[BUG] network is broken on Orange Pi PC
Heinrich Schuchardt
xypron.glpk at gmx.de
Thu Jun 3 22:19:00 CEST 2021
On 6/3/21 8:00 PM, Andreas Rehn wrote:
>
>
> Am Do., 3. Juni 2021 um 18:58 Uhr schrieb Andre Przywara
> <andre.przywara at arm.com <mailto:andre.przywara at arm.com>>:
>
> On Thu, 3 Jun 2021 18:09:25 +0200
> Heinrich Schuchardt <xypron.glpk at gmx.de <mailto:xypron.glpk at gmx.de>>
> wrote:
>
> Hi,
>
> > On 6/3/21 1:04 PM, Andre Przywara wrote:
> > > On Thu, 3 Jun 2021 12:20:34 +0200
> > > Heinrich Schuchardt <xypron.glpk at gmx.de
> <mailto:xypron.glpk at gmx.de>> wrote:
> > >
> > > Hi,
> > >
> > >> On 6/3/21 11:04 AM, Andre Przywara wrote:
> > >>> On Thu, 3 Jun 2021 09:46:48 +0200
> > >>> Heinrich Schuchardt <xypron.glpk at gmx.de
> <mailto:xypron.glpk at gmx.de>> wrote:
> > >>>
> > >>> Hi Heinrich,
> > >>>
> > >>>> On 6/2/21 3:08 PM, Ramon Fried wrote:
> > >>>>> On Tue, Jun 1, 2021 at 12:35 AM Heinrich Schuchardt
> <xypron.glpk at gmx.de <mailto:xypron.glpk at gmx.de>> wrote:
> > >>>>>>
> > >>>>>> Dear all,
> > >>>>>>
> > >>>>>> network is broken in U-Boot on orangepi_pc_defconfig:
> > >>>
> > >>> Thanks for the report!
> > >>>
> > >>>>>>
> > >>>>>> U-Boot 2021.07-rc3-00059-gd8729a114e (May 31 2021 -
> 21:26:56 +0000)
> > >>>>>> Allwinner Technology
> > >>>>>> eth0: ethernet at 1c30000
> > >>>>>> => dhcp
> > >>>>>> sun8i_emac_eth_start: Timeout
> > >>>>>>
> > >>>>>> Best regards
> > >>>>>>
> > >>>>>> Heinrich
> > >>>>>>
> > >>>>> Hi Heinrich, I don't have OrangePi. can you bisect and tell
> me when it broke ?
> > >>>>> Thanks.
> > >>>>> Ramon.
> > >>>>>
> > >>>>
> > >>>> Git bisect points to:
> > >>>>
> > >>>> commit 4f0278dac56a658ef1e0967fec0bb95372a875bd
> > >>>> Author: Andre Przywara <andre.przywara at arm.com
> <mailto:andre.przywara at arm.com>>
> > >>>> Date: Mon Jul 6 01:40:45 2020 +0100
> > >>>>
> > >>>> net: sun8i-emac: Lower MDIO frequency
> > >>>>
> > >>>> Reverting the patch solves the problem for the OrangePi PC.
> > >>>>
> > >>>> According to the commit message the change was only needed
> for needed
> > >>>> for external PHYs.
> > >>>
> > >>> The external PHY on the Pine64 (non-plus) was the trigger,
> however
> > >>> both the manual and the Linux driver point to that we
> definitely need a
> > >>> higher divider. From what I can see, AHB2 (the EMAC clock)
> runs at 200
> > >>> MHz (AHB2=AHB1/1=PLL6/3=200 MHz). So just having "/ 16"
> results in 12.5
> > >>> MHz MDIO frequency. Can you check whether any other divider
> values fix
> > >>> this for you as well?
> > >>
> > >> MDIO_CMD_MII_CLK_CSR_DIV_16 = 0 and this is the value that was
> used
> > >> before your patch.
