[PATCH 31/57] arm: Remove zc5202 and zc5601 boards
Tom Rini
trini at konsulko.com
Sun Feb 21 02:06:08 CET 2021
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <sbabic at denx.de>
Signed-off-by: Tom Rini <trini at konsulko.com>
---
arch/arm/mach-imx/mx6/Kconfig | 17 -
board/el/el6x/Kconfig | 25 --
board/el/el6x/MAINTAINERS | 8 -
board/el/el6x/Makefile | 5 -
board/el/el6x/el6x.c | 637 ----------------------------------
configs/zc5202_defconfig | 62 ----
configs/zc5601_defconfig | 60 ----
include/configs/zc5202.h | 27 --
include/configs/zc5601.h | 26 --
9 files changed, 867 deletions(-)
delete mode 100644 board/el/el6x/Kconfig
delete mode 100644 board/el/el6x/MAINTAINERS
delete mode 100644 board/el/el6x/Makefile
delete mode 100644 board/el/el6x/el6x.c
delete mode 100644 configs/zc5202_defconfig
delete mode 100644 configs/zc5601_defconfig
delete mode 100644 include/configs/zc5202.h
delete mode 100644 include/configs/zc5601.h
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 8401374732f9..dadf5ebdbe07 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -608,22 +608,6 @@ config TARGET_WANDBOARD
select BOARD_LATE_INIT
select SUPPORT_SPL
-config TARGET_ZC5202
- bool "zc5202"
- select BOARD_LATE_INIT
- select DM
- select DM_THERMAL
- select SUPPORT_SPL
- imply CMD_DM
-
-config TARGET_ZC5601
- bool "zc5601"
- select BOARD_LATE_INIT
- select DM
- select DM_THERMAL
- select SUPPORT_SPL
- imply CMD_DM
-
config TARGET_BRPPT2
bool "brppt2"
depends on MX6QDL
@@ -657,7 +641,6 @@ source "board/bticino/mamoj/Kconfig"
source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
source "board/dhelectronics/dh_imx6/Kconfig"
-source "board/el/el6x/Kconfig"
source "board/engicam/imx6q/Kconfig"
source "board/engicam/imx6ul/Kconfig"
source "board/freescale/mx6qarm2/Kconfig"
diff --git a/board/el/el6x/Kconfig b/board/el/el6x/Kconfig
deleted file mode 100644
index aa9bf25fb472..000000000000
--- a/board/el/el6x/Kconfig
+++ /dev/null
@@ -1,25 +0,0 @@
-if TARGET_ZC5202
-
-config SYS_BOARD
- default "el6x"
-
-config SYS_VENDOR
- default "el"
-
-config SYS_CONFIG_NAME
- default "zc5202"
-
-endif
-
-if TARGET_ZC5601
-
-config SYS_BOARD
- default "el6x"
-
-config SYS_VENDOR
- default "el"
-
-config SYS_CONFIG_NAME
- default "zc5601"
-
-endif
diff --git a/board/el/el6x/MAINTAINERS b/board/el/el6x/MAINTAINERS
deleted file mode 100644
index 9a40010f50e9..000000000000
--- a/board/el/el6x/MAINTAINERS
+++ /dev/null
@@ -1,8 +0,0 @@
-EL6X BOARD
-M: Stefano Babic <sbabic at denx.de>
-S: Maintained
-F: board/el/el6x/
-F: include/configs/zc5202.h
-F: include/configs/zc5601.h
-F: configs/zc5202_defconfig
-F: configs/zc5601_defconfig
diff --git a/board/el/el6x/Makefile b/board/el/el6x/Makefile
deleted file mode 100644
index 065a867475aa..000000000000
--- a/board/el/el6x/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) Stefano Babic <sbabic at denx.de>
-
-obj-y := el6x.o
diff --git a/board/el/el6x/el6x.c b/board/el/el6x/el6x.c
deleted file mode 100644
index ddac58f73d28..000000000000
--- a/board/el/el6x/el6x.c
+++ /dev/null
@@ -1,637 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) Stefano Babic <sbabic at denx.de>
- *
- * Based on other i.MX6 boards
- */
-
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <env.h>
-#include <asm/global_data.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/video.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/io.h>
-#include <asm/arch/sys_proto.h>
-#include <i2c.h>
-#include <input.h>
-#include <power/pmic.h>
-#include <power/pfuze100_pmic.h>
-#include <asm/arch/mx6-ddr.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define OPEN_PAD_CTRL (PAD_CTL_ODE | PAD_CTL_DSE_DISABLE | (0 << 12))
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PMIC 1
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-#define ETH_PHY_RESET IMX_GPIO_NR(2, 4)
-
-int dram_init(void)
-{
- gd->ram_size = imx_ddr_size();
-
- return 0;
-}
-
-iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_SD3_DAT5__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_SD3_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
-}
-
-#ifdef CONFIG_TARGET_ZC5202
