[PATCH] stm32mp1: add pull-up for gpio button PA13 and PA14

[Patrick Delaunay]

When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.

So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.

Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
---

 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 4 ++--
 arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 4 ++--
 board/st/stm32mp1/stm32mp1.c             | 2 ++
 3 files changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
index 6787619290..d44da7566f 100644
--- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
@@ -18,8 +18,8 @@
 		u-boot,error-led = "error";
 		u-boot,mmc-env-partition = "ssbl";
 		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
-		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
-		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+		st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	};
 
 	firmware {
diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
index f3002e995b..3b94218b2f 100644
--- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
+++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
@@ -18,8 +18,8 @@
 		u-boot,boot-led = "heartbeat";
 		u-boot,error-led = "error";
 		u-boot,mmc-env-partition = "ssbl";
-		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
-		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+		st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	};
 
 	firmware {
diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
index 18b8870269..e1796e7e31 100644
--- a/board/st/stm32mp1/stm32mp1.c
+++ b/board/st/stm32mp1/stm32mp1.c
@@ -155,6 +155,7 @@ static void board_key_check(void)
 					       &gpio, GPIOD_IS_IN)) {
 			log_debug("could not find a /config/st,fastboot-gpios\n");
 		} else {
+			udelay(20);
 			if (dm_gpio_get_value(&gpio)) {
 				log_notice("Fastboot key pressed, ");
 				boot_mode = BOOT_FASTBOOT;
@@ -168,6 +169,7 @@ static void board_key_check(void)
 					       &gpio, GPIOD_IS_IN)) {
 			log_debug("could not find a /config/st,stm32prog-gpios\n");
 		} else {
+			udelay(20);
 			if (dm_gpio_get_value(&gpio)) {
 				log_notice("STM32Programmer key pressed, ");
 				boot_mode = BOOT_STM32PROG;
-- 
2.25.1