[PATCH 08/16] arm: Remove mx53loco board
Tom Rini
trini at konsulko.com
Wed Feb 10 03:42:49 CET 2021
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Jason Liu <jason.hui.liu at nxp.com>
Signed-off-by: Tom Rini <trini at konsulko.com>
---
arch/arm/mach-imx/mx5/Kconfig | 6 -
arch/arm/mach-imx/mx5/Makefile | 1 -
board/freescale/mx53loco/Kconfig | 15 -
board/freescale/mx53loco/MAINTAINERS | 6 -
board/freescale/mx53loco/Makefile | 7 -
board/freescale/mx53loco/mx53loco.c | 367 ------------------
board/freescale/mx53loco/mx53loco_video.c | 114 ------
.../mx53loco => k+p/kp_imx53}/imximage.cfg | 0
configs/kp_imx53_defconfig | 2 +-
configs/mx53loco_defconfig | 43 --
include/configs/mx53loco.h | 181 ---------
11 files changed, 1 insertion(+), 741 deletions(-)
delete mode 100644 board/freescale/mx53loco/Kconfig
delete mode 100644 board/freescale/mx53loco/MAINTAINERS
delete mode 100644 board/freescale/mx53loco/Makefile
delete mode 100644 board/freescale/mx53loco/mx53loco.c
delete mode 100644 board/freescale/mx53loco/mx53loco_video.c
rename board/{freescale/mx53loco => k+p/kp_imx53}/imximage.cfg (100%)
delete mode 100644 configs/mx53loco_defconfig
delete mode 100644 include/configs/mx53loco.h
diff --git a/arch/arm/mach-imx/mx5/Kconfig b/arch/arm/mach-imx/mx5/Kconfig
index bde37bb97e13..b2acf766134a 100644
--- a/arch/arm/mach-imx/mx5/Kconfig
+++ b/arch/arm/mach-imx/mx5/Kconfig
@@ -61,11 +61,6 @@ config TARGET_MX53EVK
select BOARD_LATE_INIT
select MX53
-config TARGET_MX53LOCO
- bool "Support mx53loco"
- select BOARD_LATE_INIT
- select MX53
-
config TARGET_MX53PPD
bool "Support mx53ppd"
select MX53
@@ -93,7 +88,6 @@ source "board/beckhoff/mx53cx9020/Kconfig"
source "board/freescale/mx51evk/Kconfig"
source "board/freescale/mx53ard/Kconfig"
source "board/freescale/mx53evk/Kconfig"
-source "board/freescale/mx53loco/Kconfig"
source "board/freescale/mx53smd/Kconfig"
source "board/ge/mx53ppd/Kconfig"
source "board/inversepath/usbarmory/Kconfig"
diff --git a/arch/arm/mach-imx/mx5/Makefile b/arch/arm/mach-imx/mx5/Makefile
index 40d1998637ca..9692f5568eef 100644
--- a/arch/arm/mach-imx/mx5/Makefile
+++ b/arch/arm/mach-imx/mx5/Makefile
@@ -10,4 +10,3 @@ obj-y += lowlevel_init.o
# common files for mx53 dram initialization
obj-$(CONFIG_TARGET_MX53CX9020) += mx53_dram.o
-obj-$(CONFIG_TARGET_MX53LOCO) += mx53_dram.o
diff --git a/board/freescale/mx53loco/Kconfig b/board/freescale/mx53loco/Kconfig
deleted file mode 100644
index 5ca1672bf7a5..000000000000
--- a/board/freescale/mx53loco/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MX53LOCO
-
-config SYS_BOARD
- default "mx53loco"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mx5"
-
-config SYS_CONFIG_NAME
- default "mx53loco"
-
-endif
diff --git a/board/freescale/mx53loco/MAINTAINERS b/board/freescale/mx53loco/MAINTAINERS
deleted file mode 100644
index b4bd1a1842bd..000000000000
--- a/board/freescale/mx53loco/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MX53LOCO BOARD
-M: Jason Liu <jason.hui.liu at nxp.com>
-S: Maintained
-F: board/freescale/mx53loco/
-F: include/configs/mx53loco.h
-F: configs/mx53loco_defconfig
diff --git a/board/freescale/mx53loco/Makefile b/board/freescale/mx53loco/Makefile
deleted file mode 100644
index d2ebd94dca1d..000000000000
--- a/board/freescale/mx53loco/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-# Jason Liu <r64343 at freescale.com>
-
-obj-y += mx53loco.o
-obj-$(CONFIG_VIDEO) += mx53loco_video.o
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
deleted file mode 100644
index 1da263bb5d5f..000000000000
--- a/board/freescale/mx53loco/mx53loco.c
+++ /dev/null
@@ -1,367 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc.