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_GPIO_18__ENET_RX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_KEY_COL2__ENET_RX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_KEY_COL0__ENET_RX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
- MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_GPIO_19__ENET_TX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_KEY_ROW2__ENET_TX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_KEY_ROW0__ENET_TX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
- /* Switch Reset */
- MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
- /* Switch Interrupt */
- MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* use CRS and COL pads as GPIOs */
- MX6_PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(OPEN_PAD_CTRL),
- MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(OPEN_PAD_CTRL),
-
-};
-
-#define BOARD_NAME "EL6x-ZC5202"
-#else
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-#define BOARD_NAME "EL6x-ZC5601"
-#endif
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
-#ifdef CONFIG_TARGET_ZC5202
- /* set CRS and COL to input */
- gpio_direction_input(IMX_GPIO_NR(4, 9));
- gpio_direction_input(IMX_GPIO_NR(4, 12));
-
- /* Reset Switch */
- gpio_direction_output(ETH_PHY_RESET , 0);
- mdelay(2);
- gpio_set_value(ETH_PHY_RESET, 1);
-#endif
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-#ifdef CONFIG_MXC_SPI
-#ifdef CONFIG_TARGET_ZC5202
-iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_DISP0_DAT20__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT21__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT22__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_DISP0_DAT15__GPIO5_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const ecspi3_pads[] = {
- MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT7__GPIO4_IO28 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT8__GPIO4_IO29 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT9__GPIO4_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT10__GPIO4_IO31 | MUX_PAD_CTRL(SPI_PAD_CTRL),
-};
-#endif
-
-iomux_v3_cfg_t const ecspi4_pads[] = {
- MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
- ? (IMX_GPIO_NR(3, 20)) : -1;
-}
-
-static void setup_spi(void)
-{
-#ifdef CONFIG_TARGET_ZC5202
- gpio_request(IMX_GPIO_NR(5, 17), "spi_cs0");
- gpio_request(IMX_GPIO_NR(5, 9), "spi_cs1");
- gpio_direction_output(IMX_GPIO_NR(5, 17), 1);
- gpio_direction_output(IMX_GPIO_NR(5, 9), 1);
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
-#endif
-
- gpio_request(IMX_GPIO_NR(3, 20), "spi4_cs0");
- gpio_direction_output(IMX_GPIO_NR(3, 20), 1);
- imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
-
- enable_spi_clk(true, 3);
-}
-#endif
-
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | I2C_PAD,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 5)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | I2C_PAD,
- .gp = IMX_GPIO_NR(7, 11)
- }
-};
-
-iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_GPIO_4__SD2_CD_B | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC2_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
-#ifndef CONFIG_SPL_BUILD
- int ret;
- int i;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-boot device node) (Physical Port)
- * mmc0 SD2
- * mmc1 SD3
- * mmc2 eMMC
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-#else
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned reg = readl(&psrc->sbmr1) >> 11;
-
- /*
- * Upon reading BOOT_CFG register the following map is done:
- * Bit 11 and 12 of BOOT_CFG register can determine the current
- * mmc port
- * 0x1 SD1
- * 0x2 SD2
- * 0x3 SD4
- */
-
- switch (reg & 0x3) {
- case 0x1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x3:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- }
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-
-}
-#endif
-
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- setup_iomux_enet();
- enable_enet_clk(1);
-
- return cpu_eth_init(bis);
-}
-
-int board_early_init_f(void)
-{
-
- setup_iomux_uart();
- setup_spi();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
- return 0;
-}
-
-int power_init_board(void)
-{
- struct pmic *p;
- int ret;
- unsigned int reg;
