[PATCH 21/57] arm: Remove platinum_picon board
Tom Rini
trini at konsulko.com
Sun Feb 21 02:05:58 CET 2021
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <sr at denx.de>
Signed-off-by: Tom Rini <trini at konsulko.com>
---
arch/arm/mach-imx/mx6/Kconfig | 9 -
board/barco/platinum/Kconfig | 31 ---
board/barco/platinum/MAINTAINERS | 7 -
board/barco/platinum/Makefile | 12 --
board/barco/platinum/platinum.c | 219 --------------------
board/barco/platinum/platinum.h | 77 -------
board/barco/platinum/platinum_picon.c | 244 -----------------------
board/barco/platinum/platinum_titanium.c | 209 -------------------
board/barco/platinum/spl_picon.c | 183 -----------------
board/barco/platinum/spl_titanium.c | 186 -----------------
configs/platinum_picon_defconfig | 67 -------
configs/platinum_titanium_defconfig | 69 -------
include/configs/platinum.h | 189 ------------------
include/configs/platinum_picon.h | 25 ---
include/configs/platinum_titanium.h | 30 ---
15 files changed, 1557 deletions(-)
delete mode 100644 board/barco/platinum/Kconfig
delete mode 100644 board/barco/platinum/MAINTAINERS
delete mode 100644 board/barco/platinum/Makefile
delete mode 100644 board/barco/platinum/platinum.c
delete mode 100644 board/barco/platinum/platinum.h
delete mode 100644 board/barco/platinum/platinum_picon.c
delete mode 100644 board/barco/platinum/platinum_titanium.c
delete mode 100644 board/barco/platinum/spl_picon.c
delete mode 100644 board/barco/platinum/spl_titanium.c
delete mode 100644 configs/platinum_picon_defconfig
delete mode 100644 configs/platinum_titanium_defconfig
delete mode 100644 include/configs/platinum.h
delete mode 100644 include/configs/platinum_picon.h
delete mode 100644 include/configs/platinum_titanium.h
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 221727411005..ca54da567389 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -499,14 +499,6 @@ config TARGET_LITEBOARD
select BOARD_LATE_INIT
select MX6UL_LITESOM
-config TARGET_PLATINUM_PICON
- bool "platinum-picon"
- select SUPPORT_SPL
-
-config TARGET_PLATINUM_TITANIUM
- bool "platinum-titanium"
- select SUPPORT_SPL
-
config TARGET_PCM058
bool "Phytec PCM058 i.MX6 Quad"
depends on MX6Q
@@ -690,7 +682,6 @@ source "board/ge/b1x5v2/Kconfig"
source "board/advantech/dms-ba16/Kconfig"
source "board/aristainetos/Kconfig"
source "board/armadeus/opos6uldev/Kconfig"
-source "board/barco/platinum/Kconfig"
source "board/barco/titanium/Kconfig"
source "board/boundary/nitrogen6x/Kconfig"
source "board/bticino/mamoj/Kconfig"
diff --git a/board/barco/platinum/Kconfig b/board/barco/platinum/Kconfig
deleted file mode 100644
index cc0648cd73b3..000000000000
--- a/board/barco/platinum/Kconfig
+++ /dev/null
@@ -1,31 +0,0 @@
-if TARGET_PLATINUM_PICON
-
-config SYS_CPU
- default "armv7"
-
-config SYS_VENDOR
- default "barco"
-
-config SYS_BOARD
- default "platinum"
-
-config SYS_CONFIG_NAME
- default "platinum_picon"
-
-endif
-
-if TARGET_PLATINUM_TITANIUM
-
-config SYS_CPU
- default "armv7"
-
-config SYS_VENDOR
- default "barco"
-
-config SYS_BOARD
- default "platinum"
-
-config SYS_CONFIG_NAME
- default "platinum_titanium"
-
-endif
diff --git a/board/barco/platinum/MAINTAINERS b/board/barco/platinum/MAINTAINERS
deleted file mode 100644
index a22584b5e586..000000000000
--- a/board/barco/platinum/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-PLATINUM BOARD
-M: Stefan Roese <sr at denx.de>
-S: Maintained
-F: board/barco/platinum/
-F: include/configs/platinum.h
-F: configs/platinum_picon_defconfig
-F: configs/platinum_titanium_defconfig
diff --git a/board/barco/platinum/Makefile b/board/barco/platinum/Makefile
deleted file mode 100644
index 1e1bf101a8b0..000000000000
--- a/board/barco/platinum/Makefile
+++ /dev/null
@@ -1,12 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2014, Barco (www.barco.com)
-
-obj-y := platinum.o
-obj-$(CONFIG_TARGET_PLATINUM_PICON) += platinum_picon.o
-obj-$(CONFIG_TARGET_PLATINUM_TITANIUM) += platinum_titanium.o
-
-ifneq ($(CONFIG_SPL_BUILD),)
-obj-$(CONFIG_TARGET_PLATINUM_PICON) += spl_picon.o
-obj-$(CONFIG_TARGET_PLATINUM_TITANIUM) += spl_titanium.o
-endif
diff --git a/board/barco/platinum/platinum.c b/board/barco/platinum/platinum.c
deleted file mode 100644
index ec8d55288876..000000000000
--- a/board/barco/platinum/platinum.c
+++ /dev/null
@@ -1,219 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- */
-
-#include <common.h>
-#include <init.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-
-#include "platinum.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t nfc_pads[] = {
- MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS1__NAND_CE1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS2__NAND_CE2_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS3__NAND_CE3_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-struct fsl_esdhc_cfg usdhc_cfg[] = {
- { USDHC3_BASE_ADDR },
-};
-
-void setup_gpmi_nand(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- /* config gpmi nand iomux */
- imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
-
- /* config gpmi and bch clock to 100 MHz */
- clrsetbits_le32(&mxc_ccm->cs2cdr,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
-
- /* enable gpmi and bch clock gating */
- setbits_le32(&mxc_ccm->CCGR4,
- MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
- MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
-
- /* enable apbh clock gating */
- setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
- return 0;
-}
-
-int board_ehci_hcd_init(int port)
-{
- return 0;
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
- if (cfg->esdhc_base == usdhc_cfg[0].esdhc_base) {
- unsigned sd3_cd = IMX_GPIO_NR(7, 0);
- gpio_direction_input(sd3_cd);
- return !gpio_get_value(sd3_cd);
- }
-
- return 0;
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-}
-
-void board_init_gpio(void)
-{
- platinum_init_gpio();
-}
-
-void board_init_gpmi_nand(void)
-{
- setup_gpmi_nand();
-}
-
-void board_init_i2c(void)
-{
- platinum_setup_i2c();
-}
-
-void board_init_spi(void)
-{
- platinum_setup_spi();
-}
-
-void board_init_uart(void)
-{
- platinum_setup_uart();
-}
-
-void board_init_usb(void)
-{
- platinum_init_usb();
-}
-
-void board_init_finished(void)
-{
- platinum_init_finished();
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- return platinum_phy_config(phydev);
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- return cpu_eth_init(bis);
-}
-
-int board_early_init_f(void)
-{
- board_init_uart();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- board_init_spi();
-
- board_init_i2c();
-
- board_init_gpmi_nand();
-
- board_init_gpio();
-
- board_init_usb();
-
- board_init_finished();
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: " CONFIG_PLATINUM_BOARD "\n");
- return 0;
-}
-
-static const struct boot_mode board_boot_modes[] = {
- /* NAND */
- { "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) },
- /* 4 bit bus width */
- { "mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00) },
- { "mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00) },
- { NULL, 0 },
-};
-
-int misc_init_r(void)
-{
- add_board_boot_modes(board_boot_modes);
-
- return 0;
-}
diff --git a/board/barco/platinum/platinum.h b/board/barco/platinum/platinum.h
deleted file mode 100644
index 9988caec1250..000000000000
--- a/board/barco/platinum/platinum.h
+++ /dev/null
@@ -1,77 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- */
-
-#ifndef _PLATINUM_H_
-#define _PLATINUM_H_
-
-#include <miiphy.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/io.h>
-
-/* Defines */
-
-#define ECSPI1_PAD_CLK (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS)
-#define ECSPI2_PAD_CLK (PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS)
-#define ECSPI_PAD_MOSI (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
- PAD_CTL_HYS)
-#define ECSPI_PAD_MISO (PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
- PAD_CTL_HYS)
-#define ECSPI_PAD_SS (PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
- PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL_SCL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_SLOW)
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
- PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
- PAD_CTL_HYS)
-
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-#define PC_SCL MUX_PAD_CTRL(I2C_PAD_CTRL_SCL)
-
-/* Prototypes */
-
-int platinum_setup_enet(void);
-int platinum_setup_i2c(void);
-int platinum_setup_spi(void);
-int platinum_setup_uart(void);
-int platinum_phy_config(struct phy_device *phydev);
-int platinum_init_gpio(void);
-int platinum_init_usb(void);
-int platinum_init_finished(void);
-
-static inline void ccgr_init(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- writel(0x00C03F3F, &ccm->CCGR0);
- writel(0x0030FC03, &ccm->CCGR1);
- writel(0x0FFFC000, &ccm->CCGR2);
- writel(0x3FF00000, &ccm->CCGR3);
- writel(0xFFFFF300, &ccm->CCGR4); /* enable NAND/GPMI/BCH clks */
- writel(0x0F0000C3, &ccm->CCGR5);
- writel(0x000003FF, &ccm->CCGR6);
-}
-
-#endif /* _PLATINUM_H_ */
diff --git a/board/barco/platinum/platinum_picon.c b/board/barco/platinum/platinum_picon.c
deleted file mode 100644
