[Patch v2 2/2] board: Add Zynq Mxic picozed development board support
Michal Simek
michal.simek at xilinx.com
Thu Apr 29 12:05:28 CEST 2021
On 4/29/21 11:31 AM, Zhengxun Li wrote:
> Add the Zynq Mxic picozed development board support.
>
> Signed-off-by: Zhengxun Li <zhengxunli at mxic.com.tw>
> ---
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/zynq-mxic-picozed.dts | 72 ++++++++++++++++++++++++++++++++++++++
> 2 files changed, 74 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/zynq-mxic-picozed.dts
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 1dd6c4b..b5addc4 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -287,7 +287,8 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-zturn.dtb \
> zynq-zturn-v5.dtb \
> zynq-zybo.dtb \
> - zynq-zybo-z7.dtb
> + zynq-zybo-z7.dtb \
> + zynq-mxic-picozed.dtb
> dtb-$(CONFIG_ARCH_ZYNQMP) += \
> avnet-ultra96-rev1.dtb \
> avnet-ultrazedev-cc-v1.0-ultrazedev-som-v1.0.dtb \
> diff --git a/arch/arm/dts/zynq-mxic-picozed.dts b/arch/arm/dts/zynq-mxic-picozed.dts
> new file mode 100644
> index 0000000..1f24ca1
> --- /dev/null
> +++ b/arch/arm/dts/zynq-mxic-picozed.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2021 Macronix Inc.
> + *
> + * Author: Zhengxun Li <zhengxunli at mxic.com.tw>
> + */
> +
> +/dts-v1/;
> +/include/ "zynq-7000.dtsi"
> +
> +/ {
> + model = "Zynq MXIC PicoZed Development Board";
> + compatible = "mxicy,zynq-mxic-picozed", "xlnx,zynq-7000";
> +
> + aliases {
> + ethernet0 = &gem0;
> + serial0 = &uart1;
> + spi0 = &spi_controller;
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x30000000>;
> + };
> +
> + chosen {
> + bootargs = "";
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&amba {
> + clkwizard: clkwizard at 43c20000 {
> + compatible = "xlnx,clk-wizard-5.1";
> + reg = <0x43c20000 0x10000>;
> + clocks = <&clkc 18>, <&clkc 18>;
> + clock-names = "aclk", "clk_in1";
> + #clock-cells = <1>;
> + clock-frequency = <133300000>;
> + };
> +
> + spi_controller: spi at 43c30000 {
> + compatible = "mxicy,mx25f0a-spi";
> + reg = <0x43c30000 0x10000>;
> + reg-names = "regs";
> + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 18>;
> + clock-names = "send_clk", "send_dly_clk", "ps_clk";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <1>;
> + };
> + };
> +};
> +
> +&clkc {
> + ps-clk-frequency = <33333333>;
> +};
> +
> +&gem0 {
> + status = "okay";
> + phy-mode = "rgmii-id";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
>
As I said this is clear NACK. Description for PL is not acceptable.
Thanks,
Michal
More information about the U-Boot
mailing list