[PATCH 3/3] arm: kirkwood: GoFlex Home: Use Ethernet PHY name and address from device tree

Stefan Roese sr at denx.de
Wed Aug 11 08:36:55 CEST 2021


On 30.07.21 05:02, Tony Dinh wrote:
> In DM Ethernet, the old "egiga0" name is no longer valid,
> so replace these with Ethernet PHY names from device tree. Also, read
> Ethernet PHY address from device tree.
> 
> Signed-off-by: Tony Dinh <mibodhi at gmail.com>

Reviewed-by: Stefan Roese <sr at denx.de>

Thanks,
Stefan

> ---
> 
>   board/Seagate/goflexhome/goflexhome.c | 57 +++++++++++++++++++++------
>   1 file changed, 45 insertions(+), 12 deletions(-)
> 
> diff --git a/board/Seagate/goflexhome/goflexhome.c b/board/Seagate/goflexhome/goflexhome.c
> index af8cab7bdc..52be64fb8c 100644
> --- a/board/Seagate/goflexhome/goflexhome.c
> +++ b/board/Seagate/goflexhome/goflexhome.c
> @@ -1,5 +1,9 @@
>   // SPDX-License-Identifier: GPL-2.0+
>   /*
> + * Copyright (C) 2021
> + * Tony Dinh <mibodhi at gmail.com>
> + * Suriyan Ramasami <suriyan.r at gmail.com>
> + *
>    * Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
>    *
>    * Based on dockstar.c originally written by
> @@ -107,36 +111,65 @@ int board_init(void)
>   	return 0;
>   }
>   
> +static int fdt_get_phy_addr(const char *path)
> +{
> +	const void *fdt = gd->fdt_blob;
> +	const u32 *reg;
> +	const u32 *val;
> +	int node, phandle, addr;
> +
> +	/* Find the node by its full path */
> +	node = fdt_path_offset(fdt, path);
> +	if (node >= 0) {
> +		/* Look up phy-handle */
> +		val = fdt_getprop(fdt, node, "phy-handle", NULL);
> +		if (val) {
> +			phandle = fdt32_to_cpu(*val);
> +			if (!phandle)
> +				return -1;
> +			/* Follow it to its node */
> +			node = fdt_node_offset_by_phandle(fdt, phandle);
> +			if (node) {
> +				/* Look up reg */
> +				reg = fdt_getprop(fdt, node, "reg", NULL);
> +				if (reg) {
> +					addr = fdt32_to_cpu(*reg);
> +					return addr;
> +				}
> +			}
> +		}
> +	}
> +	return -1;
> +}
> +
>   #ifdef CONFIG_RESET_PHY_R
>   /* Configure and enable MV88E1116 PHY */
>   void reset_phy(void)
>   {
>   	u16 reg;
> -	u16 devadr;
> -	char *name = "egiga0";
> +	int phyaddr;
> +	char *name = "ethernet-controller at 72000";
> +	char *eth0_path = "/ocp at f1000000/ethernet-controller at 72000/ethernet0-port at 0";
>   
>   	if (miiphy_set_current_dev(name))
>   		return;
>   
> -	/* command to read PHY dev address */
> -	if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
> -		printf("Err..%s could not read PHY dev address\n",
> -		       __func__);
> +	phyaddr = fdt_get_phy_addr(eth0_path);
> +	if (phyaddr < 0)
>   		return;
> -	}
>   
>   	/*
>   	 * Enable RGMII delay on Tx and Rx for CPU port
>   	 * Ref: sec 4.7.2 of chip datasheet
>   	 */
> -	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
> -	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
> +	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
> +	miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, &reg);
>   	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
> -	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
> -	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
> +	miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
> +	miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
>   
>   	/* reset the phy */
> -	miiphy_reset(name, devadr);
> +	miiphy_reset(name, phyaddr);
>   
>   	printf("88E1116 Initialized on %s\n", name);
>   }
> 


Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de


More information about the U-Boot mailing list