[PATCH 52/57] ppc: Remove MPC8569MDS board
Tom Rini
trini at konsulko.com
Sun Feb 21 02:06:29 CET 2021
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain at nxp.com>
Signed-off-by: Tom Rini <trini at konsulko.com>
---
arch/powerpc/cpu/mpc85xx/Kconfig | 22 +-
arch/powerpc/cpu/mpc85xx/Makefile | 1 -
arch/powerpc/cpu/mpc85xx/mpc8569_serdes.c | 67 ---
arch/powerpc/cpu/mpc85xx/speed.c | 2 +-
arch/powerpc/cpu/mpc85xx/start.S | 33 --
arch/powerpc/include/asm/config_mpc85xx.h | 10 -
arch/powerpc/include/asm/immap_85xx.h | 9 +-
board/freescale/common/pq-mds-pib.c | 15 +-
board/freescale/mpc8569mds/Kconfig | 12 -
board/freescale/mpc8569mds/MAINTAINERS | 7 -
board/freescale/mpc8569mds/Makefile | 11 -
board/freescale/mpc8569mds/README | 77 ---
board/freescale/mpc8569mds/bcsr.c | 50 --
board/freescale/mpc8569mds/bcsr.h | 71 ---
board/freescale/mpc8569mds/ddr.c | 63 ---
board/freescale/mpc8569mds/law.c | 40 --
board/freescale/mpc8569mds/mpc8569mds.c | 590 ----------------------
board/freescale/mpc8569mds/tlb.c | 94 ----
configs/MPC8569MDS_ATM_defconfig | 40 --
configs/MPC8569MDS_defconfig | 39 --
include/configs/MPC8569MDS.h | 489 ------------------
21 files changed, 4 insertions(+), 1738 deletions(-)
delete mode 100644 arch/powerpc/cpu/mpc85xx/mpc8569_serdes.c
delete mode 100644 board/freescale/mpc8569mds/Kconfig
delete mode 100644 board/freescale/mpc8569mds/MAINTAINERS
delete mode 100644 board/freescale/mpc8569mds/Makefile
delete mode 100644 board/freescale/mpc8569mds/README
delete mode 100644 board/freescale/mpc8569mds/bcsr.c
delete mode 100644 board/freescale/mpc8569mds/bcsr.h
delete mode 100644 board/freescale/mpc8569mds/ddr.c
delete mode 100644 board/freescale/mpc8569mds/law.c
delete mode 100644 board/freescale/mpc8569mds/mpc8569mds.c
delete mode 100644 board/freescale/mpc8569mds/tlb.c
delete mode 100644 configs/MPC8569MDS_ATM_defconfig
delete mode 100644 configs/MPC8569MDS_defconfig
delete mode 100644 include/configs/MPC8569MDS.h
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 841c6677e35f..e249ff5926a0 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -64,10 +64,6 @@ config TARGET_MPC8568MDS
bool "Support MPC8568MDS"
select ARCH_MPC8568
-config TARGET_MPC8569MDS
- bool "Support MPC8569MDS"
- select ARCH_MPC8569
-
config TARGET_P1010RDB_PA
bool "Support P1010RDB_PA"
select ARCH_P1010
@@ -443,19 +439,6 @@ config ARCH_MPC8568
select SYS_FSL_SEC_BE
select SYS_FSL_SEC_COMPAT_2
-config ARCH_MPC8569
- bool
- select FSL_LAW
- select SYS_FSL_ERRATUM_A004508
- select SYS_FSL_ERRATUM_A005125
- select FSL_PCIE_RESET
- select SYS_FSL_HAS_DDR3
- select SYS_FSL_HAS_SEC
- select SYS_FSL_SEC_BE
- select SYS_FSL_SEC_COMPAT_2
- select FSL_ELBC
- imply CMD_NAND
-
config ARCH_MPC8572
bool
select FSL_LAW
@@ -1030,7 +1013,6 @@ config SYS_CCSRBAR_DEFAULT
ARCH_MPC8555 || \
ARCH_MPC8560 || \
ARCH_MPC8568 || \
- ARCH_MPC8569 || \
ARCH_MPC8572 || \
ARCH_P1010 || \
ARCH_P1011 || \
@@ -1259,8 +1241,7 @@ config SYS_FSL_NUM_LAWS
ARCH_P2020
default 10 if ARCH_MPC8544 || \
ARCH_MPC8548 || \
- ARCH_MPC8568 || \
- ARCH_MPC8569
+ ARCH_MPC8568
default 8 if ARCH_MPC8540 || \
ARCH_MPC8541 || \
ARCH_MPC8555 || \
@@ -1356,7 +1337,6 @@ source "board/freescale/mpc8541cds/Kconfig"
source "board/freescale/mpc8548cds/Kconfig"
source "board/freescale/mpc8555cds/Kconfig"
source "board/freescale/mpc8568mds/Kconfig"
-source "board/freescale/mpc8569mds/Kconfig"
source "board/freescale/p1010rdb/Kconfig"
source "board/freescale/p1_p2_rdb_pc/Kconfig"
source "board/freescale/p2041rdb/Kconfig"
diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index d8b917f14e32..ed13d5cb56a7 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -64,7 +64,6 @@ obj-$(CONFIG_ARCH_MPC8536) += mpc8536_serdes.o
obj-$(CONFIG_ARCH_MPC8544) += mpc8544_serdes.o
obj-$(CONFIG_ARCH_MPC8548) += mpc8548_serdes.o
obj-$(CONFIG_ARCH_MPC8568) += mpc8568_serdes.o
-obj-$(CONFIG_ARCH_MPC8569) += mpc8569_serdes.o
obj-$(CONFIG_ARCH_MPC8572) += mpc8572_serdes.o
obj-$(CONFIG_ARCH_P1010) += p1010_serdes.o
obj-$(CONFIG_ARCH_P1011) += p1021_serdes.o
diff --git a/arch/powerpc/cpu/mpc85xx/mpc8569_serdes.c b/arch/powerpc/cpu/mpc85xx/mpc8569_serdes.c
deleted file mode 100644
index eb54b8252b20..000000000000
--- a/arch/powerpc/cpu/mpc85xx/mpc8569_serdes.c
+++ /dev/null
@@ -1,67 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Freescale Semiconductor, Inc.
