[PATCH v2 1/2] GPIO: fxl6408: Add support for FXL6408 GPIO expander

Oleksandr Suvorov oleksandr.suvorov at foundries.io
Sat Aug 28 12:23:24 CEST 2021


From: Oleksandr Suvorov <oleksandr.suvorov at toradex.com>

Initial support for Fairchild's 8 bit I2C gpio expander FXL6408.
The CONFIG_FXL6408_GPIO define enables support for such devices.

Based on: https://patchwork.kernel.org/patch/9148419/

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov at toradex.com>
Reviewed-by: Simon Glass <sjg at chromium.org>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov at foundries.io>
---

Changes in v2: None

 drivers/gpio/Kconfig        |   7 +
 drivers/gpio/Makefile       |   1 +
 drivers/gpio/gpio-fxl6408.c | 366 ++++++++++++++++++++++++++++++++++++
 3 files changed, 374 insertions(+)
 create mode 100644 drivers/gpio/gpio-fxl6408.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 4a89c1a62b..f56e4cc261 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -123,6 +123,13 @@ config DA8XX_GPIO
 	help
 	  This driver supports the DA8xx GPIO controller
 
+config FXL6408_GPIO
+	bool "FXL6408 I2C GPIO expander driver"
+	depends on DM_GPIO && DM_I2C
+	help
+	  This driver supports the Fairchild FXL6408 device. FXL6408 is a
+	  fully configurable 8-bit I2C-controlled GPIO expander.
+
 config INTEL_BROADWELL_GPIO
 	bool "Intel Broadwell GPIO driver"
 	depends on DM
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 58f4704f6b..83d8b5c9d8 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_AT91_GPIO)	+= at91_gpio.o
 obj-$(CONFIG_ATMEL_PIO4)	+= atmel_pio4.o
 obj-$(CONFIG_BCM6345_GPIO)	+= bcm6345_gpio.o
 obj-$(CONFIG_CORTINA_GPIO)      += cortina_gpio.o
+obj-$(CONFIG_FXL6408_GPIO)	+= gpio-fxl6408.o
 obj-$(CONFIG_INTEL_GPIO)	+= intel_gpio.o
 obj-$(CONFIG_INTEL_ICH6_GPIO)	+= intel_ich6_gpio.o
 obj-$(CONFIG_INTEL_BROADWELL_GPIO)	+= intel_broadwell_gpio.o
diff --git a/drivers/gpio/gpio-fxl6408.c b/drivers/gpio/gpio-fxl6408.c
new file mode 100644
index 0000000000..8a86f32365
--- /dev/null
+++ b/drivers/gpio/gpio-fxl6408.c
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Copyright (C) 2021 Toradex
+ *  Copyright (C) 2016 Broadcom
+ */
+
+/**
+ * DOC: FXL6408 I2C to GPIO expander.
+ *
+ * This chip has 8 GPIO lines out of it, and is controlled by an I2C
+ * bus (a pair of lines), providing 4x expansion of GPIO lines. It
+ * also provides an interrupt line out for notifying of state changes.
+ *
+ * Any preconfigured state will be left in place until the GPIO lines
+ * get activated. At power on, everything is treated as an input,
+ * default input is HIGH and pulled-up, all interrupts are masked.
+ *
+ * Documentation can be found at:
+ * https://www.fairchildsemi.com/datasheets/FX/FXL6408.pdf
+ *
+ * This driver bases on:
+ * - the original driver by Eric Anholt <eric at anholt.net>:
+ *   https://patchwork.kernel.org/patch/9148419/
+ * - the Toradex version by Max Krummenacher <max.krummenacher at toradex.com>:
+ *   http://git.toradex.com/cgit/linux-toradex.git/tree/drivers/gpio/gpio-fxl6408.c?h=toradex_5.4-2.3.x-imx
+ * - the U-boot PCA953x driver by Peng Fan <van.freenix at gmail.com>:
+ *   drivers/gpio/pca953x_gpio.c
+ *
+ * TODO:
+ *   - Add interrupts support
+ *   - Replace deprecated callbacks direction_input/output() with set_flags()
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <i2c.h>
+#include <log.h>
+#include <asm-generic/gpio.h>
+#include <asm/global_data.h>
+#include <linux/bitops.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#define REG_DEVID_CTRL		0x01
+# define SW_RST			BIT(0)
+# define RST_INT		BIT(1)
+/* 0b101 is the Manufacturer's ID assigned to Fairchild by Nokia */
+# define MF_ID_FAIRCHILD	5
+
+/* Bits set here indicate that the GPIO is an output */
+#define REG_IO_DIR		0x03