- * Jason Liu <r64343 at freescale.com>
- */
-
-#include <common.h>
-#include <init.h>
-#include <log.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux-mx53.h>
-#include <asm/arch/clock.h>
-#include <env.h>
-#include <linux/errno.h>
-#include <asm/mach-imx/mx5_video.h>
-#include <netdev.h>
-#include <i2c.h>
-#include <input.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <asm/gpio.h>
-#include <power/pmic.h>
-#include <dialog_pmic.h>
-#include <fsl_pmic.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-
-#define MX53LOCO_LCD_POWER IMX_GPIO_NR(3, 24)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-u32 get_board_rev(void)
-{
- struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
- struct fuse_bank *bank = &iim->bank[0];
- struct fuse_bank0_regs *fuse =
- (struct fuse_bank0_regs *)bank->fuse_regs;
-
- int rev = readl(&fuse->gp[6]);
-
- if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR))
- rev = 0;
-
- return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
-}
-
-#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
-
-static void setup_iomux_uart(void)
-{
- static const iomux_v3_cfg_t uart_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX, UART_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX, UART_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-}
-
-#ifdef CONFIG_USB_EHCI_MX5
-int board_ehci_hcd_init(int port)
-{
- /* request VBUS power enable pin, GPIO7_8 */
- imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
- gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
- return 0;
-}
-#endif
-
-static void setup_iomux_fec(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
- PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
- NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
- PAD_CTL_HYS | PAD_CTL_PKE),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[2] = {
- {MMC_SDHC1_BASE_ADDR},
- {MMC_SDHC3_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret;
-
- imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11);
- gpio_direction_input(IMX_GPIO_NR(3, 11));
- imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13);
- gpio_direction_input(IMX_GPIO_NR(3, 13));
-
- if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
- ret = !gpio_get_value(IMX_GPIO_NR(3, 13));
- else
- ret = !gpio_get_value(IMX_GPIO_NR(3, 11));
-
- return ret;
-}
-
-#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP)
-#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_DSE_HIGH)
-
-int board_mmc_init(struct bd_info *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
- MX53_PAD_EIM_DA13__GPIO3_13,
- };
-
- static const iomux_v3_cfg_t sd2_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
- SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
- MX53_PAD_EIM_DA11__GPIO3_11,
- };
-
- u32 index;
- int ret;
-
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-
- for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
- switch (index) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(sd1_pads,
- ARRAY_SIZE(sd1_pads));
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(sd2_pads,
- ARRAY_SIZE(sd2_pads));
- break;
- default:
- printf("Warning: you configured more ESDHC controller"
- "(%d) as supported by the board(2)\n",
- CONFIG_SYS_FSL_ESDHC_NUM);
- return -EINVAL;
- }
- ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-#endif
-
-#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
-
-static void setup_iomux_i2c(void)
-{
- static const iomux_v3_cfg_t i2c1_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
-}
-
-static int power_init(void)
-{
- unsigned int val;
- int ret;
- struct pmic *p;
-
- if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) {
- ret = pmic_dialog_init(I2C_PMIC);
- if (ret)
- return ret;
-
- p = pmic_get("DIALOG_PMIC");
- if (!p)
- return -ENODEV;
-
- env_set("fdt_file", "imx53-qsb.dtb");
-
- /* Set VDDA to 1.25V */
- val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
- ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
- if (ret) {
- printf("Writing to BUCKCORE_REG failed: %d\n", ret);
- return ret;
- }
-
- pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
- val |= DA9052_SUPPLY_VBCOREGO;
- ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val);
- if (ret) {
- printf("Writing to SUPPLY_REG failed: %d\n", ret);
- return ret;
- }
-
- /* Set Vcc peripheral to 1.30V */
- ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
- if (ret) {
- printf("Writing to BUCKPRO_REG failed: %d\n", ret);
- return ret;
- }
-
- ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
- if (ret) {
- printf("Writing to SUPPLY_REG failed: %d\n", ret);
- return ret;
- }
-
- return ret;
- }
-
- if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) {
- ret = pmic_init(I2C_0);
- if (ret)
- return ret;
-
- p = pmic_get("FSL_PMIC");
- if (!p)
- return -ENODEV;
-
- env_set("fdt_file", "imx53-qsrb.dtb");
-
- /* Set VDDGP to 1.25V for 1GHz on SW1 */
- pmic_reg_read(p, REG_SW_0, &val);
- val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
- ret = pmic_reg_write(p, REG_SW_0, val);
- if (ret) {
- printf("Writing to REG_SW_0 failed: %d\n", ret);
- return ret;
- }
-
- /* Set VCC as 1.30V on SW2 */
- pmic_reg_read(p, REG_SW_1, &val);
- val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708;
- ret = pmic_reg_write(p, REG_SW_1, val);
- if (ret) {