- */
-
-#include <config.h>
-#include <common.h>
-#include <log.h>
-#include <asm/io.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-
-#define SRDS1_MAX_LANES 4
-
-static u32 serdes1_prtcl_map;
-
-static u8 serdes1_cfg_tbl[][SRDS1_MAX_LANES] = {
- [0x0] = {PCIE1, NONE, NONE, NONE},
- [0x1] = {SRIO1, SRIO2, SGMII_TSEC1, SGMII_TSEC2},
- [0x2] = {SRIO1, SRIO2, SGMII_TSEC1, SGMII_TSEC2},
- [0x3] = {SRIO1, SRIO2, NONE, NONE},
- [0x4] = {PCIE1, NONE, SGMII_TSEC1, SGMII_TSEC2},
- [0x5] = {PCIE1, PCIE1, SGMII_TSEC1, SGMII_TSEC2},
- [0x6] = {PCIE1, NONE, SRIO1, SRIO2},
- [0x7] = {PCIE1, PCIE1, SRIO1, SRIO2},
- [0x8] = {PCIE1, PCIE1, SRIO1, SRIO2},
- [0x9] = {SRIO1, SRIO1, SRIO1, SRIO1},
- [0xa] = {SRIO1, SRIO1, SRIO1, SRIO1},
- [0xb] = {SRIO1, SRIO1, SRIO1, SRIO1},
- [0xc] = {PCIE1, SRIO1, SGMII_TSEC1, SGMII_TSEC2},
- [0xf] = {PCIE1, PCIE1, PCIE1, PCIE1},
-};
-
-int is_serdes_configured(enum srds_prtcl prtcl)
-{
- if (!(serdes1_prtcl_map & (1 << NONE)))
- fsl_serdes_init();
-
- return (1 << prtcl) & serdes1_prtcl_map;
-}
-
-void fsl_serdes_init(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 pordevsr = in_be32(&gur->pordevsr);
- u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
- MPC85xx_PORDEVSR_IO_SEL_SHIFT;
- int lane;
-
- if (serdes1_prtcl_map & (1 << NONE))
- return;
-
- debug("PORDEVSR[IO_SEL_SRDS] = %x\n", srds_cfg);
-
- if (srds_cfg >= ARRAY_SIZE(serdes1_cfg_tbl)) {
- printf("Invalid PORDEVSR[IO_SEL_SRDS] = %d\n", srds_cfg);
- return;
- }
-
- for (lane = 0; lane < SRDS1_MAX_LANES; lane++) {
- enum srds_prtcl lane_prtcl = serdes1_cfg_tbl[srds_cfg][lane];
- serdes1_prtcl_map |= (1 << lane_prtcl);
- }
-
- /* Set the first bit to indicate serdes has been initialized */
- serdes1_prtcl_map |= (1 << NONE);
-}
diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index a4623e59634e..864c53ce2ecb 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -629,7 +629,7 @@ int get_clocks(void)
gd->arch.i2c2_clk = gd->arch.i2c1_clk;
#if defined(CONFIG_FSL_ESDHC)
-#if defined(CONFIG_ARCH_MPC8569) || defined(CONFIG_ARCH_P1010)
+#if defined(CONFIG_ARCH_P1010)
gd->arch.sdhc_clk = gd->bus_clk;
#else
gd->arch.sdhc_clk = gd->bus_clk / 2;
diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S
index dd784e7e30b5..f41e82ad189f 100644
--- a/arch/powerpc/cpu/mpc85xx/start.S
+++ b/arch/powerpc/cpu/mpc85xx/start.S
@@ -344,39 +344,6 @@ l2_disabled:
mtspr DBCR0,r0
#endif
-#ifdef CONFIG_ARCH_MPC8569
-#define CONFIG_SYS_LBC_ADDR (CONFIG_SYS_CCSRBAR_DEFAULT + 0x5000)
-#define CONFIG_SYS_LBCR_ADDR (CONFIG_SYS_LBC_ADDR + 0xd0)
-
- /* MPC8569 Rev.0 silcon needs to set bit 13 of LBCR to allow elBC to
- * use address space which is more than 12bits, and it must be done in
- * the 4K boot page. So we set this bit here.
- */
-
- /* create a temp mapping TLB0[0] for LBCR */
- create_tlb0_entry 0, \
- 0, BOOKE_PAGESZ_4K, \
- CONFIG_SYS_LBC_ADDR, MAS2_I|MAS2_G, \
- CONFIG_SYS_LBC_ADDR, MAS3_SW|MAS3_SR, \
- 0, r6
-
- /* Set LBCR register */
- lis r4,CONFIG_SYS_LBCR_ADDR at h
- ori r4,r4,CONFIG_SYS_LBCR_ADDR at l
-
- lis r5,CONFIG_SYS_LBC_LBCR at h
- ori r5,r5,CONFIG_SYS_LBC_LBCR at l
- stw r5,0(r4)
- isync
-
- /* invalidate this temp TLB */
- lis r4,CONFIG_SYS_LBC_ADDR at h
- ori r4,r4,CONFIG_SYS_LBC_ADDR at l
- tlbivax 0,r4
- isync
-
-#endif /* CONFIG_ARCH_MPC8569 */
-
/*
* Search for the TLB that covers the code we're executing, and shrink it
* so that it covers only this 4K page. That will ensure that any other
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index d6e77ab2525e..8487d1aef62a 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -38,16 +38,6 @@
#define CONFIG_SYS_FSL_RMU
#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
-#elif defined(CONFIG_ARCH_MPC8569)
-#define QE_MURAM_SIZE 0x20000UL
-#define MAX_QE_RISC 4
-#define QE_NUM_OF_SNUM 46
-#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1
-#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
-#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
-#define CONFIG_SYS_FSL_RMU
-#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
-
#elif defined(CONFIG_ARCH_P1010)
#define CONFIG_FSL_SDHC_V2_3
#define CONFIG_TSECV2
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index fbe924d4f905..77e0f95cfc3b 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -2201,15 +2201,8 @@ typedef struct ccsr_gur {
u32 gpiocr; /* GPIO control */
#endif
u8 res3[12];
-#if defined(CONFIG_ARCH_MPC8569)
- u32 plppar1; /* Platform port pin assignment 1 */
- u32 plppar2; /* Platform port pin assignment 2 */
- u32 plpdir1; /* Platform port pin direction 1 */
- u32 plpdir2; /* Platform port pin direction 2 */
-#else
u32 gpoutdr; /* General-purpose output data */
u8 res4[12];
-#endif
u32 gpindr; /* General-purpose input data */
u8 res5[12];
u32 pmuxcr; /* Alt. function signal multiplex control */
@@ -2465,7 +2458,7 @@ typedef struct ccsr_gur {
u32 svr; /* System version */
u8 res10[8];
u32 rstcr; /* Reset control */
-#if defined(CONFIG_ARCH_MPC8568) || defined(CONFIG_ARCH_MPC8569)
+#if defined(CONFIG_ARCH_MPC8568)
u8 res11a[76];
par_io_t qe_par_io[7];
u8 res11b[1600];
diff --git a/board/freescale/common/pq-mds-pib.c b/board/freescale/common/pq-mds-pib.c
index ae6603985751..596cd0018c53 100644
--- a/board/freescale/common/pq-mds-pib.c
+++ b/board/freescale/common/pq-mds-pib.c
@@ -63,20 +63,7 @@ int pib_init(void)
#endif
#if defined(CONFIG_PQ_MDS_PIB_ATM)
-#if defined(CONFIG_TARGET_MPC8569MDS)
- val8 = 0;
- i2c_write(0x20, 0x6, 1, &val8, 1);
- i2c_write(0x20, 0x7, 1, &val8, 1);
-
- val8 = 0xdf;
- i2c_write(0x20, 0x2, 1, &val8, 1);
- val8 = 0xf7;
- i2c_write(0x20, 0x3, 1, &val8, 1);
-
- eieio();
-
- printf("QOC3 ATM card on PMC0\n");
-#elif defined(CONFIG_TARGET_MPC832XEMDS)
+#if defined(CONFIG_TARGET_MPC832XEMDS)
val8 = 0;
i2c_write(0x26, 0x7, 1, &val8, 1);
val8 = 0xf7;
diff --git a/board/freescale/mpc8569mds/Kconfig b/board/freescale/mpc8569mds/Kconfig
deleted file mode 100644
index 48718575ff43..000000000000
--- a/board/freescale/mpc8569mds/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8569MDS
-
-config SYS_BOARD
- default "mpc8569mds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8569MDS"
-
-endif
diff --git a/board/freescale/mpc8569mds/MAINTAINERS b/board/freescale/mpc8569mds/MAINTAINERS
deleted file mode 100644
index 9df3f3cca8f1..000000000000
--- a/board/freescale/mpc8569mds/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-MPC8569MDS BOARD
-M: Priyanka Jain <priyanka.jain at nxp.com>
-S: Maintained
-F: board/freescale/mpc8569mds/
-F: include/configs/MPC8569MDS.h
-F: configs/MPC8569MDS_defconfig
-F: configs/MPC8569MDS_ATM_defconfig
diff --git a/board/freescale/mpc8569mds/Makefile b/board/freescale/mpc8569mds/Makefile
deleted file mode 100644
index 45718dfdaecb..000000000000
--- a/board/freescale/mpc8569mds/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2004-2009 Freescale Semiconductor.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-
-obj-y += mpc8569mds.o
-obj-y += bcsr.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
diff --git a/board/freescale/mpc8569mds/README b/board/freescale/mpc8569mds/README
deleted file mode 100644
index 86c3ccde79d2..000000000000
--- a/board/freescale/mpc8569mds/README
+++ /dev/null
@@ -1,77 +0,0 @@
-Overview
---------
-MPC8569MDS is composed of two boards - PB (Processor Board) and PIB (Platform
-I/O Board). The mpc8569 PowerTM processor is mounted on PB board.
