[PATCH v2] riscv: cancel the limitation that NR_CPUS is less than or equal to 32

[Xiang W]

在 2021-12-29星期三的 17:23 +0800，Leo Liang写道：
> Hi Xiang,
> On Wed, Dec 22, 2021 at 07:32:53AM +0800, Xiang W wrote:
> > Various specifications of riscv allow the number of hart to be
> > greater than 32. The limit of 32 is determined by
> > gd->arch.available_harts. We can eliminate this limitation through
> > bitmaps. Currently, the number of hart is limited to 4095, and 4095
> > is the limit of the RISC-V Advanced Core Local Interruptor
> > Specification.
> > 
> > Test on sifive unmatched.
> > 
> > Signed-off-by: Xiang W <wxjstz at 126.com>
> > ---
> > Changes since v1:
> > 
> > * When NR_CPUS is very large, the value of GD_AVAILABLE_HARTS will
> >   overflow the immediate range of ld/lw. This patch fixes this
> >   problem
> > 
> >  arch/riscv/Kconfig                   |  4 ++--
> >  arch/riscv/cpu/start.S               | 21 ++++++++++++++++-----
> >  arch/riscv/include/asm/global_data.h |  4 +++-
> >  arch/riscv/lib/smp.c                 |  2 +-
> >  4 files changed, 22 insertions(+), 9 deletions(-)
> > 
> > diff --git a/arch/riscv/cpu/start.S b/arch/riscv/cpu/start.S
> > index 76850ec9be..92f3b78f29 100644
> > --- a/arch/riscv/cpu/start.S
> > +++ b/arch/riscv/cpu/start.S
> > @@ -166,11 +166,22 @@ wait_for_gd_init:
> >         mv      gp, s0
> >  
> >         /* register available harts in the available_harts mask */
> > -       li      t1, 1
> > -       sll     t1, t1, tp
> > -       LREG    t2, GD_AVAILABLE_HARTS(gp)
> > -       or      t2, t2, t1
> > -       SREG    t2, GD_AVAILABLE_HARTS(gp)
> > +       li      t1, GD_AVAILABLE_HARTS
> > +       add     t1, t1, gp
> > +       LREG    t1, 0(t1)
> > +#if defined(CONFIG_ARCH_RV64I)
> > +       srli    t2, tp, 6
> > +       slli    t2, t2, 3
> > +#elif defined(CONFIG_ARCH_RV32I)
> > +       srli    t2, tp, 5
> > +       slli    t2, t2, 2
> > +#endif
> > +       add     t1, t1, t2
> > +       LREG    t2, 0(t1)
> > +       li      t3, 1
> > +       sll     t3, t3, tp
> This seems incorrect.
> Shouldn't we have "$tp % sizeof(ulong)" instead of "$tp /
> sizeof(ulong)" ?

Do you meening: "$tp % sizeof(ulong)" instead of "$tp" ?

There is such a description in the riscv specification：

SLL, SRL, and SRA perform logical left, logical right, and arithmetic
right shifts on the value in register rs1 by the shift amount held in
the lower 5 bits of register rs2.

SLL, SRL, and SRA perform logical left, logical right, and arithmetic
right shifts on the value in register rs1 by the shift amount held in
register rs2. In RV64I, only the low 6 bits of rs2 are considered for
the shift amount.

So we don’t need to perform the remainder operation.

regards，
Xiang W
> > +       or      t2, t2, t3
> > +       SREG    t2, 0(t1)
> >  
> >         amoswap.w.rl zero, zero, 0(t0)
> Best regards,
> Leo