> > >>
> > >> MDIO_CMD_MII_CLK_CSR_DIV_16 = 0 =>
> > >> Waiting for PHY auto negotiation to complete. done
> > >> MDIO_CMD_MII_CLK_CSR_DIV_32 = 1 => sun8i_emac_eth_start: Timeout
> > >> MDIO_CMD_MII_CLK_CSR_DIV_64 = 2 => sun8i_emac_eth_start: Timeout
> > >> MDIO_CMD_MII_CLK_CSR_DIV_128 = 3 => sun8i_emac_eth_start: Timeout
> > >>
> > >> What is wrong about the approach in
> > >>
> > >> [PATCH 1/1] net: sun8i-emac: fix MDIO frequency
> > >> https://lists.denx.de/pipermail/u-boot/2021-June/451305.html
> <https://lists.denx.de/pipermail/u-boot/2021-June/451305.html> ?
> > >
> > > The MDIO spec says that the maximum frequency on the MDIO bus
> should be
> > > 2.5 MHz. On the H3 with 200 MHz AHB and with a divider of 16
> it's 12.5
> >
> > The dts says for the MDIO:
> >
> > int_mii_phy: ethernet-phy at 1 {
> > clocks = <&ccu CLK_BUS_EPHY>;
>
> I think that is the clock to drive the PHY logic, not the MDIO bus.
> It's a gate for AHB1, in this case, which seems to be 200 MHz as well
> (because rate(AHB2)=rate(AHB1)/1).
>
> > "ahb" refers to CLK_BUS_SPI1:
> >
> > spi1: spi at 1c69000 {
> > clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> > clock-names = "ahb", "mod";
> >
> > Why are you mentioning AHB?
>
> AHB stands for "Advanced High-performance Bus", which is a traditional
> term for a (faster, data centric) bus interface in the ARM
> bus world. I am not sure the exact term is actually correct anymore
> with recent bus implementations, but the H3 manual refers to AHB
> everywhere, in particular as the bus name for the EMAC IP (figure
> 4-1 System
> Bus Tree). Apparently the bus clock is used as the clock source for the
> MDIO bus as well - after dividing it.
>
> > > MHz. Apparently the internal H3 PHY can tolerate those high
> > > frequencies, but it's beyond the spec. And certainly it should
> not fail
> > > with lower frequencies. And indeed it works for me on the H2+
> (which I
> > > understand is just a binned version of the H3).
> > >
> > >> The Linux 5.10 driver runs fine no matter what value we choose
> for the
> > >> divider in U-Boot.
> > >
> > > Because it programs the divider correctly:
> > >
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c#n316
> <https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c#n316>
> > > I take it you have no problems with Linux, so the divider being too
> > > high cannot be the root cause of the problem.
> >
> > Function stmmac_clk_csr_set() depends on the rate of the clock named
> > "stmmaceth":
> >
> > ethernet at 1c30000 {
> > clocks = <&ccu CLK_BUS_EMAC>;
> > clock-names = "stmmaceth";
> >
> > How do we get the frequency of this clock?
>
> Have you checked /sys/kernel/debug/clk/clk_summary? You could also
> insert some printk to be sure. Otherwise the definition of bus_emac_clk
> and CLK_BUS_EMAC in drivers/clk/sunxi-ng/ccu-sun8i-h3.c tell you that
> it's a gate for ahb2. All of those point to 200 MHz on my OPi Zero.
>
> Hope that helps!
>
> Cheers,
> Andre
> >
> > Best regards
> >
> > Heinrich
> >
> > >
> > > So I'd rather fix this problem properly and correctly,
> especially as it
> > > seems to be more related to the EMAC soft reset (where your error
> > > message comes from).
> > >
> > >> But I see a message:
> > >>
> > >> dwmac-sun8i 1c30000.ethernet:
> > >> Current syscon value is not the default 148000 (expect 58000)
> > >>
> > >> @default_syscon_value:
> > >> The default value of the EMAC register in syscon
> > >> This value is used for disabling properly EMAC
> > >> and used as a good starting value in case of the
> > >> boot process(uboot) leave some stuff.
> > >
> > > Yeah, I never got the reason for this message. If Linux wants a
> > > certain value, it should program that. Whatever was left by someone
> > > else (be it U-Boot or some other software/OS) should not matter.
> > >
> > > Cheers,
> > > Andre
> > >
> > >>
> > >> Best regards
> > >>
> > >> Heinrich
> > >>
> > >>>
> > >>>> Can't we let the change depend on priv->use_internal_phy?