-
-Building U-Boot
------------
- make MPC8569MDS_config
- make
-
-Memory Map
-----------
-0x0000_0000 0x7fff_ffff DDR 2G
-0xa000_0000 0xbfff_ffff PCIe MEM 512MB
-0xe000_0000 0xe00f_ffff CCSRBAR 1M
-0xe280_0000 0xe2ff_ffff PCIe I/O 8M
-0xc000_0000 0xdfff_ffff SRIO 512MB
-0xf000_0000 0xf3ff_ffff SDRAM 64MB
-0xf800_0000 0xf800_7fff BCSR 32KB
-0xf800_8000 0xf800_ffff PIB (CS4) 32KB
-0xf801_0000 0xf801_7fff PIB (CS5) 32KB
-0xfe00_0000 0xffff_ffff Flash 32MB
-
-
-Flashing U-Boot Images
----------------
-
-Use the following commands to program U-Boot image into flash:
-
- => tftp 1000000 u-boot.bin
- => protect off all
- => erase fff80000 ffffffff
- => cp.b 1000000 fff80000 80000
-
-
-Setting the correct MAC addresses
------------------------
-The command - "mac", is introduced to set on-board system EEPROM in the format
-defined in board/freescale/common/sys_eeprom.c. we must set all 8 MAC
-addresses for the MPC8569MDS's 8 Ethernet ports and save it by "mac save" when
-we first get the board. The commands are as follows:
- => mac i NXID /* Set NXID to this EEPROM */
- => mac e 01 /* Set Errata, this value is not defined by hardware
- designer, we can set whatever we want */
- => mac n a0 /* Set Serial Number. This is not defined by hardware
- designer, we can set whatever we want */
- => mac date 090512080000 /* Set the date in YYMMDDhhmmss format */
-
- => mac p 8 /* Set the number of mac ports, it should be 8 */
- => mac 0 xx:xx:xx:xx:xx:xx /* xx:xx:xx:xx:xx:xx should be the real mac
- address, you can refer to the value on
- the sticker of the rear side of the board
- */
- .....
- => mac 7 xx:xx:xx:xx:xx:xx
- => mac read
- => mac save
-
-After resetting the board, the ethxaddrs will be filled with the mac addresses
-if such environment variables are blank(never been set before). If the ethxaddr
-has been set but we want to update it, we can use the following commands:
- => setenv ethxaddr /* x = "none",1,2,3,4,5,6,7 */
- => save
- => reset
-
-
-Programming the ucode to flash
----------------------------------
-MPC8569 doesn't have ROM in QE, so we must upload the microcode(ucode) to QE's
-IRAM so that the QE can work. The ucode binary can be downloaded from
-http://opensource.freescale.com/firmware/, and it must be programmed to
-the address 0xfff0000 in the flash. Otherwise, the QE can't work and uboot
-hangs at "Net:"
-
-
-Please note the above two steps(setting mac addresses and programming ucode) are
-very important to get the board booting up and working properly.
diff --git a/board/freescale/mpc8569mds/bcsr.c b/board/freescale/mpc8569mds/bcsr.c
deleted file mode 100644
index 9ed00f6e5b17..000000000000
--- a/board/freescale/mpc8569mds/bcsr.c
+++ /dev/null
@@ -1,50 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2009 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <flash.h>
-#include <asm/io.h>
-
-#include "bcsr.h"
-
-void enable_8569mds_flash_write(void)
-{
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 17), BCSR17_FLASH_nWP);
-}
-
-void disable_8569mds_flash_write(void)
-{
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 17), BCSR17_FLASH_nWP);
-}
-
-void enable_8569mds_qe_uec(void)
-{
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 7),
- BCSR7_UCC1_GETH_EN | BCSR7_UCC1_RGMII_EN);
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 8),
- BCSR8_UCC2_GETH_EN | BCSR8_UCC2_RGMII_EN);
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 9),
- BCSR9_UCC3_GETH_EN | BCSR9_UCC3_RGMII_EN);
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 10),
- BCSR10_UCC4_GETH_EN | BCSR10_UCC4_RGMII_EN);
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
- /* Set UCC1-4 working at RMII mode */
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 7),
- BCSR7_UCC1_GETH_EN | BCSR7_UCC1_RGMII_EN);
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 8),
- BCSR8_UCC2_GETH_EN | BCSR8_UCC2_RGMII_EN);
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 9),
- BCSR9_UCC3_GETH_EN | BCSR9_UCC3_RGMII_EN);
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 10),
- BCSR10_UCC4_GETH_EN | BCSR10_UCC4_RGMII_EN);
- setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 9), BCSR9_UCC3_RMII_EN);
-#endif
-}
-
-void disable_8569mds_brd_eeprom_write_protect(void)
-{
- clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 7), BCSR7_BRD_WRT_PROTECT);
-}
diff --git a/board/freescale/mpc8569mds/bcsr.h b/board/freescale/mpc8569mds/bcsr.h
deleted file mode 100644
index fee0fe7dbce8..000000000000
--- a/board/freescale/mpc8569mds/bcsr.h
+++ /dev/null
@@ -1,71 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2009 Freescale Semiconductor, Inc.