+
+/*
+ * Bits set here, when the corresponding bit of REG_IO_DIR is set, drive
+ * the output high instead of low.
+ */
+#define REG_OUT_STATE		0x05
+
+/* Bits here make the output High-Z, instead of the OUTPUT value */
+#define REG_OUT_HIGH_Z		0x07
+
+/*
+ * Bits here define the expected input state of the GPIO.
+ * INTERRUPT_STATUS bits will be set when the INPUT transitions away
+ * from this value.
+ */
+#define REG_IN_DEFAULT_STATE	0x09
+
+/*
+ * Bits here enable either pull up or pull down according to
+ * REG_PULL_MODE.
+ */
+#define REG_PULL_ENABLE		0x0b
+
+/*
+ * Bits set here selects a pull-up/pull-down state of pin, which
+ * is configured as Input and the corresponding REG_PULL_ENABLE bit is
+ * set.
+ */
+#define REG_PULL_MODE		0x0d
+
+/* Returns the current status (1 = HIGH) of the input pins */
+#define REG_IN_STATUS		0x0f
+
+/* Mask of pins which can generate interrupts */
+#define REG_INT_MASK		0x11
+
+/* Mask of pins which have generated an interrupt. Cleared on read */
+#define REG_INT_STATUS		0x13
+
+/* Manufacturer's ID getting from Device ID & Ctrl register */
+enum {
+	MF_ID_MASK = GENMASK(7, 5),
+	MF_ID_SHIFT = 5,
+};
+
+/* Firmware revision getting from Device ID & Ctrl register */
+enum {
+	FW_REV_MASK = GENMASK(4, 2),
+	FW_REV_SHIFT = 2,
+};
+
+enum io_direction {
+	DIR_IN,
+	DIR_OUT,
+};
+
+/*
+ * struct fxl6408_info - Data for fxl6408
+ *
+ * @dev: udevice structure for the device
+ * @addr: i2c slave address
+ * @reg_io_dir: hold the value of direction register
+ * @reg_output: hold the value of output register
+ */
+struct fxl6408_info {
+	struct udevice *dev;
+	int addr;
+	u8 device_id;
+	u8 reg_io_dir;
+	u8 reg_output;
+};
+
+static inline int fxl6408_write(struct udevice *dev, int reg, u8 val)
+{
+	return dm_i2c_write(dev, reg, &val, 1);
+}
+
+static int fxl6408_read(struct udevice *dev, int reg)
+{
+	int ret;
+	u8 tmp;
+
+	ret = dm_i2c_read(dev, reg, &tmp, 1);
+	if (!ret)
+		ret = tmp;
+
+	return ret;
+}
+
+/*
+ * fxl6408_is_output() - check whether the gpio configures as either
+ *			 output or input.
+ * Return: false - input, true - output.
+ */
+static bool fxl6408_is_output(struct udevice *dev, int offset)
+{
+	struct fxl6408_info *info = dev_get_plat(dev);
+
+	return info->reg_io_dir & BIT(offset);
+}
+
+static int fxl6408_get_value(struct udevice *dev, uint offset)
+{
+	int ret, reg = fxl6408_is_output(dev, offset) ? REG_OUT_STATE : REG_IN_STATUS;
+
+	ret = fxl6408_read(dev, reg);
+	if (ret < 0)
+		return ret;
+
+	return !!(ret & BIT(offset));
+}
+
+static int fxl6408_set_value(struct udevice *dev, uint offset, int value)
+{
+	struct fxl6408_info *info = dev_get_plat(dev);
+	u8 val;
+	int ret;
+
+	if (value)
+		val = info->reg_output | BIT(offset);
+	else
+		val = info->reg_output & ~BIT(offset);
+
+	ret = fxl6408_write(dev, REG_OUT_STATE, val);
+	if (ret < 0)
+		return ret;
+
+	info->reg_output = val;
+
+	return 0;
+}
+
+static int fxl6408_set_direction(struct udevice *dev, uint offset,
+				 enum io_direction dir)
+{
+	struct fxl6408_info *info = dev_get_plat(dev);
+	u8 val;
+	int ret;
+
+	if (dir == DIR_IN)
+		val = info->reg_io_dir & ~BIT(offset);
+	else
+		val = info->reg_io_dir | BIT(offset);
+
+	ret = fxl6408_write(dev, REG_IO_DIR, val);
+	if (ret < 0)
+		return ret;
+
+	info->reg_io_dir = val;
+
+	return 0;
+}
+
+static int fxl6408_direction_input(struct udevice *dev, uint offset)
+{
+	return fxl6408_set_direction(dev, offset, DIR_IN);
+}
+
+static int fxl6408_direction_output(struct udevice *dev, uint offset, int value)
+{
+	int ret;
+
+	/* Configure output value */
+	ret = fxl6408_set_value(dev, offset, value);
+	if (ret < 0)
+		return ret;
+	/* Configure direction as output */
+	fxl6408_set_direction(dev, offset, DIR_OUT);
+
+	return 0;
+}
