[PATCH 06/10] arm: dts: k3-am642-*-evm: Add USB support

Aswath Govindraju a-govindraju at ti.com
Tue Jun 1 17:13:46 CEST 2021


AM64 EVM board has a micro USB 2.0 AB connector and the USB0_VBUS is
connected with a resistor divider in between. USB0_DRVVBUS pin is muxed
between USB0_DRVVBUS and GPIO1_79 signals.

Add the corresponding properties and set the pinmux mode for USB subsystem
in the evm dts file.

Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
---
 arch/arm/dts/k3-am642-evm.dts    | 18 ++++++++++++++++++
 arch/arm/dts/k3-am642-r5-evm.dts | 18 ++++++++++++++++++
 2 files changed, 36 insertions(+)

diff --git a/arch/arm/dts/k3-am642-evm.dts b/arch/arm/dts/k3-am642-evm.dts
index dc3482bea433..3a505d22c635 100644
--- a/arch/arm/dts/k3-am642-evm.dts
+++ b/arch/arm/dts/k3-am642-evm.dts
@@ -201,6 +201,12 @@
 			AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
 		>;
 	};
+
+	main_usb0_pins_default: main-usb0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
+		>;
+	};
 };
 
 &main_uart0 {
@@ -337,3 +343,15 @@
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
 };
+
+&usbss0 {
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb0_pins_default>;
+};
diff --git a/arch/arm/dts/k3-am642-r5-evm.dts b/arch/arm/dts/k3-am642-r5-evm.dts
index 1fbf6d2c23a5..cc48fd4cb607 100644
--- a/arch/arm/dts/k3-am642-r5-evm.dts
+++ b/arch/arm/dts/k3-am642-r5-evm.dts
@@ -141,6 +141,12 @@
 			AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7)	/* (L18) OSPI0_CSN1.GPIO0_12 */
 		>;
 	};
+
+	main_usb0_pins_default: main-usb0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
+		>;
+	};
 };
 
 &dmsc {
@@ -201,4 +207,16 @@
 	/delete-property/ power-domains;
 };
 
+&usbss0 {
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb0_pins_default>;
+};
+
 #include "k3-am642-evm-u-boot.dtsi"
-- 
2.17.1



More information about the U-Boot mailing list