- */
-
-#ifndef __BCSR_H_
-#define __BCSR_H_
-
-#include <common.h>
-
-/* BCSR Bit definitions*/
-/****************************************/
-/* BCSR defines */
-/****************************************/
-#define BCSR6_UPC1_EN 0x80
-#define BCSR6_UPC1_POS_EN 0x40
-#define BCSR6_UPC1_ADDR_EN 0x20
-#define BCSR6_UPC1_DEV2 0x10
-#define BCSR6_SD_CARD_1BIT 0x08
-#define BCSR6_SD_CARD_4BITS 0x04
-#define BCSR6_TDM2G_EN 0x02
-#define BCSR6_UCC7_RMII_EN 0x01
-
-#define BCSR7_UCC1_GETH_EN 0x80
-#define BCSR7_UCC1_RGMII_EN 0x40
-#define BCSR7_UCC1_RTBI_EN 0x20
-#define BCSR7_GETHRST_MRVL 0x04
-#define BCSR7_BRD_WRT_PROTECT 0x02
-
-#define BCSR8_UCC2_GETH_EN 0x80
-#define BCSR8_UCC2_RGMII_EN 0x40
-#define BCSR8_UCC2_RTBI_EN 0x20
-#define BCSR8_UEM_MARVEL_RESET 0x02
-
-#define BCSR9_UCC3_GETH_EN 0x80
-#define BCSR9_UCC3_RGMII_EN 0x40
-#define BCSR9_UCC3_RTBI_EN 0x20
-#define BCSR9_UCC3_RMII_EN 0x10
-#define BCSR9_UCC3_UEM_MICREL 0x01
-
-#define BCSR10_UCC4_GETH_EN 0x80
-#define BCSR10_UCC4_RGMII_EN 0x40
-#define BCSR10_UCC4_RTBI_EN 0x20
-
-#define BCSR11_LED0 0x40
-#define BCSR11_LED1 0x20
-#define BCSR11_LED2 0x10
-
-#define BCSR12_UCC6_RMII_EN 0x20
-#define BCSR12_UCC8_RMII_EN 0x20
-
-#define BCSR15_SMII6_DIS 0x08
-#define BCSR15_SMII8_DIS 0x04
-#define BCSR15_QEUART_EN 0x01
-
-#define BCSR16_UPC1_DEV2 0x02
-
-#define BCSR17_nUSBEN 0x80
-#define BCSR17_nUSBLOWSPD 0x40
-#define BCSR17_USBVCC 0x20
-#define BCSR17_USBMODE 0x10
-#define BCSR17_FLASH_nWP 0x01
-
-/*BCSR Utils functions*/
-
-void enable_8569mds_flash_write(void);
-void disable_8569mds_flash_write(void);
-void enable_8569mds_qe_uec(void);
-void disable_8569mds_brd_eeprom_write_protect(void);
-
-#endif /* __BCSR_H_ */
diff --git a/board/freescale/mpc8569mds/ddr.c b/board/freescale/mpc8569mds/ddr.c
deleted file mode 100644
index d049611e6426..000000000000
--- a/board/freescale/mpc8569mds/ddr.c
+++ /dev/null
@@ -1,63 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2009 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 4;
-
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
- */
- popts->cpo_override = 0xff;
-
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
- */
- popts->write_data_delay = 2;
-
- /*
- * Enable half drive strength
- */
- popts->half_strength_driver_enable = 1;
-
- /* Write leveling override */
- popts->wrlvl_en = 1;
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xa;
- popts->wrlvl_start = 0x4;
-
- /* Rtt and Rtt_W override */
- popts->rtt_override = 1;
- popts->rtt_override_value = DDR3_RTT_60_OHM;
- popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
-}
diff --git a/board/freescale/mpc8569mds/law.c b/board/freescale/mpc8569mds/law.c
deleted file mode 100644
index 35cdd75d6e6a..000000000000
--- a/board/freescale/mpc8569mds/law.c
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- *0) 0x0000_0000 0x7fff_ffff DDR 2G
- *1) 0xa000_0000 0xbfff_ffff PCIe MEM 512MB
- *-) 0xe000_0000 0xe00f_ffff CCSR 1M
- *2) 0xe280_0000 0xe2ff_ffff PCIe I/O 8M
- *3) 0xc000_0000 0xdfff_ffff SRIO 512MB
- *4.a) 0xf000_0000 0xf3ff_ffff SDRAM 64MB
- *4.b) 0xf800_0000 0xf800_7fff BCSR 32KB
- *4.c) 0xf800_8000 0xf800_ffff PIB (CS4) 32KB
- *4.d) 0xf801_0000 0xf801_7fff PIB (CS5) 32KB
- *4.e) 0xfe00_0000 0xffff_ffff Flash 32MB
- *
- *Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- *
- */
-
-struct law_entry law_table[] = {
-#ifndef CONFIG_SPD_EEPROM
- SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_1G, LAW_TRGT_IF_DDR),
-#endif
- SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c
deleted file mode 100644
index 1d2cffbacdf5..000000000000
--- a/board/freescale/mpc8569mds/mpc8569mds.c
+++ /dev/null
@@ -1,590 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009-2010 Freescale Semiconductor.
