[PATCH v2] arm: mvebu: a37xx: Define CONFIG_SYS_REF_CLK and use it instead of get_ref_clk()
Stefan Roese
sr at denx.de
Tue Aug 17 09:47:19 CEST 2021
On 16.08.21 12:02, Pali Rohár wrote:
> Like for all other mvebu platforms with CONFIG_SYS_TCLK macro, define
> CONFIG_SYS_REF_CLK macro for a37xx with base reference clock value which is
> read from latched reset register.
>
> Replace all usages of get_ref_clk() function by this CONFIG_SYS_REF_CLK
> macro and completely remove get_ref_clk() function.
>
> Replace also custom open-coded implementation of determining reference
> clock by CONFIG_SYS_REF_CLK in a37xx serial driver.
>
> The only difference is that macro CONFIG_SYS_REF_CLK returns base reference
> clock in Hz and old function get_ref_clk() returned it in MHz.
>
> Signed-off-by: Pali Rohár <pali at kernel.org>
>
> ---
> Changes in v2:
> * Do not remove MVEBU_TEST_PIN_LATCH_N and MVEBU_XTAL_MODE_MASK macros
Reviewed-by: Stefan Roese <sr at denx.de>
Thanks,
Stefan
> ---
> arch/arm/mach-mvebu/armada3700/cpu.c | 24 ------------------------
> arch/arm/mach-mvebu/include/mach/cpu.h | 7 -------
> arch/arm/mach-mvebu/include/mach/soc.h | 6 ++++++
> drivers/clk/mvebu/armada-37xx-periph.c | 6 +++---
> drivers/clk/mvebu/armada-37xx-tbg.c | 4 ++--
> drivers/phy/marvell/comphy_a3700.c | 12 ++++++------
> drivers/serial/serial_mvebu_a3700.c | 11 ++++-------
> drivers/watchdog/armada-37xx-wdt.c | 2 +-
> 8 files changed, 22 insertions(+), 50 deletions(-)
>
> diff --git a/arch/arm/mach-mvebu/armada3700/cpu.c b/arch/arm/mach-mvebu/armada3700/cpu.c
> index 7702028ba19b..bdf8dc377528 100644
> --- a/arch/arm/mach-mvebu/armada3700/cpu.c
> +++ b/arch/arm/mach-mvebu/armada3700/cpu.c
> @@ -23,12 +23,6 @@
> /* Armada 3700 */
> #define MVEBU_GPIO_NB_REG_BASE (MVEBU_REGISTER(0x13800))
>
> -#define MVEBU_TEST_PIN_LATCH_N (MVEBU_GPIO_NB_REG_BASE + 0x8)
> -#define MVEBU_XTAL_MODE_MASK BIT(9)
> -#define MVEBU_XTAL_MODE_OFFS 9
> -#define MVEBU_XTAL_CLOCK_25MHZ 0x0
> -#define MVEBU_XTAL_CLOCK_40MHZ 0x1
> -
> #define MVEBU_NB_WARM_RST_REG (MVEBU_GPIO_NB_REG_BASE + 0x40)
> #define MVEBU_NB_WARM_RST_MAGIC_NUM 0x1d1e
>
> @@ -370,21 +364,3 @@ void reset_cpu(void)
> */
> writel(MVEBU_NB_WARM_RST_MAGIC_NUM, MVEBU_NB_WARM_RST_REG);
> }
> -
> -/*
> - * get_ref_clk
> - *
> - * return: reference clock in MHz (25 or 40)
> - */
> -u32 get_ref_clk(void)
> -{
> - u32 regval;
> -
> - regval = (readl(MVEBU_TEST_PIN_LATCH_N) & MVEBU_XTAL_MODE_MASK) >>
> - MVEBU_XTAL_MODE_OFFS;
> -
> - if (regval == MVEBU_XTAL_CLOCK_25MHZ)
> - return 25;
> - else
> - return 40;
> -}
> diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h b/arch/arm/mach-mvebu/include/mach/cpu.h
> index 79858858c259..9b8907e0fe55 100644
> --- a/arch/arm/mach-mvebu/include/mach/cpu.h
> +++ b/arch/arm/mach-mvebu/include/mach/cpu.h
> @@ -183,12 +183,5 @@ int a3700_dram_init_banksize(void);
> /* A3700 PCIe regions fixer for device tree */
> int a3700_fdt_fix_pcie_regions(void *blob);
>
> -/*
> - * get_ref_clk
> - *
> - * return: reference clock in MHz (25 or 40)
> - */
> -u32 get_ref_clk(void);
> -
> #endif /* __ASSEMBLY__ */
> #endif /* _MVEBU_CPU_H */
> diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h
> index aab61f7c15cf..b03b6de3c6cd 100644
> --- a/arch/arm/mach-mvebu/include/mach/soc.h