+
+static int fxl6408_get_function(struct udevice *dev, uint offset)
+{
+	if (fxl6408_is_output(dev, offset))
+		return GPIOF_OUTPUT;
+	else
+		return GPIOF_INPUT;
+}
+
+static int fxl6408_xlate(struct udevice *dev, struct gpio_desc *desc,
+			 struct ofnode_phandle_args *args)
+{
+	desc->offset = args->args[0];
+	desc->flags = args->args[1] & GPIO_ACTIVE_LOW ? GPIOD_ACTIVE_LOW : 0;
+
+	return 0;
+}
+
+static const struct dm_gpio_ops fxl6408_ops = {
+	.direction_input        = fxl6408_direction_input,
+	.direction_output       = fxl6408_direction_output,
+	.get_value              = fxl6408_get_value,
+	.set_value              = fxl6408_set_value,
+	.get_function           = fxl6408_get_function,
+	.xlate                  = fxl6408_xlate,
+};
+
+static int fxl6408_probe(struct udevice *dev)
+{
+	struct fxl6408_info *info = dev_get_plat(dev);
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+	char name[32], label[32], *str;
+	int addr;
+	int ret;
+	int size;
+	const u8 *tmp;
+	u32 val32;
+
+	addr = dev_read_addr(dev);
+	if (addr == 0)
+		return -EINVAL;
+	info->addr = addr;
+
+	/*
+	 * Check the device ID register to see if it's responding.
+	 * This also clears RST_INT as a side effect, so we won't get
+	 * the "we've been power cycled" interrupt once interrupts
+	 * being enabled.
+	 */
+	ret = fxl6408_read(dev, REG_DEVID_CTRL);
+	if (ret < 0) {
+		dev_err(dev, "FXL6408 probe returned %d\n", ret);
+		return ret;
+	}
+
+	if ((ret & MF_ID_MASK) >> MF_ID_SHIFT != MF_ID_FAIRCHILD) {
+		dev_err(dev, "FXL6408 probe: wrong Manufacturer's ID: 0x%02x\n", ret);
+		return -ENXIO;
+	}
+	info->device_id = ret;
+
+	/*
+	 * Disable High-Z of outputs, so that the OUTPUT updates
+	 * actually take effect.
+	 */
+	ret = fxl6408_write(dev, REG_OUT_HIGH_Z, (u8)0);
+	if (ret < 0) {
+		dev_err(dev, "Error writing High-Z register\n");
+		return ret;
+	}
+
+	/*
+	 * If configured, set initial output state and direction,
+	 * otherwise read them from the chip.
+	 */
+	if (dev_read_u32(dev, "initial_io_dir", &val32)) {
+		ret = fxl6408_read(dev, REG_IO_DIR);
+		if (ret < 0) {
+			dev_err(dev, "Error reading direction register\n");
+			return ret;
+		}
+		info->reg_io_dir = ret;
+	} else {
+		info->reg_io_dir = val32 & 0xFF;
+		ret = fxl6408_write(dev, REG_IO_DIR, info->reg_io_dir);
+		if (ret < 0) {
+			dev_err(dev, "Error setting direction register\n");
+			return ret;
+		}
+	}
+
+	if (dev_read_u32(dev, "initial_output", &val32)) {
+		ret = fxl6408_read(dev, REG_OUT_STATE);
+		if (ret < 0) {
+			dev_err(dev, "Error reading output register\n");
+			return ret;
+		}
+		info->reg_output = ret;
+	} else {
+		info->reg_output = val32 & 0xFF;
+		ret = fxl6408_write(dev, REG_OUT_STATE, info->reg_output);
+		if (ret < 0) {
+			dev_err(dev, "Error setting output register\n");
+			return ret;
+		}
+	}
+
+	tmp = dev_read_prop(dev, "label", &size);
+	if (tmp) {
+		size = min(size, (int)sizeof(label) - 1);
+		memcpy(label, tmp, size);
+		label[size] = '\0';
+		snprintf(name, sizeof(name), "%s@%x_", label, info->addr);
+	} else {
+		snprintf(name, sizeof(name), "gpio@%x_", info->addr);
+	}
+
+	str = strdup(name);
+	if (!str)
+		return -ENOMEM;
+
+	uc_priv->bank_name = str;
+	uc_priv->gpio_count = dev_get_driver_data(dev);
+	uc_priv->gpio_base = -1;
+
+	dev_dbg(dev, "%s (FW rev. %ld) is ready\n", str,
+		(info->device_id & MF_ID_MASK) >> MF_ID_SHIFT);
+
+	return 0;
+}
+
+static const struct udevice_id fxl6408_ids[] = {
+	{ .compatible = "fcs,fxl6408", .data = 8 },
+	{ }
+};
+
+U_BOOT_DRIVER(fxl6408_gpio) = {
+	.name = "fxl6408_gpio",
+	.id = UCLASS_GPIO,
+	.ops = &fxl6408_ops,
+	.probe = fxl6408_probe,
+	.of_match = fxl6408_ids,
+	.plat_auto = sizeof(struct fxl6408_info),
+};
-- 
2.31.1



More information about the U-Boot mailing list