index 3fc29f9e08c4..000000000000
--- a/board/barco/platinum/platinum_picon.c
+++ /dev/null
@@ -1,244 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- */
-
-#include <common.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <linux/delay.h>
-
-#include "platinum.h"
-
-#define GPIO_IP_NCONFIG IMX_GPIO_NR(5, 18)
-#define GPIO_HK_NCONFIG IMX_GPIO_NR(7, 13)
-#define GPIO_LS_NCONFIG IMX_GPIO_NR(5, 19)
-
-#define GPIO_I2C0_SEL0 IMX_GPIO_NR(5, 2)
-#define GPIO_I2C0_SEL1 IMX_GPIO_NR(1, 11)
-#define GPIO_I2C0_ENBN IMX_GPIO_NR(1, 13)
-
-#define GPIO_I2C2_SEL0 IMX_GPIO_NR(1, 17)
-#define GPIO_I2C2_SEL1 IMX_GPIO_NR(1, 20)
-#define GPIO_I2C2_ENBN IMX_GPIO_NR(1, 14)
-
-#define GPIO_USB_RESET IMX_GPIO_NR(1, 5)
-
-iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI1_PAD_CLK),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
- MX6_PAD_CSI0_DAT7__ECSPI1_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
- MX6_PAD_EIM_D24__ECSPI1_SS2 | MUX_PAD_CTRL(ECSPI_PAD_SS),
- MX6_PAD_EIM_D25__ECSPI1_SS3 | MUX_PAD_CTRL(ECSPI_PAD_SS),
-};
-
-iomux_v3_cfg_t const ecspi2_pads[] = {
- MX6_PAD_EIM_CS0__ECSPI2_SCLK | MUX_PAD_CTRL(ECSPI2_PAD_CLK),
- MX6_PAD_EIM_OE__ECSPI2_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
- MX6_PAD_EIM_CS1__ECSPI2_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
- MX6_PAD_EIM_RW__ECSPI2_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
- MX6_PAD_EIM_LBA__ECSPI2_SS1 | MUX_PAD_CTRL(ECSPI_PAD_SS),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-/* PHY nRESET */
-iomux_v3_cfg_t const phy_reset_pad = {
- MX6_PAD_SD1_DAT2__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart4_pads[] = {
- MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart5_pads[] = {
- MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const i2c0_mux_pads[] = {
- MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD2_CMD__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD2_DAT2__GPIO1_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const i2c2_mux_pads[] = {
- MX6_PAD_SD1_DAT1__GPIO1_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD2_DAT1__GPIO1_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-struct i2c_pads_info i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC_SCL,
- .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC_SCL,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC_SCL,
- .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC_SCL,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-
-/*
- * This enet related pin-muxing and GPIO handling is done
- * in SPL U-Boot. For early initialization. And to give the
- * PHY some time to come out of reset before the U-Boot
- * ethernet driver tries to access its registers via MDIO.
- */
-int platinum_setup_enet(void)
-{
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- unsigned phy_reset = IMX_GPIO_NR(1, 19);
-
- /* First configure PHY reset GPIO pin */
- imx_iomux_v3_setup_pad(phy_reset_pad);
-
- /* Reconfigure enet muxing while PHY is in reset */
- gpio_direction_output(phy_reset, 0);
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
- mdelay(10);
- gpio_set_value(phy_reset, 1);
- udelay(100);
-
- /* set GPIO_16 as ENET_REF_CLK_OUT */
- setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
-
- return enable_fec_anatop_clock(0, ENET_50MHZ);
-}
-
-int platinum_setup_i2c(void)
-{
- imx_iomux_v3_setup_multiple_pads(i2c0_mux_pads,
- ARRAY_SIZE(i2c0_mux_pads));
- imx_iomux_v3_setup_multiple_pads(i2c2_mux_pads,
- ARRAY_SIZE(i2c2_mux_pads));
-
- mdelay(10);
-
- /* Disable i2c mux 0 */
- gpio_direction_output(GPIO_I2C0_SEL0, 0);
- gpio_direction_output(GPIO_I2C0_SEL1, 0);
- gpio_direction_output(GPIO_I2C0_ENBN, 1);
-
- /* Disable i2c mux 1 */
- gpio_direction_output(GPIO_I2C2_SEL0, 0);
- gpio_direction_output(GPIO_I2C2_SEL1, 0);
- gpio_direction_output(GPIO_I2C2_ENBN, 1);
-
- udelay(10);
-
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
- /* Disable all leds */
- i2c_set_bus_num(0);
- i2c_reg_write(0x60, 0x05, 0x55);
-
- return 0;
-}
-
-int platinum_setup_spi(void)
-{
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
- imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
-
- return 0;
-}
-
-int platinum_setup_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
- imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
-
- return 0;
-}
-
-int platinum_phy_config(struct phy_device *phydev)
-{
- /* Use generic infrastructure, no specific setup */
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int platinum_init_gpio(void)
-{
- /* Reset FPGA's */
- gpio_direction_output(GPIO_IP_NCONFIG, 0);
