[PATCH 2/4] mx53loco: Convert to driver model
Fabio Estevam
festevam at gmail.com
Sun Feb 14 02:49:52 CET 2021
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam at gmail.com>
---
I will add the DM SATA support later.
arch/arm/dts/Makefile | 1 +
board/freescale/mx53loco/mx53loco.c | 124 ----------------------------
configs/mx53loco_defconfig | 22 ++++-
include/configs/mx53loco.h | 6 --
4 files changed, 20 insertions(+), 133 deletions(-)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index af2842a0f8bf..4fd3eabd6e8f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -654,6 +654,7 @@ dtb-$(CONFIG_MX28) += \
imx28-xea.dtb
dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \
+ imx53-qsb.dtb \
imx53-kp.dtb \
imx53-m53menlo.dtb
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index 1da263bb5d5f..e9391e0aef54 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -17,10 +17,8 @@
#include <env.h>
#include <linux/errno.h>
#include <asm/mach-imx/mx5_video.h>
-#include <netdev.h>
#include <i2c.h>
#include <input.h>
-#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <asm/gpio.h>
#include <power/pmic.h>
@@ -61,127 +59,6 @@ static void setup_iomux_uart(void)
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
-#ifdef CONFIG_USB_EHCI_MX5
-int board_ehci_hcd_init(int port)
-{
- /* request VBUS power enable pin, GPIO7_8 */
- imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
- gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
- return 0;
-}
-#endif
-
-static void setup_iomux_fec(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
- PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
- NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
- NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
- PAD_CTL_HYS | PAD_CTL_PKE),
- NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
- PAD_CTL_HYS | PAD_CTL_PKE),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[2] = {
- {MMC_SDHC1_BASE_ADDR},
- {MMC_SDHC3_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret;
-
- imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11);
- gpio_direction_input(IMX_GPIO_NR(3, 11));
- imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13);
- gpio_direction_input(IMX_GPIO_NR(3, 13));
-
- if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
- ret = !gpio_get_value(IMX_GPIO_NR(3, 13));
- else
- ret = !gpio_get_value(IMX_GPIO_NR(3, 11));
-
- return ret;
-}
-
-#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP)
-#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_DSE_HIGH)
-
-int board_mmc_init(struct bd_info *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
- MX53_PAD_EIM_DA13__GPIO3_13,
- };
-
- static const iomux_v3_cfg_t sd2_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
- SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
- MX53_PAD_EIM_DA11__GPIO3_11,
- };
-
- u32 index;
- int ret;
-
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-
- for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
- switch (index) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(sd1_pads,
- ARRAY_SIZE(sd1_pads));
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(sd2_pads,
- ARRAY_SIZE(sd2_pads));
- break;
- default:
- printf("Warning: you configured more ESDHC controller"
- "(%d) as supported by the board(2)\n",
- CONFIG_SYS_FSL_ESDHC_NUM);
- return -EINVAL;
- }
- ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-#endif
-
#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
@@ -326,7 +203,6 @@ static void clock_1GHz(void)
int board_early_init_f(void)
{
setup_iomux_uart();
- setup_iomux_fec();
setup_iomux_lcd();
return 0;
diff --git a/configs/mx53loco_defconfig b/configs/mx53loco_defconfig
index a1096a7f93f5..2828889b03ee 100644
--- a/configs/mx53loco_defconfig
+++ b/configs/mx53loco_defconfig
@@ -1,11 +1,14 @@
CONFIG_ARM=y
CONFIG_ARCH_MX5=y
CONFIG_SYS_TEXT_BASE=0x77800000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_NR_DRAM_BANKS=2
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0xC0000
CONFIG_TARGET_MX53LOCO=y
+CONFIG_DM_GPIO=y
# CONFIG_CMD_BMODE is not set
+CONFIG_DEFAULT_DEVICE_TREE="imx53-qsb"
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53loco/imximage.cfg"
CONFIG_USE_PREBOOT=y
@@ -13,8 +16,9 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_DM=y
CONFIG_CMD_MMC=y
-CONFIG_CMD_SATA=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -23,15 +27,28 @@ CONFIG_CMD_PING=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DWC_AHSATA=y
+CONFIG_DM=y
+CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC_IMX=y
CONFIG_MTD=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX5=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_MXC_UART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_EHCI_MX5=y
CONFIG_USB_STORAGE=y
CONFIG_USB_HOST_ETHER=y
@@ -40,4 +57,3 @@ CONFIG_USB_ETHER_MCS7830=y
CONFIG_USB_ETHER_SMSC95XX=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_SPLASH_SCREEN=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index a0dd33aecd3a..e5dc9ac1d9e2 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -30,12 +30,6 @@
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_FSL_ESDHC_NUM 2
-/* Eth Configs */
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR 0x1F
-
/* USB Configs */
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
--
2.25.1
More information about the U-Boot
mailing list