[Patch V3 44/44] arm: imx: add i.MX8ULP EVK support

[sbabic at denx.de]

> From: Peng Fan <peng.fan at nxp.com>
> Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
> Log as below: I would keep some debug info for now, and after we move
> to be stable and production launch, we could drop that.
> U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
> Normal Boot
> upower_init: soc_id=48
> upower_init: version:11.11.6
> upower_init: start uPower RAM service
> user_upwr_rdy_callb: soc=b
> user_upwr_rdy_callb: RAM version:12.6
> Turn on switches ok
> Turn on memories ok
> Clear DDR retention ok
> Poll for freq_chg_req on SIM register and change to F1 frequency.
> Poll for freq_chg_req on SIM register and change to F0 frequency.
> Poll for freq_chg_req on SIM register and change to F1 frequency.
> Poll for freq_chg_req on SIM register and change to F2 frequency.
> Poll for freq_chg_req on SIM register and change to F1 frequency.
> Poll for freq_chg_req on SIM register and change to F2 frequency.
> complete
> De-Skew PLL is locked and ready
> WDT:   Not found!
> Trying to boot from BOOTROM
> image offset 0x8000, pagesize 0x200, ivt offset 0x0
> Load image from 0x3a800 by ROM_API
> NOTICE:  BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94-dirty
> NOTICE:  BL31: Built : 01:56:58, Jun 29 2021
> NOTICE:  upower_init: start uPower RAM service
> NOTICE:  user_upwr_rdy_callb: soc=b
> NOTICE:  user_upwr_rdy_callb: RAM version:12.6
> U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
> CPU:   Freescale i.MX8ULP rev1.0 at 744 MHz
> Reset cause: POR
> Boot mode: Single boot
> Model: FSL i.MX8ULP EVK
> DRAM:  2 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 2
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> In:    serial at 293a0000
> Out:   serial at 293a0000
> Err:   serial at 293a0000
> Net:
> Warning: ethernet at 29950000 (eth0) using random MAC address - 96:35:88:62:e0:44
> eth0: ethernet at 29950000
> Hit any key to stop autoboot:  0
> Signed-off-by: Peng Fan <peng.fan at nxp.com>
Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================