- gpio_direction_output(GPIO_HK_NCONFIG, 0);
- gpio_direction_output(GPIO_LS_NCONFIG, 0);
- udelay(3);
- gpio_set_value(GPIO_IP_NCONFIG, 1);
- gpio_set_value(GPIO_HK_NCONFIG, 1);
- gpio_set_value(GPIO_LS_NCONFIG, 1);
-
- /* no dmd configuration yet */
-
- return 0;
-}
-
-int platinum_init_usb(void)
-{
- /* Reset usb hub */
- gpio_direction_output(GPIO_USB_RESET, 0);
- udelay(100);
- gpio_set_value(GPIO_USB_RESET, 1);
-
- return 0;
-}
-
-int platinum_init_finished(void)
-{
- /* Enable led 0 */
- i2c_set_bus_num(0);
- i2c_reg_write(0x60, 0x05, 0x54);
-
- return 0;
-}
diff --git a/board/barco/platinum/platinum_titanium.c b/board/barco/platinum/platinum_titanium.c
deleted file mode 100644
index 9f7c93b4d540..000000000000
--- a/board/barco/platinum/platinum_titanium.c
+++ /dev/null
@@ -1,209 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- */
-
-#include <common.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <miiphy.h>
-#include <micrel.h>
-#include <linux/delay.h>
-
-#include "platinum.h"
-
-iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI1_PAD_CLK),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
- MX6_PAD_CSI0_DAT7__ECSPI1_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
- /* non mounted spi nor flash for booting */
- MX6_PAD_EIM_D19__ECSPI1_SS1 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EIM_D24__ECSPI1_SS2 | MUX_PAD_CTRL(ECSPI_PAD_SS),
- MX6_PAD_EIM_D25__ECSPI1_SS3 | MUX_PAD_CTRL(ECSPI_PAD_SS),
-};
-
-iomux_v3_cfg_t const ecspi2_pads[] = {
- MX6_PAD_EIM_CS0__ECSPI2_SCLK | MUX_PAD_CTRL(ECSPI2_PAD_CLK),
- MX6_PAD_EIM_OE__ECSPI2_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
- MX6_PAD_EIM_CS1__ECSPI2_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
- MX6_PAD_EIM_RW__ECSPI2_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
-};
-
-iomux_v3_cfg_t const enet_pads1[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- /* pin 35 - 1 (PHY_AD2) on reset */
- MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 32 - 1 - (MODE0) all */
- MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 31 - 1 - (MODE1) all */
- MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 28 - 1 - (MODE2) all */
- MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 27 - 1 - (MODE3) all */
- MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
- MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* pin 42 PHY nRST */
- MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads2[] = {
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D28__UART2_DTE_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D29__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart4_pads[] = {
- MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-struct i2c_pads_info i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC_SCL,
- .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC_SCL,
- .gp = IMX_GPIO_NR(5, 27)
- },
- .sda = {
- .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
- .gp = IMX_GPIO_NR(5, 26)
- }
-};
-
-struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC_SCL,
- .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC_SCL,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | PC,
- .gp = IMX_GPIO_NR(7, 11)
- }
-};
-
-/*
- * This enet related pin-muxing and GPIO handling is done
- * in SPL U-Boot. For early initialization. And to give the
- * PHY some time to come out of reset before the U-Boot
- * ethernet driver tries to access its registers via MDIO.
- */
-int platinum_setup_enet(void)
-{
- gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
- gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
- gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
- gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
- gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
- gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
- imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
- gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
-
- /* Need delay 10ms according to KSZ9021 spec */
- mdelay(10);
- gpio_set_value(IMX_GPIO_NR(3, 23), 1);
- udelay(100);
-
- imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
-
- return 0;
-}
-
-int platinum_setup_i2c(void)
-{
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
- return 0;
-}
-
-int platinum_setup_spi(void)
-{
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
- imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
-
- return 0;
-}
-
-int platinum_setup_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
- imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
-
- return 0;
-}
-