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt at artesyncp.com>
- */
-
-#include <common.h>
-#include <console.h>
-#include <flash.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <spd_sdram.h>
-#include <i2c.h>
-#include <ioports.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <fsl_esdhc.h>
-#include <phy.h>
-
-#include "bcsr.h"
-#if defined(CONFIG_PQ_MDS_PIB)
-#include "../common/pq-mds-pib.h"
-#endif
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* QE_MUX_MDC */
- {2, 31, 1, 0, 1}, /* QE_MUX_MDC */
-
- /* QE_MUX_MDIO */
- {2, 30, 3, 0, 2}, /* QE_MUX_MDIO */
-
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
- /* UCC_1_RGMII */
- {2, 11, 2, 0, 1}, /* CLK12 */
- {0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */
- {0, 1, 1, 0, 3}, /* ENET1_TXD1_SER1_TXD1 */
- {0, 2, 1, 0, 1}, /* ENET1_TXD2_SER1_TXD2 */
- {0, 3, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */
- {0, 6, 2, 0, 3}, /* ENET1_RXD0_SER1_RXD0 */
- {0, 7, 2, 0, 1}, /* ENET1_RXD1_SER1_RXD1 */
- {0, 8, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */
- {0, 9, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */
- {0, 4, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
- {0, 12, 2, 0, 3}, /* ENET1_RX_DV_SER1_CTS_B */
- {2, 8, 2, 0, 1}, /* ENET1_GRXCLK */
- {2, 20, 1, 0, 2}, /* ENET1_GTXCLK */
-
- /* UCC_2_RGMII */
- {2, 16, 2, 0, 3}, /* CLK17 */
- {0, 14, 1, 0, 2}, /* ENET2_TXD0_SER2_TXD0 */
- {0, 15, 1, 0, 2}, /* ENET2_TXD1_SER2_TXD1 */
- {0, 16, 1, 0, 1}, /* ENET2_TXD2_SER2_TXD2 */
- {0, 17, 1, 0, 1}, /* ENET2_TXD3_SER2_TXD3 */
- {0, 20, 2, 0, 2}, /* ENET2_RXD0_SER2_RXD0 */
- {0, 21, 2, 0, 1}, /* ENET2_RXD1_SER2_RXD1 */
- {0, 22, 2, 0, 1}, /* ENET2_RXD2_SER2_RXD2 */
- {0, 23, 2, 0, 1}, /* ENET2_RXD3_SER2_RXD3 */
- {0, 18, 1, 0, 2}, /* ENET2_TX_EN_SER2_RTS_B */
- {0, 26, 2, 0, 3}, /* ENET2_RX_DV_SER2_CTS_B */
- {2, 3, 2, 0, 1}, /* ENET2_GRXCLK */
- {2, 2, 1, 0, 2}, /* ENET2_GTXCLK */
-
- /* UCC_3_RGMII */
- {2, 11, 2, 0, 1}, /* CLK12 */
- {0, 29, 1, 0, 2}, /* ENET3_TXD0_SER3_TXD0 */
- {0, 30, 1, 0, 3}, /* ENET3_TXD1_SER3_TXD1 */
- {0, 31, 1, 0, 2}, /* ENET3_TXD2_SER3_TXD2 */
- {1, 0, 1, 0, 3}, /* ENET3_TXD3_SER3_TXD3 */
- {1, 3, 2, 0, 3}, /* ENET3_RXD0_SER3_RXD0 */
- {1, 4, 2, 0, 1}, /* ENET3_RXD1_SER3_RXD1 */
- {1, 5, 2, 0, 2}, /* ENET3_RXD2_SER3_RXD2 */
- {1, 6, 2, 0, 3}, /* ENET3_RXD3_SER3_RXD3 */
- {1, 1, 1, 0, 1}, /* ENET3_TX_EN_SER3_RTS_B */
- {1, 9, 2, 0, 3}, /* ENET3_RX_DV_SER3_CTS_B */
- {2, 9, 2, 0, 2}, /* ENET3_GRXCLK */
- {2, 25, 1, 0, 2}, /* ENET3_GTXCLK */
-
- /* UCC_4_RGMII */
- {2, 16, 2, 0, 3}, /* CLK17 */
- {1, 12, 1, 0, 2}, /* ENET4_TXD0_SER4_TXD0 */
- {1, 13, 1, 0, 2}, /* ENET4_TXD1_SER4_TXD1 */
- {1, 14, 1, 0, 1}, /* ENET4_TXD2_SER4_TXD2 */
- {1, 15, 1, 0, 2}, /* ENET4_TXD3_SER4_TXD3 */
- {1, 18, 2, 0, 2}, /* ENET4_RXD0_SER4_RXD0 */
- {1, 19, 2, 0, 1}, /* ENET4_RXD1_SER4_RXD1 */
- {1, 20, 2, 0, 1}, /* ENET4_RXD2_SER4_RXD2 */
- {1, 21, 2, 0, 2}, /* ENET4_RXD3_SER4_RXD3 */
- {1, 16, 1, 0, 2}, /* ENET4_TX_EN_SER4_RTS_B */
- {1, 24, 2, 0, 3}, /* ENET4_RX_DV_SER4_CTS_B */
- {2, 17, 2, 0, 2}, /* ENET4_GRXCLK */
- {2, 24, 1, 0, 2}, /* ENET4_GTXCLK */
-
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
- /* UCC_1_RMII */
- {2, 15, 2, 0, 1}, /* CLK16 */
- {0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */
- {0, 1, 1, 0, 3}, /* ENET1_TXD1_SER1_TXD1 */
- {0, 6, 2, 0, 3}, /* ENET1_RXD0_SER1_RXD0 */
- {0, 7, 2, 0, 1}, /* ENET1_RXD1_SER1_RXD1 */
- {0, 4, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
- {0, 12, 2, 0, 3}, /* ENET1_RX_DV_SER1_CTS_B */
-
- /* UCC_2_RMII */
- {2, 15, 2, 0, 1}, /* CLK16 */
- {0, 14, 1, 0, 2}, /* ENET2_TXD0_SER2_TXD0 */
- {0, 15, 1, 0, 2}, /* ENET2_TXD1_SER2_TXD1 */
- {0, 20, 2, 0, 2}, /* ENET2_RXD0_SER2_RXD0 */
- {0, 21, 2, 0, 1}, /* ENET2_RXD1_SER2_RXD1 */
- {0, 18, 1, 0, 2}, /* ENET2_TX_EN_SER2_RTS_B */
- {0, 26, 2, 0, 3}, /* ENET2_RX_DV_SER2_CTS_B */
-
- /* UCC_3_RMII */
- {2, 15, 2, 0, 1}, /* CLK16 */
- {0, 29, 1, 0, 2}, /* ENET3_TXD0_SER3_TXD0 */
- {0, 30, 1, 0, 3}, /* ENET3_TXD1_SER3_TXD1 */
- {1, 3, 2, 0, 3}, /* ENET3_RXD0_SER3_RXD0 */
- {1, 4, 2, 0, 1}, /* ENET3_RXD1_SER3_RXD1 */
- {1, 1, 1, 0, 1}, /* ENET3_TX_EN_SER3_RTS_B */
- {1, 9, 2, 0, 3}, /* ENET3_RX_DV_SER3_CTS_B */
-
- /* UCC_4_RMII */
- {2, 15, 2, 0, 1}, /* CLK16 */
- {1, 12, 1, 0, 2}, /* ENET4_TXD0_SER4_TXD0 */
- {1, 13, 1, 0, 2}, /* ENET4_TXD1_SER4_TXD1 */
- {1, 18, 2, 0, 2}, /* ENET4_RXD0_SER4_RXD0 */
- {1, 19, 2, 0, 1}, /* ENET4_RXD1_SER4_RXD1 */
- {1, 16, 1, 0, 2}, /* ENET4_TX_EN_SER4_RTS_B */
- {1, 24, 2, 0, 3}, /* ENET4_RX_DV_SER4_CTS_B */
-#endif
-
- /* UART1 is muxed with QE PortF bit [9-12].*/
- {5, 12, 2, 0, 3}, /* UART1_SIN */
- {5, 9, 1, 0, 3}, /* UART1_SOUT */
- {5, 10, 2, 0, 3}, /* UART1_CTS_B */
- {5, 11, 1, 0, 2}, /* UART1_RTS_B */
-
- /* QE UART */
- {0, 19, 1, 0, 2}, /* QEUART_TX */
- {1, 17, 2, 0, 3}, /* QEUART_RX */
- {0, 25, 1, 0, 1}, /* QEUART_RTS */
- {1, 23, 2, 0, 1}, /* QEUART_CTS */
-
- /* QE USB */
- {5, 3, 1, 0, 1}, /* USB_OE */
- {5, 4, 1, 0, 2}, /* USB_TP */
- {5, 5, 1, 0, 2}, /* USB_TN */
- {5, 6, 2, 0, 2}, /* USB_RP */
- {5, 7, 2, 0, 1}, /* USB_RX */
- {5, 8, 2, 0, 1}, /* USB_RN */
- {2, 4, 2, 0, 2}, /* CLK5 */
-
- /* SPI Flash, M25P40 */
- {4, 27, 3, 0, 1}, /* SPI_MOSI */
- {4, 28, 3, 0, 1}, /* SPI_MISO */
- {4, 29, 3, 0, 1}, /* SPI_CLK */
- {4, 30, 1, 0, 0}, /* SPI_SEL, GPIO */
-
- {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */
-};
-
-void local_bus_init(void);
-
-int board_early_init_f (void)
-{
- /*
- * Initialize local bus.
