[PATCH v3 1/6] net: eth-phy: add support of device tree configuration for gpio reset
Ramon Fried
rfried.dev at gmail.com
Thu Jul 22 21:06:40 CEST 2021
On Tue, Jul 20, 2021 at 9:10 PM Patrick Delaunay
<patrick.delaunay at foss.st.com> wrote:
>
> The gpio reset and the assert or deassert delay are defined in generic
> binding of the ethernet phy in Linux:
> Documentation/devicetree/bindings/net/ethernet-phy.yaml
>
> reset-gpios:
> maxItems: 1
> description:
> The GPIO phandle and specifier for the PHY reset signal.
>
> reset-assert-us:
> description:
> Delay after the reset was asserted in microseconds. If this
> property is missing the delay will be skipped.
>
> reset-deassert-us:
> description:
> Delay after the reset was deasserted in microseconds. If
> this property is missing the delay will be skipped.
>
> See also U-Boot: doc/device-tree-bindings/net/phy.txt
>
> This patch adds the parsing of this common DT properties in the
> u-class "eth_phy_generic", used by default in the associated driver
> "eth_phy_generic_drv"
>
> This parsing function eth_phy_of_to_plat can be reused by other
> ethernet phy drivers for this uclass UCLASS_ETH_PHY.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
> ---
>
> Changes in v3:
> - allow compilation without DM_GPIO
>
> Changes in v2:
> - Update eth-phy driver (NEW)
>
> drivers/net/eth-phy-uclass.c | 56 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 56 insertions(+)
>
> diff --git a/drivers/net/eth-phy-uclass.c b/drivers/net/eth-phy-uclass.c
> index 07aebd935e..7abed14392 100644
> --- a/drivers/net/eth-phy-uclass.c
> +++ b/drivers/net/eth-phy-uclass.c
> @@ -6,12 +6,17 @@
> #include <common.h>
> #include <dm.h>
> #include <net.h>
> +#include <asm-generic/gpio.h>
> #include <dm/device-internal.h>
> #include <dm/uclass-internal.h>
> #include <dm/lists.h>
> +#include <linux/delay.h>
>
> struct eth_phy_device_priv {
> struct mii_dev *mdio_bus;
> + struct gpio_desc reset_gpio;
> + u32 reset_assert_delay;
> + u32 reset_deassert_delay;
> };
>
> int eth_phy_binds_nodes(struct udevice *eth_dev)
> @@ -110,13 +115,64 @@ int eth_phy_get_addr(struct udevice *dev)
> return reg;
> }
>
> +/* parsing generic properties of devicetree/bindings/net/ethernet-phy.yaml */
> +static int eth_phy_of_to_plat(struct udevice *dev)
> +{
> + struct eth_phy_device_priv *uc_priv = dev_get_uclass_priv(dev);
> + int ret;
> +
> + if (!CONFIG_IS_ENABLED(DM_GPIO))
> + return 0;
> +
> + /* search "reset-gpios" in phy node */
> + ret = gpio_request_by_name(dev, "reset-gpios", 0,
> + &uc_priv->reset_gpio,
> + GPIOD_IS_OUT);
> + if (ret != -ENOENT)
> + return ret;
> +
> + uc_priv->reset_assert_delay = dev_read_u32_default(dev, "reset-assert-us", 0);
> + uc_priv->reset_deassert_delay = dev_read_u32_default(dev, "reset-deassert-us", 0);
> +
> + return 0;
> +}
> +
> +void eth_phy_reset(struct udevice *dev, int value)
> +{
> + struct eth_phy_device_priv *uc_priv = dev_get_uclass_priv(dev);
> + u32 delay;
> +
> + if (!CONFIG_IS_ENABLED(DM_GPIO))
> + return;
> +
> + if (!dm_gpio_is_valid(&uc_priv->reset_gpio))
> + return;
> +
> + dm_gpio_set_value(&uc_priv->reset_gpio, value);
> +
> + delay = value ? uc_priv->reset_assert_delay : uc_priv->reset_deassert_delay;
> + if (delay)
> + udelay(delay);
> +}
> +
> +static int eth_phy_pre_probe(struct udevice *dev)
> +{
> + /* Assert and deassert the reset signal */
> + eth_phy_reset(dev, 1);
> + eth_phy_reset(dev, 0);
> +
> + return 0;
> +}
> +
> UCLASS_DRIVER(eth_phy_generic) = {
> .id = UCLASS_ETH_PHY,
> .name = "eth_phy_generic",
> .per_device_auto = sizeof(struct eth_phy_device_priv),
> + .pre_probe = eth_phy_pre_probe,
> };
>
> U_BOOT_DRIVER(eth_phy_generic_drv) = {
> .name = "eth_phy_generic_drv",
> .id = UCLASS_ETH_PHY,
> + .of_to_plat = eth_phy_of_to_plat,
> };
> --
> 2.25.1
>
Applied to u-boot-net/network-master
Thanks,
Ramon.
More information about the U-Boot
mailing list