-int platinum_phy_config(struct phy_device *phydev)
-{
- /* min rx data delay */
- ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
- 0x0);
- /* min tx data delay */
- ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
- 0x0);
- /* max rx/tx clock delay, min rx/tx control */
- ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
- 0xf0f0);
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int platinum_init_gpio(void)
-{
- /* Default GPIO's */
- /* Toggle CONFIG_n to reset fpga on every boot */
- gpio_direction_output(IMX_GPIO_NR(5, 18), 0);
- /* Need delay >=2uS */
- udelay(3);
- gpio_set_value(IMX_GPIO_NR(5, 18), 1);
-
- /* Default pin 1,15 high - DLP_FLASH_WPZ */
- gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
-
- return 0;
-}
-
-int platinum_init_usb(void)
-{
- return 0;
-}
-
-int platinum_init_finished(void)
-{
- return 0;
-}
diff --git a/board/barco/platinum/spl_picon.c b/board/barco/platinum/spl_picon.c
deleted file mode 100644
index 253a64d28eba..000000000000
--- a/board/barco/platinum/spl_picon.c
+++ /dev/null
@@ -1,183 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- *
- * Based on: gw_ventana_spl.c which is:
- * Copyright (C) 2014 Gateworks Corporation
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <init.h>
-#include <asm/io.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <spl.h>
-
-#include "platinum.h"
-
-#undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
-
-/* Configure MX6Q/DUAL mmdc DDR io registers */
-struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
- /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
- .dram_sdclk_0 = 0x00020030,
- .dram_sdclk_1 = 0x00020030,
- .dram_cas = 0x00020030,
- .dram_ras = 0x00020030,
- .dram_reset = 0x00020030,
- /* SDCKE[0:1]: 100k pull-up */
- .dram_sdcke0 = 0x00003000,
- .dram_sdcke1 = 0x00003000,
- /* SDBA2: pull-up disabled */
- .dram_sdba2 = 0x00000000,
- /* SDODT[0:1]: 100k pull-up, 40 ohm */
- .dram_sdodt0 = 0x00003030,
- .dram_sdodt1 = 0x00003030,
- /* SDQS[0:7]: Differential input, 40 ohm */
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
- /* DQM[0:7]: Differential input, 40 ohm */
- .dram_dqm0 = 0x00020030,
- .dram_dqm1 = 0x00020030,
- .dram_dqm2 = 0x00020030,
- .dram_dqm3 = 0x00020030,
- .dram_dqm4 = 0x00020030,
- .dram_dqm5 = 0x00020030,
- .dram_dqm6 = 0x00020030,
- .dram_dqm7 = 0x00020030,
-};
-
-/* Configure MX6Q/DUAL mmdc GRP io registers */
-struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
- /* DDR3 */
- .grp_ddr_type = 0x000c0000,
- .grp_ddrmode_ctl = 0x00020000,
- /* disable DDR pullups */
- .grp_ddrpke = 0x00000000,
- /* ADDR[00:16], SDBA[0:1]: 40 ohm */
- .grp_addds = 0x00000030,
- /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
- .grp_ctlds = 0x00000030,
- /* DATA[00:63]: Differential input, 40 ohm */
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_b2ds = 0x00000030,
- .grp_b3ds = 0x00000030,
- .grp_b4ds = 0x00000030,
- .grp_b5ds = 0x00000030,
- .grp_b6ds = 0x00000030,
- .grp_b7ds = 0x00000030,
-};
-
-/* MT41K256M16HA-125 */
-static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
- .mem_speed = 1600,
- .density = 4, /* 4Gbit */
- .width = 16,
- .banks = 8,
- .rowaddr = 15,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-/*
- * Values from running the Freescale DDR stress tool via USB
- */
-static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x0044004E,
- .p0_mpwldectrl1 = 0x001F0023,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x02480248,
- .p0_mpdgctrl1 = 0x0210021C,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x42444444,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x36322C32,
-};
-
-static void spl_dram_init(int width)
-{
- struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125;
- struct mx6_ddr_sysinfo sysinfo = {
- /* width of data bus:0=16,1=32,2=64 */
- .dsize = width / 32,
- /* config for full 4GB range so that get_mem_size() works */
- .cs_density = 32, /* 32Gb per CS */
- /* single chip select */
- .ncs = 1,
- .cs1_mirror = 1,
- .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
-#ifdef RTT_NOM_120OHM
- .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
-#else
- .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
-#endif
- .walat = 0, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
- };
-
- mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
- mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
-}
-
-/*
- * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
- * - we have a stack and a place to store GD, both in SRAM
- * - no variable global data is available
- */
