[PATCH u-boot-marvell 2/2] arm: mvebu: turris_omnia: support invoking rescue boot from console

[Stefan Roese]

On 28.05.21 10:00, Marek Behún wrote:
> Make it possible to invoke rescue boot from U-Boot console, without
> having to press the factory reset button. This is needed when accessing
> the device remotely, for example.
> 
> Achieve this by putting rescue command into `bootcmd_rescue` default
> environment variable and setting some distroboot environment variables
> to their default values when the factory button is pressed.
> 
> Rescue boot from console can be invoked by running
>    run bootcmd_rescue
> 
> Signed-off-by: Marek Behún <marek.behun at nic.cz>

Applied to u-boot-marvell/master

Thanks,
Stefan

> ---
>   board/CZ.NIC/turris_omnia/turris_omnia.c | 53 +++++++++++++-----------
>   include/configs/turris_omnia.h           | 23 ++++++++++
>   2 files changed, 52 insertions(+), 24 deletions(-)
> 
> diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
> index d3de8004eb..ade923f599 100644
> --- a/board/CZ.NIC/turris_omnia/turris_omnia.c
> +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
> @@ -337,29 +337,6 @@ static int set_regdomain(void)
>   	return env_set("regdomain", rd);
>   }
>   
> -/*
> - * default factory reset bootcommand on Omnia first sets all the front LEDs
> - * to green and then tries to load the rescue image from SPI flash memory and
> - * boot it
> - */
> -#define OMNIA_FACTORY_RESET_BOOTCMD \
> -	"i2c dev 2; " \
> -	"i2c mw 0x2a.1 0x3 0x1c 1; " \
> -	"i2c mw 0x2a.1 0x4 0x1c 1; " \
> -	"mw.l 0x01000000 0x00ff000c; " \
> -	"i2c write 0x01000000 0x2a.1 0x5 4 -s; " \
> -	"setenv bootargs \"earlyprintk console=ttyS0,115200" \
> -		" omniarescue=$omnia_reset rescue_mode=$omnia_reset\"; " \
> -	"sf probe; " \
> -	"sf read 0x1000000 0x100000 0x700000; " \
> -	"lzmadec 0x1000000 0x1700000; " \
> -	"if gpio input gpio at 71_4; then " \
> -		"bootm 0x1700000#sfp; " \
> -	"else " \
> -		"bootm 0x1700000; " \
> -	"fi; " \
> -	"bootz 0x1000000"
> -
>   static void handle_reset_button(void)
>   {
>   	int ret;
> @@ -375,8 +352,36 @@ static void handle_reset_button(void)
>   	env_set_ulong("omnia_reset", reset_status);
>   
>   	if (reset_status) {
> +		const char * const vars[3] = {
> +			"bootcmd",
> +			"bootcmd_rescue",
> +			"distro_bootcmd",
> +		};
> +
> +		/*
> +		 * Set the above envs to their default values, in case the user
> +		 * managed to break them.
> +		 */
> +		env_set_default_vars(3, (char * const *)vars, 0);
> +
> +		/* Ensure bootcmd_rescue is used by distroboot */
> +		env_set("boot_targets", "rescue");
> +
>   		printf("RESET button was pressed, overwriting bootcmd!\n");
> -		env_set("bootcmd", OMNIA_FACTORY_RESET_BOOTCMD);
> +	} else {
> +		/*
> +		 * In case the user somehow managed to save environment with
> +		 * boot_targets=rescue, reset boot_targets to default value.
> +		 * This could happen in subsequent commands if bootcmd_rescue
> +		 * failed.
> +		 */
> +		if (!strcmp(env_get("boot_targets"), "rescue")) {
> +			const char * const vars[1] = {
> +				"boot_targets",
> +			};
> +
> +			env_set_default_vars(1, (char * const *)vars, 0);
> +		}
>   	}
>   }
>   #endif
> diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h
> index 0b55c14d8b..7da18f97db 100644
> --- a/include/configs/turris_omnia.h
> +++ b/include/configs/turris_omnia.h
> @@ -108,12 +108,35 @@
>   
>   #include <config_distro_bootcmd.h>
>   
> +/*
> + * The factory reset bootcommand on Omnia first sets all the front LEDs to green
> + * and then tries to load the rescue image from SPI flash memory and boot it
> + */
> +#define TURRIS_OMNIA_BOOTCMD_RESCUE \
> +	"i2c dev 2; " \
> +	"i2c mw 0x2a.1 0x3 0x1c 1; " \
> +	"i2c mw 0x2a.1 0x4 0x1c 1; " \
> +	"mw.l 0x01000000 0x00ff000c; " \
> +	"i2c write 0x01000000 0x2a.1 0x5 4 -s; " \
> +	"setenv bootargs \"earlyprintk console=ttyS0,115200" \
> +		" omniarescue=$omnia_reset rescue_mode=$omnia_reset\"; " \
> +	"sf probe; " \
> +	"sf read 0x1000000 0x100000 0x700000; " \
> +	"lzmadec 0x1000000 0x1700000; " \
> +	"if gpio input gpio at 71_4; then " \
> +		"bootm 0x1700000#sfp; " \
> +	"else " \
> +		"bootm 0x1700000; " \
> +	"fi; " \
> +	"bootz 0x1000000"
> +
>   #define CONFIG_EXTRA_ENV_SETTINGS \
>   	RELOCATION_LIMITS_ENV_SETTINGS \
>   	LOAD_ADDRESS_ENV_SETTINGS \
>   	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
>   	"console=ttyS0,115200\0" \
>   	"ethact=ethernet at 34000\0" \
> +	"bootcmd_rescue=" TURRIS_OMNIA_BOOTCMD_RESCUE "\0" \
>   	BOOTENV
>   
>   #endif /* CONFIG_SPL_BUILD */
> 


Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de