> > >>>>
> > >>>> diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c
> > >>>> index 5a1b38bf80..d7553fe163 100644
> > >>>> --- a/drivers/net/sun8i_emac.c
> > >>>> +++ b/drivers/net/sun8i_emac.c
> > >>>> @@ -211,7 +211,9 @@ static int sun8i_mdio_read(struct
> mii_dev *bus, int
> > >>>> addr, int devad, int reg)
> > >>>> * The EMAC clock is either 200 or 300 MHz, so we
> need a divider
> > >>>> * of 128 to get the MDIO frequency below the
> required 2.5 MHz.
> > >>>> */
> > >>>> - mii_cmd |= MDIO_CMD_MII_CLK_CSR_DIV_128 <<
> > >>>> MDIO_CMD_MII_CLK_CSR_SHIFT;
> > >>>> + if (!priv->use_internal_phy)
> > >>>> + mii_cmd |= MDIO_CMD_MII_CLK_CSR_DIV_128 <<
> > >>>> + MDIO_CMD_MII_CLK_CSR_SHIFT;
> > >>>>
> > >>>> mii_cmd |= MDIO_CMD_MII_BUSY;
> > >>>>
> > >>>> @@ -242,7 +244,9 @@ static int sun8i_mdio_write(struct
> mii_dev *bus, int
> > >>>> addr, int devad, int reg,
> > >>>> * The EMAC clock is either 200 or 300 MHz, so we
> need a divider
> > >>>> * of 128 to get the MDIO frequency below the
> required 2.5 MHz.
> > >>>> */
> > >>>> - mii_cmd |= MDIO_CMD_MII_CLK_CSR_DIV_128 <<
> > >>>> MDIO_CMD_MII_CLK_CSR_SHIFT;
> > >>>> + if (!priv->use_internal_phy)
> > >>>> + mii_cmd |= MDIO_CMD_MII_CLK_CSR_DIV_128 <<
> > >>>> + MDIO_CMD_MII_CLK_CSR_SHIFT;
> > >>>>
> > >>>> mii_cmd |= MDIO_CMD_MII_WRITE;
> > >>>> mii_cmd |= MDIO_CMD_MII_BUSY;
>
>
> I tried this with my v3s which has only an internal phy.
> u-boot wasn't able to establish a connection with any speed and duplex
> mode combination.
> All i get is `ethernet at 1c30000 Waiting for PHY auto negotiation to
> complete......... TIMEOUT !`
>
> Do you work with the internal or external phy @Heinrich?
> Did you try the default u-boot with a different speed and duplex mode
> combination and have the same behavior?
> Greetings andreas
I simply use orangepi_pc_defconfig. It worked out of the box in the
previous release. Communication speed and duplex mode should be
auto-negotiated.
Best regards
Heinrich
>
> > >>>>
> > >>>> Best regards
> > >>>>
> > >>>> Heinrich
> > >>>>
> > >>>> I would assume the problem hits all H3 boards.
> > >>>
> > >>> And that's the confusing part: it does not. I tested this on my
> > >>> OrangePi Zero (H2+ with internal PHY), both back then with
> the original
> > >>> MDIO frequency patch and also now after your report. It
> always worked
> > >>> reliably for me.
> > >>> Also: I am still puzzled how one influences the other: The
> error you
> > >>> get is from the *MAC* soft reset: I would think this is an
> independent
> > >>> operation from any communication attempts with the PHY.
> > >>>
> > >>> There is this thread here about the same symptom on a V3s:
> > >>> https://lists.denx.de/pipermail/u-boot/2021-May/450315.html
> <https://lists.denx.de/pipermail/u-boot/2021-May/450315.html>
> > >>> v2 of this original patch (in the same thread) proposes some
> other
> > >>> solution, which I am also not very happy with. But just to
> get some more
> > >>> data points: can you check whether skipping the soft reset
> fixes this
> > >>> for you? I will have a closer look tonight to check the order
> of soft
> > >>> reset and PHY communication. Maybe we should only do the soft
> reset
> > >>> *once* when the MAC probes, and not on every .start call?
> > >>>
> > >>> Thanks,
> > >>> Andre
> > >>>
> > >>
> > >
> >
>
>
>
> --
> Mit freundlichen Grüßen / kind regards
> Andreas Rehn | Master of Engineering (M.Eng)
More information about the U-Boot
mailing list