-void board_init_f(ulong dummy)
-{
- /* Setup AIPS and disable watchdog */
- arch_cpu_init();
-
- ccgr_init();
- gpr_init();
-
- /* UART iomux */
- board_early_init_f();
-
- /* Setup GP timer */
- timer_init();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* Init DDR with 32bit width */
- spl_dram_init(32);
-
- /* Clear the BSS */
- memset(__bss_start, 0, __bss_end - __bss_start);
-
- /*
- * Setup enet related MUXing early to give the PHY
- * some time to wake-up from reset
- */
- platinum_setup_enet();
-
- /* load/boot image from boot device */
- board_init_r(NULL, 0);
-}
diff --git a/board/barco/platinum/spl_titanium.c b/board/barco/platinum/spl_titanium.c
deleted file mode 100644
index 8c91b752ffe0..000000000000
--- a/board/barco/platinum/spl_titanium.c
+++ /dev/null
@@ -1,186 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Stefan Roese <sr at denx.de>
- *
- * Based on: gw_ventana_spl.c which is:
- * Copyright (C) 2014 Gateworks Corporation
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <init.h>
-#include <asm/io.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <spl.h>
-
-#include "platinum.h"
-
-#undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
-
-/* Configure MX6Q/DUAL mmdc DDR io registers */
-struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
- /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
- .dram_sdclk_0 = 0x00020030,
- .dram_sdclk_1 = 0x00020030,
- .dram_cas = 0x00020030,
- .dram_ras = 0x00020030,
- .dram_reset = 0x00020030,
- /* SDCKE[0:1]: 100k pull-up */
- .dram_sdcke0 = 0x00003000,
- .dram_sdcke1 = 0x00003000,
- /* SDBA2: pull-up disabled */
- .dram_sdba2 = 0x00000000,
- /* SDODT[0:1]: 100k pull-up, 40 ohm */
- .dram_sdodt0 = 0x00003030,
- .dram_sdodt1 = 0x00003030,
- /* SDQS[0:7]: Differential input, 40 ohm */
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
- /* DQM[0:7]: Differential input, 40 ohm */
- .dram_dqm0 = 0x00020030,
- .dram_dqm1 = 0x00020030,
- .dram_dqm2 = 0x00020030,
- .dram_dqm3 = 0x00020030,
- .dram_dqm4 = 0x00020030,
- .dram_dqm5 = 0x00020030,
- .dram_dqm6 = 0x00020030,
- .dram_dqm7 = 0x00020030,
-};
-
-/* Configure MX6Q/DUAL mmdc GRP io registers */
-struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
- /* DDR3 */
- .grp_ddr_type = 0x000c0000,
- .grp_ddrmode_ctl = 0x00020000,
- /* disable DDR pullups */
- .grp_ddrpke = 0x00000000,
- /* ADDR[00:16], SDBA[0:1]: 40 ohm */
- .grp_addds = 0x00000030,
- /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
- .grp_ctlds = 0x00000030,
- /* DATA[00:63]: Differential input, 40 ohm */
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_b2ds = 0x00000030,
- .grp_b3ds = 0x00000030,
- .grp_b4ds = 0x00000030,
- .grp_b5ds = 0x00000030,
- .grp_b6ds = 0x00000030,
- .grp_b7ds = 0x00000030,
-};
-
-/* MT41J128M16JT-125 */
-static struct mx6_ddr3_cfg mt41j128m16jt_125 = {
- .mem_speed = 1600,
- .density = 2,
- .width = 16,
- .banks = 8,
- .rowaddr = 14,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
- /* Write leveling calibration determine */
- .p0_mpwldectrl0 = 0x001f001f,
- .p0_mpwldectrl1 = 0x001f001f,
- .p1_mpwldectrl0 = 0x00440044,
- .p1_mpwldectrl1 = 0x00440044,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x434b0350,
- .p0_mpdgctrl1 = 0x034c0359,
- .p1_mpdgctrl0 = 0x434b0350,
- .p1_mpdgctrl1 = 0x03650348,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x4436383b,
- .p1_mprddlctl = 0x39393341,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x35373933,
- .p1_mpwrdlctl = 0x48254a36,
-};
-
-static void spl_dram_init(int width)
-{
- struct mx6_ddr3_cfg *mem = &mt41j128m16jt_125;
- struct mx6_ddr_sysinfo sysinfo = {
- /* width of data bus:0=16,1=32,2=64 */
- .dsize = width / 32,
- /* config for full 4GB range so that get_mem_size() works */
- .cs_density = 32, /* 32Gb per CS */
- /* single chip select */
- .ncs = 1,
- .cs1_mirror = 1,
- .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
-#ifdef RTT_NOM_120OHM
- .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
-#else
- .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
-#endif
- .walat = 0, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
- };
-
- mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs);
- mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
-}
-
-/*
- * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
- * - we have a stack and a place to store GD, both in SRAM
- * - no variable global data is available
- */
-void board_init_f(ulong dummy)
-{
- /* Setup AIPS and disable watchdog */
- arch_cpu_init();
-
- ccgr_init();
- gpr_init();
-
- /* UART iomux */
- board_early_init_f();