- printf("Writing to REG_SW_1 failed: %d\n", ret);
- return ret;
- }
-
- /* Set global reset timer to 4s */
- pmic_reg_read(p, REG_POWER_CTL2, &val);
- val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708;
- ret = pmic_reg_write(p, REG_POWER_CTL2, val);
- if (ret) {
- printf("Writing to REG_POWER_CTL2 failed: %d\n", ret);
- return ret;
- }
-
- /* Set VUSBSEL and VUSBEN for USB PHY supply*/
- pmic_reg_read(p, REG_MODE_0, &val);
- val |= (VUSBSEL_MC34708 | VUSBEN_MC34708);
- ret = pmic_reg_write(p, REG_MODE_0, val);
- if (ret) {
- printf("Writing to REG_MODE_0 failed: %d\n", ret);
- return ret;
- }
-
- /* Set SWBST to 5V in auto mode */
- val = SWBST_AUTO;
- ret = pmic_reg_write(p, SWBST_CTRL, val);
- if (ret) {
- printf("Writing to SWBST_CTRL failed: %d\n", ret);
- return ret;
- }
-
- return ret;
- }
-
- return -1;
-}
-
-static void clock_1GHz(void)
-{
- int ret;
- u32 ref_clk = MXC_HCLK;
- /*
- * After increasing voltage to 1.25V, we can switch
- * CPU clock to 1GHz and DDR to 400MHz safely
- */
- ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
- if (ret)
- printf("CPU: Switch CPU clock to 1GHZ failed\n");
-
- ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
- ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
- if (ret)
- printf("CPU: Switch DDR clock to 400MHz failed\n");
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
- setup_iomux_fec();
- setup_iomux_lcd();
-
- return 0;
-}
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-int board_init(void)
-{
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- mxc_set_sata_internal_clock();
- setup_iomux_i2c();
-
- return 0;
-}
-
-int board_late_init(void)
-{
- if (!power_init())
- clock_1GHz();
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: MX53 LOCO\n");
-
- return 0;
-}
diff --git a/board/freescale/mx53loco/mx53loco_video.c b/board/freescale/mx53loco/mx53loco_video.c
deleted file mode 100644
index ff3fc8ce3e6f..000000000000
--- a/board/freescale/mx53loco/mx53loco_video.c
+++ /dev/null
@@ -1,114 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- * Fabio Estevam <fabio.estevam at freescale.com>
- */
-
-#include <common.h>
-#include <env.h>
-#include <linux/list.h>
-#include <asm/gpio.h>
-#include <asm/arch/iomux-mx53.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-
-#define MX53LOCO_LCD_POWER IMX_GPIO_NR(3, 24)
-
-static struct fb_videomode const claa_wvga = {
- .name = "CLAA07LC0ACW",
- .refresh = 57,
- .xres = 800,
- .yres = 480,
- .pixclock = 37037,
- .left_margin = 40,
- .right_margin = 60,
- .upper_margin = 10,
- .lower_margin = 10,
- .hsync_len = 20,
- .vsync_len = 10,
- .sync = 0,
- .vmode = FB_VMODE_NONINTERLACED
-};
-
-static struct fb_videomode const seiko_wvga = {
- .name = "Seiko-43WVF1G",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 29851, /* picosecond (33.5 MHz) */
- .left_margin = 89,
- .right_margin = 164,
- .upper_margin = 23,
- .lower_margin = 10,
- .hsync_len = 10,
- .vsync_len = 10,
- .sync = 0,
-};
-
-void setup_iomux_lcd(void)
-{
- static const iomux_v3_cfg_t lcd_pads[] = {
- MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
- MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
- MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
- MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
- MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
- MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
- MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
- MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
- MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
- MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
- MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
- MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
- MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
- MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
- MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
- MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
- MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
- MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
- MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
- MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
- MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
- MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
- MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
- MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
- MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
- MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
- MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
- MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
- };
-
- imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
-
- /* Turn on GPIO backlight */
- imx_iomux_v3_setup_pad(MX53_PAD_EIM_D24__GPIO3_24);
- gpio_direction_output(MX53LOCO_LCD_POWER, 1);
-
- /* Turn on display contrast */
- imx_iomux_v3_setup_pad(MX53_PAD_GPIO_1__GPIO1_1);
- gpio_direction_output(IMX_GPIO_NR(1, 1), 1);
-}
-
-int board_video_skip(void)
-{
- int ret;
- char const *e = env_get("panel");
-
- if (e) {
- if (strcmp(e, "seiko") == 0) {
- ret = ipuv3_fb_init(&seiko_wvga, 0, IPU_PIX_FMT_RGB24);
- if (ret)
- printf("Seiko cannot be configured: %d\n", ret);
- return ret;
- }
- }
-
- /*
- * 'panel' env variable not found or has different value than 'seiko'
- * Defaulting to claa lcd.