> +++ b/arch/arm/mach-mvebu/include/mach/soc.h
> @@ -210,6 +210,12 @@
> #define BOOT_FROM_SPI 0x3
>
> #define CONFIG_SYS_TCLK 250000000 /* 250MHz */
> +#elif defined(CONFIG_ARMADA_3700)
> +/* SAR values for Armada 3700 */
> +#define MVEBU_TEST_PIN_LATCH_N MVEBU_REGISTER(0x13808)
> +#define MVEBU_XTAL_MODE_MASK BIT(9)
> +#define CONFIG_SYS_REF_CLK ((readl(MVEBU_TEST_PIN_LATCH_N) & MVEBU_XTAL_MODE_MASK) ? \
> + 40000000 : 25000000)
> #endif
>
> #endif /* _MVEBU_SOC_H */
> diff --git a/drivers/clk/mvebu/armada-37xx-periph.c b/drivers/clk/mvebu/armada-37xx-periph.c
> index 3b767d706009..f5b3f5a78414 100644
> --- a/drivers/clk/mvebu/armada-37xx-periph.c
> +++ b/drivers/clk/mvebu/armada-37xx-periph.c
> @@ -14,7 +14,7 @@
> #include <clk.h>
> #include <dm.h>
> #include <asm/io.h>
> -#include <asm/arch/cpu.h>
> +#include <mach/soc.h>
> #include <dm/device_compat.h>
> #include <linux/bitops.h>
>
> @@ -501,7 +501,7 @@ int armada_37xx_tbg_clk_dump(struct udevice *);
>
> int soc_clk_dump(void)
> {
> - printf(" xtal at %u000000 Hz\n\n", get_ref_clk());
> + printf(" xtal at %u Hz\n\n", CONFIG_SYS_REF_CLK);
>
> if (clk_dump("tbg at 13200", armada_37xx_tbg_clk_dump))
> return 1;
> @@ -581,7 +581,7 @@ static int armada_37xx_periph_clk_probe(struct udevice *dev)
> struct clk clk;
>
> if (i == XTAL) {
> - priv->parents[i] = get_ref_clk() * 1000000;
> + priv->parents[i] = CONFIG_SYS_REF_CLK;
> continue;
> }
>
> diff --git a/drivers/clk/mvebu/armada-37xx-tbg.c b/drivers/clk/mvebu/armada-37xx-tbg.c
> index 054aff5e6aca..2ec60b15a6af 100644
> --- a/drivers/clk/mvebu/armada-37xx-tbg.c
> +++ b/drivers/clk/mvebu/armada-37xx-tbg.c
> @@ -13,7 +13,7 @@
> #include <clk.h>
> #include <dm.h>
> #include <asm/io.h>
> -#include <asm/arch/cpu.h>
> +#include <mach/soc.h>
> #include <dm/device_compat.h>
>
> #define NUM_TBG 4
> @@ -122,7 +122,7 @@ static int armada_37xx_tbg_clk_probe(struct udevice *dev)
> return -ENODEV;
> }
>
> - xtal = (ulong)get_ref_clk() * 1000000;
> + xtal = CONFIG_SYS_REF_CLK;
>
> for (i = 0; i < NUM_TBG; ++i) {
> unsigned int mult, div;
> diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c
> index 06822d1d12e0..5eb137db4884 100644
> --- a/drivers/phy/marvell/comphy_a3700.c
> +++ b/drivers/phy/marvell/comphy_a3700.c
> @@ -211,7 +211,7 @@ static int comphy_pcie_power_up(u32 speed, u32 invert)
> * 8. Check crystal jumper setting and program the Power and PLL
> * Control accordingly
> */
> - if (get_ref_clk() == 40) {
> + if (CONFIG_SYS_REF_CLK == 40000000) {
> /* 40 MHz */
> reg_set16(phy_addr(PCIE, PWR_PLL_CTRL), 0xFC63, 0xFFFF);
> } else {
> @@ -300,7 +300,7 @@ static int comphy_sata_power_up(u32 invert)
> /*
> * 2. Select reference clock and PHY mode (SATA)
> */
> - if (get_ref_clk() == 40) {
> + if (CONFIG_SYS_REF_CLK == 40000000) {
> /* 40 MHz */
> reg_set_indirect(vphy_power_reg0, 0x3, 0x00FF);
> } else {
> @@ -431,7 +431,7 @@ static int comphy_usb3_power_up(u32 lane, u32 type, u32 speed, u32 invert)
> * Control accordingly
> * 4. Change RX wait
> */
> - if (get_ref_clk() == 40) {
> + if (CONFIG_SYS_REF_CLK == 40000000) {
> /* 40 MHz */
> usb3_reg_set16(PWR_PLL_CTRL, 0xFCA3, 0xFFFF, lane);
> usb3_reg_set16(PWR_MGM_TIM1, 0x10C, 0xFFFF, lane);
> @@ -556,7 +556,7 @@ static int comphy_usb2_power_up(u8 usb32)
> * 0. Setup PLL. 40MHz clock uses defaults.
