More information about the U-Boot mailing list