- */
- ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
- if (ret)
- printf("CLAA cannot be configured: %d\n", ret);
- return ret;
-}
diff --git a/board/freescale/mx53loco/imximage.cfg b/board/k+p/kp_imx53/imximage.cfg
similarity index 100%
rename from board/freescale/mx53loco/imximage.cfg
rename to board/k+p/kp_imx53/imximage.cfg
diff --git a/configs/kp_imx53_defconfig b/configs/kp_imx53_defconfig
index 717543805619..fd0405106b3c 100644
--- a/configs/kp_imx53_defconfig
+++ b/configs/kp_imx53_defconfig
@@ -10,7 +10,7 @@ CONFIG_ENV_OFFSET_REDUND=0x102000
CONFIG_DEFAULT_DEVICE_TREE="imx53-kp"
CONFIG_FIT=y
CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53loco/imximage.cfg"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/k+p/kp_imx53/imximage.cfg"
CONFIG_SHOW_BOOT_PROGRESS=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_STOP_STR="."
diff --git a/configs/mx53loco_defconfig b/configs/mx53loco_defconfig
deleted file mode 100644
index a1096a7f93f5..000000000000
--- a/configs/mx53loco_defconfig
+++ /dev/null
@@ -1,43 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX5=y
-CONFIG_SYS_TEXT_BASE=0x77800000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0xC0000
-CONFIG_TARGET_MX53LOCO=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53loco/imximage.cfg"
-CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SATA=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DWC_AHSATA=y
-CONFIG_FSL_ESDHC_IMX=y
-CONFIG_MTD=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_MX5=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_MCS7830=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_SYS_WHITE_ON_BLACK=y
-CONFIG_SPLASH_SCREEN=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
deleted file mode 100644
index a0dd33aecd3a..000000000000
--- a/include/configs/mx53loco.h
+++ /dev/null
@@ -1,181 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc.
- * Jason Liu <r64343 at freescale.com>
- *
- * Configuration settings for Freescale MX53 low cost board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MACH_TYPE MACH_TYPE_MX53_LOCO
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_SYS_FSL_CLK
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-
-#define CONFIG_REVISION_TAG
-
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_ESDHC_NUM 2
-
-/* Eth Configs */
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR 0x1F
-
-/* USB Configs */
-#define CONFIG_MXC_USB_PORT 1
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_DIALOG_POWER
-#define CONFIG_POWER_FSL
-#define CONFIG_POWER_FSL_MC13892
-#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
-#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
-
-/* Command definition */
-
-
-#define CONFIG_ETHPRIME "FEC0"
-
-#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=zImage\0" \
- "fdt_addr=0x71000000\0" \
- "boot_fdt=try\0" \
- "ip_dyn=yes\0" \
- "mmcdev=0\0" \
- "mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
- "mmcargs=setenv bootargs console=ttymxc0,${baudrate} root=${mmcroot}\0" \
- "loadbootscript=" \
- "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "netargs=setenv bootargs console=ttymxc0,${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo ERROR: Cannot load the DT; " \
- "exit; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
-
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-/* Physical Memory Map */
-#define PHYS_SDRAM_1 CSD0_BASE_ADDR
-#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
-#define PHYS_SDRAM_2 CSD1_BASE_ADDR
-#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
-#define PHYS_SDRAM_SIZE (gd->ram_size)
-
-#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
-#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
-#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* Environment starts at 768k = 768 * 1024 = 786432 */
-/*
- * Detect overlap between U-Boot image and environment area in build-time
- *
- * CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot.imx offset
- * CONFIG_BOARD_SIZE_LIMIT = 768k - 1k = 767k = 785408
- *
- * Currently CONFIG_BOARD_SIZE_LIMIT does not handle expressions, so
- * write the direct value here
- */
-#define CONFIG_BOARD_SIZE_LIMIT 785408
-
-#ifdef CONFIG_CMD_SATA
- #define CONFIG_SYS_SATA_MAX_DEVICE 1
- #define CONFIG_DWC_AHSATA_PORT_ID 0
- #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_BASE_ADDR
- #define CONFIG_LBA48
-#endif
-
-/* Framebuffer and LCD */
-#define CONFIG_VIDEO_LOGO
-
-#endif /* __CONFIG_H */
--
2.17.1
More information about the U-Boot
mailing list