- */
- local_bus_init ();
-
- enable_8569mds_flash_write();
-
-#ifdef CONFIG_QE
- enable_8569mds_qe_uec();
-#endif
-
-#if CONFIG_SYS_I2C2_OFFSET
- /* Enable I2C2 signals instead of SD signals */
- volatile struct ccsr_gur *gur;
- gur = (struct ccsr_gur *)(CONFIG_SYS_IMMR + 0xe0000);
- gur->plppar1 &= ~PLPPAR1_I2C_BIT_MASK;
- gur->plppar1 |= PLPPAR1_I2C2_VAL;
- gur->plpdir1 &= ~PLPDIR1_I2C_BIT_MASK;
- gur->plpdir1 |= PLPDIR1_I2C2_VAL;
-
- disable_8569mds_brd_eeprom_write_protect();
-#endif
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_NAND_BASE;
- const u8 flash_esel = 0;
-
- /*
- * Remap Boot flash to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* invalidate existing TLB entry for flash */
- disable_tlb(flash_esel);
-
- set_tlb(1, flashbase, CONFIG_SYS_NAND_BASE, /* tlb, epn, rpn */
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
- 0, flash_esel, /* ts, esel */
- BOOKE_PAGESZ_64M, 1); /* tsize, iprot */
-
- return 0;
-}
-
-int checkboard (void)
-{
- printf ("Board: 8569 MDS\n");
-
- return 0;
-}
-
-#if !defined(CONFIG_SPD_EEPROM)
-phys_size_t fixed_sdram(void)
-{
- struct ccsr_ddr __iomem *ddr =
- (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
- uint d_init;
-
- out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
- out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
- out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
- out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
- out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
- out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
- out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
- out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_SDRAM_CFG_2);
- out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_SDRAM_MODE);
- out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_SDRAM_MODE_2);
- out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_SDRAM_INTERVAL);
- out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
- out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
- out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
- out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
- out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
- out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
- out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_SDRAM_CFG_2);
-#if defined (CONFIG_DDR_ECC)
- out_be32(&ddr->err_int_en, CONFIG_SYS_DDR_ERR_INT_EN);
- out_be32(&ddr->err_disable, CONFIG_SYS_DDR_ERR_DIS);
- out_be32(&ddr->err_sbe, CONFIG_SYS_DDR_SBE);
-#endif
- udelay(500);
-
- out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
-#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- d_init = 1;
- debug("DDR - 1st controller: memory initializing\n");
- /*
- * Poll until memory is initialized.
- * 512 Meg at 400 might hit this 200 times or so.
- */
- while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
- udelay(1000);
- }
- debug("DDR: memory initialized\n\n");
- udelay(500);
-#endif
- return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-}
-#endif
-
-/*
- * Initialize Local Bus
- */
-void
-local_bus_init(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
- uint clkdiv;
- sys_info_t sysinfo;
-
- get_sys_info(&sysinfo);
- clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
-
- out_be32(&gur->lbiuiplldcr1, 0x00078080);
- if (clkdiv == 16)
- out_be32(&gur->lbiuiplldcr0, 0x7c0f1bf0);
- else if (clkdiv == 8)
- out_be32(&gur->lbiuiplldcr0, 0x6c0f1bf0);
- else if (clkdiv == 4)
- out_be32(&gur->lbiuiplldcr0, 0x5c0f1bf0);
-
- out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000);
-}
-
-static void fdt_board_disable_serial(void *blob, struct bd_info *bd,
- const char *alias)
-{
- const char *status = "disabled";
- int off;
- int err;
-
- off = fdt_path_offset(blob, alias);
- if (off < 0) {
- printf("WARNING: could not find %s alias: %s.\n", alias,
- fdt_strerror(off));
- return;
- }
-
- err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
- if (err) {
- printf("WARNING: could not set status for serial0: %s.\n",
- fdt_strerror(err));
- return;
- }
-}
-
-/*
- * Because of an erratum in prototype boards it is impossible to use eSDHC
- * without disabling UART0 (which makes it quite easy to 'brick' the board
- * by simply issung 'setenv hwconfig esdhc', and not able to interact with
- * U-Boot anylonger).
- *
- * So, but default we assume that the board is a prototype, which is a most
- * safe assumption. There is no way to determine board revision from a
- * register, so we use hwconfig.
- */
-
-static int prototype_board(void)
-{
- if (hwconfig_subarg("board", "rev", NULL))
- return hwconfig_subarg_cmp("board", "rev", "prototype");
- return 1;
-}
-
-static int esdhc_disables_uart0(void)
-{
- return prototype_board() ||
- hwconfig_subarg_cmp("esdhc", "mode", "4-bits");
-}
-
-static void fdt_board_fixup_qe_uart(void *blob, struct bd_info *bd)
-{
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
- const char *devtype = "serial";
- const char *compat = "ucc_uart";
- const char *clk = "brg9";
- u32 portnum = 0;
- int off = -1;
-
- if (!hwconfig("qe_uart"))
- return;
-
- if (hwconfig("esdhc") && esdhc_disables_uart0()) {
- printf("QE UART: won't enable with esdhc.\n");
- return;
- }
-
- fdt_board_disable_serial(blob, bd, "serial1");
-
- while (1) {
- const u32 *idx;
- int len;
-
- off = fdt_node_offset_by_compatible(blob, off, "ucc_geth");
- if (off < 0) {
- printf("WARNING: unable to fixup device tree for "