-
- /* Setup GP timer */
- timer_init();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* Init DDR with 32bit width */
- spl_dram_init(32);
-
- /* Clear the BSS */
- memset(__bss_start, 0, __bss_end - __bss_start);
-
- /*
- * Setup enet related MUXing early to give the PHY
- * some time to wake-up from reset
- */
- platinum_setup_enet();
-
- /* load/boot image from boot device */
- board_init_r(NULL, 0);
-}
diff --git a/configs/platinum_picon_defconfig b/configs/platinum_picon_defconfig
deleted file mode 100644
index 47c38b8d342a..000000000000
--- a/configs/platinum_picon_defconfig
+++ /dev/null
@@ -1,67 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x1000000
-CONFIG_MX6DL=y
-CONFIG_TARGET_PLATINUM_PICON=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x1080000
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_DMA=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="picon > "
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:14M(spl),2M(uboot),512k(env1),512k(env2),495M(ubi0),14M(res0),2M(res1),512k(res2),512k(res3),-(ubi1)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_PHYLIB=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/platinum_titanium_defconfig b/configs/platinum_titanium_defconfig
deleted file mode 100644
index 3ceb4e102030..000000000000
--- a/configs/platinum_titanium_defconfig
+++ /dev/null
@@ -1,69 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x1000000
-CONFIG_MX6Q=y
-CONFIG_TARGET_PLATINUM_TITANIUM=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x1080000
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_PREBOOT=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_DMA=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="titanium > "
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:14M(spl),2M(uboot),512k(env1),512k(env2),-(ubi)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ90X1=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/platinum.h b/include/configs/platinum.h
deleted file mode 100644
index 325a28001e5b..000000000000
--- a/include/configs/platinum.h
+++ /dev/null
@@ -1,189 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- */
-
-#ifndef __PLATINUM_CONFIG_H__
-#define __PLATINUM_CONFIG_H__
-
-/* SPL */
-
-/* Location in NAND to read U-Boot from */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * 1024 * 1024)
-
-#include "imx6_spl.h" /* common IMX6 SPL configuration */
-#include "mx6_common.h"
-
-/*
- * Hardware configuration
- */
-
-/* UART config */
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-/* I2C config */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED 100000
-
-/* MMC config */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_USDHC_NUM 1
-
-/* Ethernet config */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-
-/* USB config */
-#define CONFIG_MXC_USB_PORT 1
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-
-/* Memory config */
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-#ifndef PHYS_SDRAM_SIZE
-#define PHYS_SDRAM_SIZE (1024 << 20)
-#endif
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_SYS_MALLOC_LEN (16 * 1024 * 1024)
-
-#ifdef CONFIG_CMD_NAND
-
-/* NAND config */
-#ifndef CONFIG_SYS_NAND_MAX_CHIPS
-#define CONFIG_SYS_NAND_MAX_CHIPS 2
-#endif
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* DMA config, needed for GPMI/MXS NAND support */
-
-/* Environment in NAND */
-
-#else /* CONFIG_CMD_NAND */
-
-/* Environment in MMC */
-
-#endif /* CONFIG_CMD_NAND */
-
-/*
- * U-Boot configuration
- */
-
-/* Board startup config */
-
-#define CONFIG_BOOTCOMMAND "run bootubi_scr"
-
-/* Miscellaneous configurable options */
-
-/* MTD/UBI/UBIFS config */
-
-/*
- * Environment configuration
- */
-
-#if (CONFIG_SYS_NAND_MAX_CHIPS == 1)
-#define CONFIG_COMMON_ENV_UBI \
- "setubipartition=env set ubipartition ubi\0" \
- "setubirfs=env set ubirfs $ubipartition:rootfs$boot_vol\0"
-#elif (CONFIG_SYS_NAND_MAX_CHIPS == 2)
-#define CONFIG_COMMON_ENV_UBI \
- "setubipartition=env set ubipartition ubi$boot_vol\0" \
- "setubirfs=env set ubirfs ubi0:rootfs\0"
-#endif
-
-#define CONFIG_COMMON_ENV_MISC \
- "user=user\0" \
- "project="CONFIG_PLATINUM_PROJECT"\0" \
- "uimage=uImage\0" \
- "dtb="CONFIG_PLATINUM_CPU"-platinum-"CONFIG_PLATINUM_PROJECT".dtb\0" \
- "serverip=serverip\0" \
- "memaddrlinux=0x10800000\0" \
- "memaddrsrc=0x11000000\0" \
- "memaddrdtb=0x12000000\0" \
- "console=ttymxc0\0" \
- "baudrate=115200\0" \
- "boot_scr=boot.uboot\0" \
- "boot_vol=0\0" \
- "mtdids="CONFIG_MTDIDS_DEFAULT"\0" \
- "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0" \