-
- ret = power_pfuze100_init(I2C_PMIC);
- if (ret)
- return ret;
-
- p = pmic_get("PFUZE100");
- ret = pmic_probe(p);
- if (ret)
- return ret;
-
- pmic_reg_read(p, PFUZE100_DEVICEID, ®);
- printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
-
- /* Increase VGEN3 from 2.5 to 2.8V */
- pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
- reg &= ~LDO_VOL_MASK;
- reg |= LDOB_2_80V;
- pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
-
- /* Increase VGEN5 from 2.8 to 3V */
- pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
- reg &= ~LDO_VOL_MASK;
- reg |= LDOB_3_00V;
- pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
-
- /* Set SW1AB stanby volage to 0.975V */
- pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®);
- reg &= ~SW1x_STBY_MASK;
- reg |= SW1x_0_975V;
- pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
-
- /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE100_SW1ABCONF, ®);
- reg &= ~SW1xCONF_DVSSPEED_MASK;
- reg |= SW1xCONF_DVSSPEED_4US;
- pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
-
- /* Set SW1C standby voltage to 0.975V */
- pmic_reg_read(p, PFUZE100_SW1CSTBY, ®);
- reg &= ~SW1x_STBY_MASK;
- reg |= SW1x_0_975V;
- pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
-
- /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE100_SW1CCONF, ®);
- reg &= ~SW1xCONF_DVSSPEED_MASK;
- reg |= SW1xCONF_DVSSPEED_4US;
- pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
-
- return 0;
-}
-
-#ifdef CONFIG_CMD_BMODE
-static const struct boot_mode board_boot_modes[] = {
- /* 4 bit bus width */
- {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
- /* 8 bit bus width */
- {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
- {NULL, 0},
-};
-#endif
-
-int board_late_init(void)
-{
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-
- env_set("board_name", BOARD_NAME);
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: ");
- puts(BOARD_NAME "\n");
-
- return 0;
-}
-
-#ifdef CONFIG_SPL_BUILD
-#include <spl.h>
-#include <linux/libfdt.h>
-
-const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
- .dram_sdclk_0 = 0x00020030,
- .dram_sdclk_1 = 0x00020030,
- .dram_cas = 0x00020030,
- .dram_ras = 0x00020030,
- .dram_reset = 0x00020030,
- .dram_sdcke0 = 0x00003000,
- .dram_sdcke1 = 0x00003000,
- .dram_sdba2 = 0x00000000,
- .dram_sdodt0 = 0x00003030,
- .dram_sdodt1 = 0x00003030,
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
- .dram_dqm0 = 0x00020030,
- .dram_dqm1 = 0x00020030,
- .dram_dqm2 = 0x00020030,
- .dram_dqm3 = 0x00020030,
- .dram_dqm4 = 0x00020030,
- .dram_dqm5 = 0x00020030,
- .dram_dqm6 = 0x00020030,
- .dram_dqm7 = 0x00020030,
-};
-
-const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
- .grp_ddr_type = 0x000C0000,
- .grp_ddrmode_ctl = 0x00020000,
- .grp_ddrpke = 0x00000000,
- .grp_addds = 0x00000030,
- .grp_ctlds = 0x00000030,
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_b2ds = 0x00000030,
- .grp_b3ds = 0x00000030,
- .grp_b4ds = 0x00000030,
- .grp_b5ds = 0x00000030,
- .grp_b6ds = 0x00000030,
- .grp_b7ds = 0x00000030,
-};
-
-const struct mx6_mmdc_calibration mx6_mmcd_calib = {
- .p0_mpwldectrl0 = 0x001F001F,
- .p0_mpwldectrl1 = 0x001F001F,
- .p1_mpwldectrl0 = 0x00440044,
- .p1_mpwldectrl1 = 0x00440044,
- .p0_mpdgctrl0 = 0x434B0350,
- .p0_mpdgctrl1 = 0x034C0359,
- .p1_mpdgctrl0 = 0x434B0350,
- .p1_mpdgctrl1 = 0x03650348,
- .p0_mprddlctl = 0x4436383B,
- .p1_mprddlctl = 0x39393341,
- .p0_mpwrdlctl = 0x35373933,
- .p1_mpwrdlctl = 0x48254A36,
-};
-
-/* MT41K128M16JT-125 */
-static struct mx6_ddr3_cfg mem_ddr = {
- .mem_speed = 1600,
- .density = 2,
- .width = 16,
- .banks = 8,
- .rowaddr = 14,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-static void ccgr_init(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- writel(0x00C03F3F, &ccm->CCGR0);
- writel(0x0030FC03, &ccm->CCGR1);
- writel(0x0FFFC000, &ccm->CCGR2);
- writel(0x3FF00000, &ccm->CCGR3);
- writel(0x00FFF300, &ccm->CCGR4);
- writel(0x0F0000C3, &ccm->CCGR5);
- writel(0x000003FF, &ccm->CCGR6);
-}
-
-/*
- * This section requires the differentiation between iMX6 Sabre boards, but
- * for now, it will configure only for the mx6q variant.