- "QE UART\n");
- return;
- }
-
- idx = fdt_getprop(blob, off, "cell-index", &len);
- if (!idx || len != sizeof(*idx) || *idx != fdt32_to_cpu(2))
- continue;
- break;
- }
-
- fdt_setprop(blob, off, "device_type", devtype, strlen(devtype) + 1);
- fdt_setprop(blob, off, "compatible", compat, strlen(compat) + 1);
- fdt_setprop(blob, off, "tx-clock-name", clk, strlen(clk) + 1);
- fdt_setprop(blob, off, "rx-clock-name", clk, strlen(clk) + 1);
- fdt_setprop(blob, off, "port-number", &portnum, sizeof(portnum));
-
- setbits_8(&bcsr[15], BCSR15_QEUART_EN);
-}
-
-#ifdef CONFIG_FSL_ESDHC
-
-int board_mmc_init(struct bd_info *bd)
-{
- struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
- u8 bcsr6 = BCSR6_SD_CARD_1BIT;
-
- if (!hwconfig("esdhc"))
- return 0;
-
- printf("Enabling eSDHC...\n"
- " For eSDHC to function, I2C2 ");
- if (esdhc_disables_uart0()) {
- printf("and UART0 should be disabled.\n");
- printf(" Redirecting stderr, stdout and stdin to UART1...\n");
- console_assign(stderr, "eserial1");
- console_assign(stdout, "eserial1");
- console_assign(stdin, "eserial1");
- printf("Switched to UART1 (initial log has been printed to "
- "UART0).\n");
-
- clrsetbits_be32(&gur->plppar1, PLPPAR1_UART0_BIT_MASK,
- PLPPAR1_ESDHC_4BITS_VAL);
- clrsetbits_be32(&gur->plpdir1, PLPDIR1_UART0_BIT_MASK,
- PLPDIR1_ESDHC_4BITS_VAL);
- bcsr6 |= BCSR6_SD_CARD_4BITS;
- } else {
- printf("should be disabled.\n");
- }
-
- /* Assign I2C2 signals to eSDHC. */
- clrsetbits_be32(&gur->plppar1, PLPPAR1_I2C_BIT_MASK,
- PLPPAR1_ESDHC_VAL);
- clrsetbits_be32(&gur->plpdir1, PLPDIR1_I2C_BIT_MASK,
- PLPDIR1_ESDHC_VAL);
-
- /* Mux I2C2 (and optionally UART0) signals to eSDHC. */
- setbits_8(&bcsr[6], bcsr6);
-
- return fsl_esdhc_mmc_init(bd);
-}
-
-static void fdt_board_fixup_esdhc(void *blob, struct bd_info *bd)
-{
- const char *status = "disabled";
- int off = -1;
-
- if (!hwconfig("esdhc"))
- return;
-
- if (esdhc_disables_uart0())
- fdt_board_disable_serial(blob, bd, "serial0");
-
- while (1) {
- const u32 *idx;
- int len;
-
- off = fdt_node_offset_by_compatible(blob, off, "fsl-i2c");
- if (off < 0)
- break;
-
- idx = fdt_getprop(blob, off, "cell-index", &len);
- if (!idx || len != sizeof(*idx))
- continue;
-
- if (*idx == 1) {
- fdt_setprop(blob, off, "status", status,
- strlen(status) + 1);
- break;
- }
- }
-
- if (hwconfig_subarg_cmp("esdhc", "mode", "4-bits")) {
- off = fdt_node_offset_by_compatible(blob, -1, "fsl,esdhc");
- if (off < 0) {
- printf("WARNING: could not find esdhc node\n");
- return;
- }
- fdt_delprop(blob, off, "sdhci,1-bit-only");
- }
-}
-#else
-static inline void fdt_board_fixup_esdhc(void *blob, struct bd_info *bd) {}
-#endif
-
-static void fdt_board_fixup_qe_usb(void *blob, struct bd_info *bd)
-{
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
-
- if (hwconfig_subarg_cmp("qe_usb", "speed", "low"))
- clrbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
- else
- setbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
-
- if (hwconfig_subarg_cmp("qe_usb", "mode", "peripheral")) {
- clrbits_8(&bcsr[17], BCSR17_USBVCC);
- clrbits_8(&bcsr[17], BCSR17_USBMODE);
- do_fixup_by_compat(blob, "fsl,mpc8569-qe-usb", "mode",
- "peripheral", sizeof("peripheral"), 1);
- } else {
- setbits_8(&bcsr[17], BCSR17_USBVCC);
- setbits_8(&bcsr[17], BCSR17_USBMODE);
- }
-
- clrbits_8(&bcsr[17], BCSR17_nUSBEN);
-}
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
-#if defined(CONFIG_PQ_MDS_PIB)
- pib_init();
-#endif
-
- fsl_pcie_init_board(0);
-}
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-#if defined(CONFIG_SYS_UCC_RMII_MODE)
- int nodeoff, off, err;
- unsigned int val;
- const u32 *ph;
- const u32 *index;
-
- /* fixup device tree for supporting rmii mode */
- nodeoff = -1;
- while ((nodeoff = fdt_node_offset_by_compatible(blob, nodeoff,
- "ucc_geth")) >= 0) {
- err = fdt_setprop_string(blob, nodeoff, "tx-clock-name",
- "clk16");
- if (err < 0) {
- printf("WARNING: could not set tx-clock-name %s.\n",
- fdt_strerror(err));
- break;
- }
-
- err = fdt_fixup_phy_connection(blob, nodeoff,
- PHY_INTERFACE_MODE_RMII);
-
- if (err < 0) {
- printf("WARNING: could not set phy-connection-type "
- "%s.\n", fdt_strerror(err));
- break;
- }
-
- index = fdt_getprop(blob, nodeoff, "cell-index", 0);
- if (index == NULL) {
- printf("WARNING: could not get cell-index of ucc\n");
- break;
- }
-
- ph = fdt_getprop(blob, nodeoff, "phy-handle", 0);
- if (ph == NULL) {
- printf("WARNING: could not get phy-handle of ucc\n");
- break;
- }
-
- off = fdt_node_offset_by_phandle(blob, *ph);
- if (off < 0) {
- printf("WARNING: could not get phy node %s.\n",
- fdt_strerror(err));
- break;
- }
-
- val = 0x7 + *index; /* RMII phy address starts from 0x8 */
-
- err = fdt_setprop(blob, off, "reg", &val, sizeof(u32));
- if (err < 0) {
- printf("WARNING: could not set reg for phy-handle "
- "%s.\n", fdt_strerror(err));
- break;
- }
- }
-#endif
- ft_cpu_setup(blob, bd);
-
- FT_FSL_PCI_SETUP;
-
- fdt_board_fixup_esdhc(blob, bd);
- fdt_board_fixup_qe_uart(blob, bd);
- fdt_board_fixup_qe_usb(blob, bd);
-
- return 0;
-}
-#endif
diff --git a/board/freescale/mpc8569mds/tlb.c b/board/freescale/mpc8569mds/tlb.c
deleted file mode 100644
index fdbac5498474..000000000000
--- a/board/freescale/mpc8569mds/tlb.c
+++ /dev/null
@@ -1,94 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 Initializations */
- /*
- * TLBe 0: 64M write-through, guarded
- * Out of reset this entry is only 4K.