- "mmcfs=ext2\0" \
- "mmcrootpart=1\0" \
- \
- "setnfspath=env set nfspath /home/nfs/$user/$project/root\0" \
- "settftpfilelinux=env set tftpfilelinux $user/$project/$uimage\0" \
- "settftpfiledtb=env set tftpfiledtb $user/$project/$dtb\0" \
- "setubifilelinux=env set ubifilelinux boot/$uimage\0" \
- "setubipfiledtb=env set ubifiledtb boot/$dtb\0" \
- "setmmcrootdev=env set mmcrootdev /dev/mmcblk0p$mmcrootpart\0" \
- "setmmcfilelinux=env set mmcfilelinux /boot/$uimage\0" \
- "setmmcfiledtb=env set mmcfiledtb /boot/$dtb\0" \
- \
- "loadtftpkernel=dhcp $memaddrlinux $tftpfilelinux\0" \
- "loadtftpdtb=dhcp $memaddrdtb $tftpfiledtb\0" \
- "loadubikernel=ubifsload $memaddrlinux $ubifilelinux\0" \
- "loadubidtb=ubifsload $memaddrdtb $ubifiledtb\0" \
- "loadmmckernel=${mmcfs}load mmc 0:$mmcrootpart $memaddrlinux " \
- "$mmcfilelinux\0" \
- "loadmmcdtb=${mmcfs}load mmc 0:$mmcrootpart $memaddrdtb " \
- "$mmcfiledtb\0" \
- \
- "ubipart=ubi part $ubipartition\0" \
- "ubimount=ubifsmount $ubirfs\0" \
- \
- "setbootargscommon=env set bootargs $bootargs " \
- "console=$console,$baudrate enable_wait_mode=off\0" \
- "setbootargsmtd=env set bootargs $bootargs $mtdparts\0" \
- "setbootargsdhcp=env set bootargs $bootargs ip=dhcp\0" \
- "setbootargsubirfs=env set bootargs $bootargs " \
- "ubi.mtd=$ubipartition root=$ubirfs rootfstype=ubifs\0" \
- "setbootargsnfsrfs=env set bootargs $bootargs root=/dev/nfs " \
- "nfsroot=$serverip:$nfspath,v3,tcp\0" \
- "setbootargsmmcrfs=env set bootargs $bootargs " \
- "root=$mmcrootdev rootwait rw\0" \
- \
- "bootnet=run settftpfilelinux settftpfiledtb setnfspath " \
- "setbootargscommon setbootargsmtd setbootargsdhcp " \
- "setbootargsnfsrfs;" \
- "run loadtftpkernel loadtftpdtb;" \
- "bootm $memaddrlinux - $memaddrdtb\0" \
- "bootnet_ubirfs=run settftpfilelinux settftpfiledtb;" \
- "run setubipartition setubirfs;" \
- "run setbootargscommon setbootargsmtd " \
- "setbootargsubirfs;" \
- "run loadtftpkernel loadtftpdtb;" \
- "bootm $memaddrlinux - $memaddrdtb\0" \
- "bootubi=run setubipartition setubirfs setubifilelinux " \
- "setubipfiledtb;" \
- "run setbootargscommon setbootargsmtd " \
- "setbootargsubirfs;" \
- "run ubipart ubimount loadubikernel loadubidtb;" \
- "bootm $memaddrlinux - $memaddrdtb\0" \
- "bootubi_scr=run setubipartition setubirfs;" \
- "run ubipart ubimount;" \
- "if ubifsload ${memaddrsrc} boot/${boot_scr}; " \
- "then source ${memaddrsrc}; else run bootubi; fi\0" \
- "bootmmc=run setmmcrootdev setmmcfilelinux setmmcfiledtb " \
- "setbootargscommon setbootargsmmcrfs;" \
- "run loadmmckernel loadmmcdtb;" \
- "bootm $memaddrlinux - $memaddrdtb\0" \
- \
- "bootcmd="CONFIG_BOOTCOMMAND"\0"
-
-#define CONFIG_COMMON_ENV_SETTINGS CONFIG_COMMON_ENV_MISC \
- CONFIG_COMMON_ENV_UBI
-#endif /* __PLATINUM_CONFIG_H__ */
diff --git a/include/configs/platinum_picon.h b/include/configs/platinum_picon.h
deleted file mode 100644
index 1b55e7397928..000000000000
--- a/include/configs/platinum_picon.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- */
-
-#ifndef __PLATINUM_PICON_CONFIG_H__
-#define __PLATINUM_PICON_CONFIG_H__
-
-#define CONFIG_PLATINUM_BOARD "Barco Picon"
-#define CONFIG_PLATINUM_PROJECT "picon"
-#define CONFIG_PLATINUM_CPU "imx6dl"
-
-#include <configs/platinum.h>
-
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_FEC_MXC_PHYADDR 0
-
-#define CONFIG_HOSTNAME "picon"
-
-#define CONFIG_PLATFORM_ENV_SETTINGS "\0"
-
-#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_COMMON_ENV_SETTINGS \
- CONFIG_PLATFORM_ENV_SETTINGS
-
-#endif /* __PLATINUM_PICON_CONFIG_H__ */
diff --git a/include/configs/platinum_titanium.h b/include/configs/platinum_titanium.h
deleted file mode 100644
index b4028832e937..000000000000
--- a/include/configs/platinum_titanium.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014, Barco (www.barco.com)
- */
-
-#ifndef __PLATINUM_TITANIUM_CONFIG_H__
-#define __PLATINUM_TITANIUM_CONFIG_H__
-
-#define CONFIG_PLATINUM_BOARD "Barco Titanium"
-#define CONFIG_PLATINUM_PROJECT "titanium"
-#define CONFIG_PLATINUM_CPU "imx6q"
-
-#define PHYS_SDRAM_SIZE (512 << 20)
-#define CONFIG_SYS_NAND_MAX_CHIPS 1
-
-#include <configs/platinum.h>
-
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_FEC_MXC_PHYADDR 4
-
-#define CONFIG_PHY_RESET_DELAY 1000
-
-#define CONFIG_HOSTNAME "titanium"
-
-#define CONFIG_PLATFORM_ENV_SETTINGS "\0"
-
-#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_COMMON_ENV_SETTINGS \
- CONFIG_PLATFORM_ENV_SETTINGS
-
-#endif /* __PLATINUM_TITANIUM_CONFIG_H__ */
--
2.17.1
More information about the U-Boot
mailing list