- */
-static void spl_dram_init(void)
-{
- struct mx6_ddr_sysinfo sysinfo = {
- /* width of data bus:0=16,1=32,2=64 */
- .dsize = 2,
- /* config for full 4GB range so that get_mem_size() works */
- .cs_density = 32, /* 32Gb per CS */
- /* single chip select */
- .ncs = 1,
- .cs1_mirror = 0,
- .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
- .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
- .walat = 1, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
- };
-
- mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
- mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
-}
-
-void board_init_f(ulong dummy)
-{
- /* setup AIPS and disable watchdog */
- arch_cpu_init();
-
- ccgr_init();
- gpr_init();
-
- /* iomux and setup of i2c */
- board_early_init_f();
-
- /* setup GP timer */
- timer_init();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* DDR initialization */
- spl_dram_init();
-
- /* Clear the BSS. */
- memset(__bss_start, 0, __bss_end - __bss_start);
-
- /* load/boot image from boot device */
- board_init_r(NULL, 0);
-}
-
-#endif
diff --git a/configs/zc5202_defconfig b/configs/zc5202_defconfig
deleted file mode 100644
index 321a9351d28e..000000000000
--- a/configs/zc5202_defconfig
+++ /dev/null
@@ -1,62 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_MEMTEST_START=0x10000000
-CONFIG_SYS_MEMTEST_END=0x10800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x0
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
-CONFIG_MX6Q=y
-CONFIG_TARGET_ZC5202=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
-CONFIG_DEFAULT_FDT_FILE="imx6q-zc5202.dtb"
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_SYS_MMC_ENV_PART=2
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_BUS=3
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_MV88E6352_SWITCH=y
-CONFIG_MII=y
-CONFIG_PCI=y
-CONFIG_MXC_UART=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_IMX_THERMAL=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/zc5601_defconfig b/configs/zc5601_defconfig
deleted file mode 100644
index ed6978e32cd9..000000000000
--- a/configs/zc5601_defconfig
+++ /dev/null
@@ -1,60 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_MEMTEST_START=0x10000000
-CONFIG_SYS_MEMTEST_END=0x10800000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x0
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
-CONFIG_MX6Q=y
-CONFIG_TARGET_ZC5601=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
-CONFIG_DEFAULT_FDT_FILE="imx6q-zc5601.dtb"
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_SYS_MMC_ENV_PART=2
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_BUS=3
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_IMX_THERMAL=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/zc5202.h b/include/configs/zc5202.h
deleted file mode 100644
index 7246b9eb6522..000000000000
--- a/include/configs/zc5202.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Stefano Babic <sbabic at denx.de>
- *
- * Configuration settings for the E+L i.MX6Q DO82 board.
- */
-
-#ifndef __EL_ZC5202_H
-#define __EL_ZC5202_H
-
-#define CONFIG_MXC_UART_BASE UART2_BASE
-#define CONSOLE_DEV "ttymxc1"
-#define CONFIG_MMCROOT "/dev/mmcblk0p2"
-
-#include "el6x_common.h"
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE MII100
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
-
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_PCIE_IMX
-
-#endif /*__EL6Q_CONFIG_H */
diff --git a/include/configs/zc5601.h b/include/configs/zc5601.h
deleted file mode 100644
index e4fe7a462d23..000000000000
--- a/include/configs/zc5601.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Stefano Babic <sbabic at denx.de>
- *
- * Configuration settings for the E+L i.MX6Q DO82 board.
- */
-
-#ifndef __EL_ZC5601_H
-#define __EL_ZC5601_H
-
-
-#define CONFIG_MXC_UART_BASE UART2_BASE
-#define CONSOLE_DEV "ttymxc1"
-#define CONFIG_MMCROOT "/dev/mmcblk0p1"
-
-#include "el6x_common.h"
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0x10
-#define CONFIG_FEC_FIXED_SPEED 1000 /* No autoneg, fix Gb */
-
-#endif /*__EL6Q_CONFIG_H */
--
2.17.1
More information about the U-Boot
mailing list