- * 0xfc000000 32MB NAND FLASH (CS3)
- * 0xfe000000 32MB NOR FLASH (CS0)
- */
-#ifdef CONFIG_NAND_SPL
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_1M, 1),
-#else
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 0, BOOKE_PAGESZ_64M, 1),
-#endif
- /*
- * TLBe 1: 256KB Non-cacheable, guarded
- * 0xf8000000 32K BCSR
- * 0xf8008000 32K PIB (CS4)
- * 0xf8010000 32K PIB (CS5)
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_256K, 1),
-
- /*
- * TLBe 2: 256M Non-cacheable, guarded
- * 0xa00000000 256M PCIe MEM (lower half)
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
- /*
- * TLBe 3: 256M Non-cacheable, guarded
- * 0xb00000000 256M PCIe MEM (higher half)
- */
- SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000),
- (CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000),
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_256M, 1),
-
- /*
- * TLBe 4: 64M Non-cacheable, guarded
- * 0xe000_0000 1M CCSRBAR
- * 0xe280_0000 8M PCIe IO
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_64M, 1),
-
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
- /* *I*G - L2SRAM */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256K, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
- CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/MPC8569MDS_ATM_defconfig b/configs/MPC8569MDS_ATM_defconfig
deleted file mode 100644
index b1f4789a926a..000000000000
--- a/configs/MPC8569MDS_ATM_defconfig
+++ /dev/null
@@ -1,40 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8569MDS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="ATM"
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFF60000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_E1000=y
-CONFIG_QE=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/MPC8569MDS_defconfig b/configs/MPC8569MDS_defconfig
deleted file mode 100644
index 1f0f3dcceb12..000000000000
--- a/configs/MPC8569MDS_defconfig
+++ /dev/null
@@ -1,39 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8569MDS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFF60000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_E1000=y
-CONFIG_QE=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
deleted file mode 100644
index f50f53ec3fce..000000000000
--- a/include/configs/MPC8569MDS.h
+++ /dev/null
@@ -1,489 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- */
-
-/*
- * mpc8569mds board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1 /* SRIO port 1 */
-
-#define CONFIG_PCIE1 1 /* PCIE controller */
-#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-/* Replace a call to get_clock_freq (after it is implemented)*/
-#define CONFIG_SYS_CLK_FREQ 66666666
-#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
-
-#ifdef CONFIG_ATM
-#define CONFIG_PQ_MDS_PIB
-#define CONFIG_PQ_MDS_PIB_ATM
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_HWCONFIG
-
-/*
- * Config the L2 Cache as L2 SRAM
- */
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR 0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-#if defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
- /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
-
-/* These are used when DDR doesn't use SPD. */
-#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-#define CONFIG_SYS_DDR_TIMING_3 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0 0x00330004
-#define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644
-#define CONFIG_SYS_DDR_TIMING_2 0x002888D0
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000
-#define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040
-#define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521
-#define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000
-#define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000
-#define CONFIG_SYS_DDR_TIMING_4 0x00220001
-#define CONFIG_SYS_DDR_TIMING_5 0x03402400
-#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604
-#define CONFIG_SYS_DDR_CDR_1 0x80040000
-#define CONFIG_SYS_DDR_CDR_2 0x00000000
-#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
-#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL2 0x24400000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00010000
-
-/*
- * Local Bus Definitions
- */
-
-#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_BCSR_BASE 0xf8000000
-#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
-
-/*Chip select 0 - Flash*/
-#define CONFIG_FLASH_BR_PRELIM 0xfe000801
-#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7
-
-/*Chip select 1 - BCSR*/
-#define CONFIG_SYS_BR1_PRELIM 0xf8000801
-#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7
-
-/*Chip select 4 - PIB*/
-#define CONFIG_SYS_BR4_PRELIM 0xf8008801
-#define CONFIG_SYS_OR4_PRELIM 0xffffe9f7
-
-/*Chip select 5 - PIB*/
-#define CONFIG_SYS_BR5_PRELIM 0xf8010801
-#define CONFIG_SYS_OR5_PRELIM 0xffffe9f7
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#undef CONFIG_SYS_RAMBOOT
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Chip select 3 - NAND */
-#ifndef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xFC000000
-#else
-#define CONFIG_SYS_NAND_BASE 0xFFF00000
-#endif
-
-/* NAND boot: 4K NAND loader config */
-#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
-#define CONFIG_SYS_NAND_U_BOOT_START \
- (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
-
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_FSL_ELBC 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 1
-
-#define PLPPAR1_I2C_BIT_MASK 0x0000000F
-#define PLPPAR1_I2C2_VAL 0x00000000
-#define PLPPAR1_ESDHC_VAL 0x0000000A
-#define PLPDIR1_I2C_BIT_MASK 0x0000000F
-#define PLPDIR1_I2C2_VAL 0x0000000F
-#define PLPDIR1_ESDHC_VAL 0x00000006
-#define PLPPAR1_UART0_BIT_MASK 0x00000fc0
-#define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80
-#define PLPDIR1_UART0_BIT_MASK 0x00000fc0
-#define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80
-
-/*
- * General PCI
- * Memory Addresses are mapped 1-1. I/O is mapped from 0
- */
-#define CONFIG_SYS_PCIE1_NAME "Slot"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-#define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS
-#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-
-#ifdef CONFIG_QE
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */
-#undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */
-
-#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-#define CONFIG_PHY_MODE_NEED_CHANGE
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define CONFIG_HAS_ETH0
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12
-#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif /* CONFIG_SYS_UCC_RGMII_MODE */
-#endif /* CONFIG_UEC_ETH1 */
-
-#define CONFIG_UEC_ETH2 /* GETH2 */
-#define CONFIG_HAS_ETH1
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */
-#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
-#endif /* CONFIG_SYS_UCC_RGMII_MODE */
-#endif /* CONFIG_UEC_ETH2 */
-
-#define CONFIG_UEC_ETH3 /* GETH3 */
-#define CONFIG_HAS_ETH2
-
-#ifdef CONFIG_UEC_ETH3
-#define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */
-#define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
-#define CONFIG_SYS_UEC3_TX_CLK QE_CLK12
-#define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC3_PHY_ADDR 2
-#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
-#define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */
-#define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */
-#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
-#endif /* CONFIG_SYS_UCC_RGMII_MODE */
-#endif /* CONFIG_UEC_ETH3 */
-
-#define CONFIG_UEC_ETH4 /* GETH4 */
-#define CONFIG_HAS_ETH3
-
-#ifdef CONFIG_UEC_ETH4
-#define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE
-#if defined(CONFIG_SYS_UCC_RGMII_MODE)
-#define CONFIG_SYS_UEC4_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC4_PHY_ADDR 3
-#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
-#elif defined(CONFIG_SYS_UCC_RMII_MODE)
-#define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */
-#define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */
-#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
-#endif /* CONFIG_SYS_UCC_RGMII_MODE */
-#endif /* CONFIG_UEC_ETH4 */
-
-#undef CONFIG_UEC_ETH6 /* GETH6 */
-#define CONFIG_HAS_ETH5
-
-#ifdef CONFIG_UEC_ETH6
-#define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */
-#define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC6_PHY_ADDR 4
-#define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
-#define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
-#endif /* CONFIG_UEC_ETH6 */
-
-#undef CONFIG_UEC_ETH8 /* GETH8 */
-#define CONFIG_HAS_ETH7
-
-#ifdef CONFIG_UEC_ETH8
-#define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */
-#define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC8_PHY_ADDR 6
-#define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
-#define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
-#endif /* CONFIG_UEC_ETH8 */
-
-#endif /* CONFIG_QE */
-
-#if defined(CONFIG_PCI)
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-#endif /* CONFIG_PCI */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FW_ADDR 0xfff00000
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC_PIN_MUX
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
- /* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_HOSTNAME "mpc8569mds"
-#define CONFIG_ROOTPATH "/nfsroot"
-#define CONFIG_BOOTFILE "your.uImage"
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=600000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=your.fdt.dtb\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs\0" \
- "ramargs=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs\0" \
-
-#define CONFIG_NFSBOOTCOMMAND \
- "run nfsargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "run ramargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
--
2.17.1
More information about the U-Boot
mailing list