> * See "PLL Settings for Typical REFCLK" table
> */
> - if (get_ref_clk() == 25) {
> + if (CONFIG_SYS_REF_CLK == 25000000) {
> reg_set(USB2_PHY_BASE(usb32), 5 | (96 << 16),
> 0x3F | (0xFF << 16) | (0x3 << 28));
> }
> @@ -773,7 +773,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert)
> * 11. Set correct reference clock frequency in COMPHY register
> * REF_FREF_SEL.
> */
> - if (get_ref_clk() == 40) {
> + if (CONFIG_SYS_REF_CLK == 40000000) {
> reg_set16(sgmiiphy_addr(lane, PWR_PLL_CTRL),
> 0x4 << rf_ref_freq_sel_shift, rf_ref_freq_sel_mask);
> } else {
> @@ -820,7 +820,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert)
> */
> debug("Running C-DPI phy init %s mode\n",
> speed == COMPHY_SPEED_3_125G ? "2G5" : "1G");
> - if (get_ref_clk() == 40)
> + if (CONFIG_SYS_REF_CLK == 40000000)
> comphy_sgmii_phy_init(lane, speed);
>
> /*
> diff --git a/drivers/serial/serial_mvebu_a3700.c b/drivers/serial/serial_mvebu_a3700.c
> index efc898c08e83..b575b70050c4 100644
> --- a/drivers/serial/serial_mvebu_a3700.c
> +++ b/drivers/serial/serial_mvebu_a3700.c
> @@ -8,7 +8,7 @@
> #include <dm.h>
> #include <serial.h>
> #include <asm/io.h>
> -#include <asm/arch/cpu.h>
> +#include <mach/soc.h>
> #include <linux/delay.h>
>
> struct mvebu_plat {
> @@ -237,7 +237,7 @@ static int mvebu_serial_remove(struct udevice *dev)
>
> /* Calculate new divisor against XTAL clock without changing baudrate */
> new_oversampling = 0;
> - new_parent_rate = get_ref_clk() * 1000000;
> + new_parent_rate = CONFIG_SYS_REF_CLK;
> new_divider = DIV_ROUND_CLOSEST(new_parent_rate * divider * d1 * d2 *
> oversampling, parent_rate * 16);
>
> @@ -347,12 +347,11 @@ U_BOOT_DRIVER(serial_mvebu) = {
> #ifdef CONFIG_DEBUG_MVEBU_A3700_UART
>
> #include <debug_uart.h>
> -#include <mach/soc.h>
>
> static inline void _debug_uart_init(void)
> {
> void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
> - u32 parent_rate, divider;
> + u32 divider;
>
> /* reset FIFOs */
> writel(UART_CTRL_RXFIFO_RESET | UART_CTRL_TXFIFO_RESET,
> @@ -365,9 +364,7 @@ static inline void _debug_uart_init(void)
> * Calculate divider
> * baudrate = clock / 16 / divider
> */
> - parent_rate = (readl(MVEBU_REGISTER(0x13808)) & BIT(9)) ?
> - 40000000 : 25000000;
> - divider = DIV_ROUND_CLOSEST(parent_rate, CONFIG_BAUDRATE * 16);
> + divider = DIV_ROUND_CLOSEST(CONFIG_SYS_REF_CLK, CONFIG_BAUDRATE * 16);
> writel(divider, base + UART_BAUD_REG);
>
> /*
> diff --git a/drivers/watchdog/armada-37xx-wdt.c b/drivers/watchdog/armada-37xx-wdt.c
> index 6b5e1ab6fc35..915f37b3d8e6 100644
> --- a/drivers/watchdog/armada-37xx-wdt.c
> +++ b/drivers/watchdog/armada-37xx-wdt.c
> @@ -165,7 +165,7 @@ static int a37xx_wdt_probe(struct udevice *dev)
> goto err;
> priv->reg = (void __iomem *)addr;
>
> - priv->clk_rate = (ulong)get_ref_clk() * 1000000;
> + priv->clk_rate = CONFIG_SYS_REF_CLK;
>
> /*
> * We use counter 1 as watchdog timer, therefore we only set bit
>
Viele Grüße,
Stefan
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list