[PATCH v2 1/8] lpc32xx: Kconfig: switch to CONFIG_CONS_INDEX
Trevor Woerner
twoerner at gmail.com
Fri Jun 11 04:37:02 CEST 2021
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner at gmail.com>
---
(no changes since v1)
arch/arm/include/asm/arch-lpc32xx/config.h | 4 ++--
arch/arm/mach-lpc32xx/devices.c | 3 +--
board/timll/devkit3250/devkit3250.c | 2 +-
board/timll/devkit3250/devkit3250_spl.c | 2 +-
board/work-microwave/work_92105/work_92105.c | 2 +-
board/work-microwave/work_92105/work_92105_spl.c | 2 +-
configs/devkit3250_defconfig | 2 ++
configs/work_92105_defconfig | 2 ++
include/configs/devkit3250.h | 5 -----
include/configs/work_92105.h | 5 -----
scripts/config_whitelist.txt | 1 -
11 files changed, 11 insertions(+), 19 deletions(-)
diff --git a/arch/arm/include/asm/arch-lpc32xx/config.h b/arch/arm/include/asm/arch-lpc32xx/config.h
index 0836091af2..45e46f9946 100644
--- a/arch/arm/include/asm/arch-lpc32xx/config.h
+++ b/arch/arm/include/asm/arch-lpc32xx/config.h
@@ -12,8 +12,8 @@
/* Basic CPU architecture */
/* UART configuration */
-#if (CONFIG_SYS_LPC32XX_UART == 1) || (CONFIG_SYS_LPC32XX_UART == 2) || \
- (CONFIG_SYS_LPC32XX_UART == 7)
+#if (CONFIG_CONS_INDEX == 1) || (CONFIG_CONS_INDEX == 2) || \
+ (CONFIG_CONS_INDEX == 7)
#if !defined(CONFIG_LPC32XX_HSUART)
#define CONFIG_LPC32XX_HSUART
#endif
diff --git a/arch/arm/mach-lpc32xx/devices.c b/arch/arm/mach-lpc32xx/devices.c
index e1e2e0d094..0a4fef295a 100644
--- a/arch/arm/mach-lpc32xx/devices.c
+++ b/arch/arm/mach-lpc32xx/devices.c
@@ -23,8 +23,7 @@ void lpc32xx_uart_init(unsigned int uart_id)
return;
/* Disable loopback mode, if it is set by S1L bootloader */
- clrbits_le32(&ctrl->loop,
- UART_LOOPBACK(CONFIG_SYS_LPC32XX_UART));
+ clrbits_le32(&ctrl->loop, UART_LOOPBACK(uart_id));
if (uart_id < 3 || uart_id > 6)
return;
diff --git a/board/timll/devkit3250/devkit3250.c b/board/timll/devkit3250/devkit3250.c
index 3c744b943f..9d4ffb0f97 100644
--- a/board/timll/devkit3250/devkit3250.c
+++ b/board/timll/devkit3250/devkit3250.c
@@ -38,7 +38,7 @@ void reset_periph(void)
int board_early_init_f(void)
{
- lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ lpc32xx_uart_init(CONFIG_CONS_INDEX);
lpc32xx_i2c_init(1);
lpc32xx_i2c_init(2);
lpc32xx_ssp_init();
diff --git a/board/timll/devkit3250/devkit3250_spl.c b/board/timll/devkit3250/devkit3250_spl.c
index 47af78ae0b..12e8ae9c39 100644
--- a/board/timll/devkit3250/devkit3250_spl.c
+++ b/board/timll/devkit3250/devkit3250_spl.c
@@ -49,7 +49,7 @@ void spl_board_init(void)
/* First of all silence buzzer controlled by GPO_20 */
writel((1 << 20), &gpio->p3_outp_clr);
- lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ lpc32xx_uart_init(CONFIG_CONS_INDEX);
preloader_console_init();
ddr_init(&dram_64mb);
diff --git a/board/work-microwave/work_92105/work_92105.c b/board/work-microwave/work_92105/work_92105.c
index bdcecff730..5d12f84cfe 100644
--- a/board/work-microwave/work_92105/work_92105.c
+++ b/board/work-microwave/work_92105/work_92105.c
@@ -37,7 +37,7 @@ void reset_periph(void)
int board_early_init_f(void)
{
/* initialize serial port for console */
- lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ lpc32xx_uart_init(CONFIG_CONS_INDEX);
/* enable I2C, SSP, MAC, NAND */
lpc32xx_i2c_init(1); /* only I2C1 has devices, I2C2 has none */
lpc32xx_ssp_init();
diff --git a/board/work-microwave/work_92105/work_92105_spl.c b/board/work-microwave/work_92105/work_92105_spl.c
index a31553a2d2..d9401145f2 100644
--- a/board/work-microwave/work_92105/work_92105_spl.c
+++ b/board/work-microwave/work_92105/work_92105_spl.c
@@ -58,7 +58,7 @@ const struct emc_dram_settings dram_128mb = {
void spl_board_init(void)
{
/* initialize serial port for console */
- lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+ lpc32xx_uart_init(CONFIG_CONS_INDEX);
/* initialize console */
preloader_console_init();
/* init DDR and NAND to chainload U-Boot */
diff --git a/configs/devkit3250_defconfig b/configs/devkit3250_defconfig
index 93c048cee8..9ae70f7d46 100644
--- a/configs/devkit3250_defconfig
+++ b/configs/devkit3250_defconfig
@@ -51,6 +51,8 @@ CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=31
CONFIG_PHY_SMSC=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_CONS_INDEX=5
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_USB=y
diff --git a/configs/work_92105_defconfig b/configs/work_92105_defconfig
index c3f666dcfe..e9605adedd 100644
--- a/configs/work_92105_defconfig
+++ b/configs/work_92105_defconfig
@@ -48,5 +48,7 @@ CONFIG_MTD_RAW_NAND=y
CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_SMSC=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_CONS_INDEX=5
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index 5d2b77b4a3..921a38c01e 100644
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -30,11 +30,6 @@
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \
- GENERATED_GBL_DATA_SIZE)
-/*
- * Serial Driver
- */
-#define CONFIG_SYS_LPC32XX_UART 5 /* UART5 */
-
/*
* DMA
*/
diff --git a/include/configs/work_92105.h b/include/configs/work_92105.h
index 7874b77f3f..076a1b065e 100644
--- a/include/configs/work_92105.h
+++ b/include/configs/work_92105.h
@@ -35,11 +35,6 @@
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_512K \
- GENERATED_GBL_DATA_SIZE)
-/*
- * Serial Driver
- */
-#define CONFIG_SYS_LPC32XX_UART 5 /* UART5 - NS16550 */
-
/*
* Ethernet Driver
*/
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 0f5ac8ff52..13281bf6b1 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -2735,7 +2735,6 @@ CONFIG_SYS_LOW
CONFIG_SYS_LOWMEM_BASE
CONFIG_SYS_LOW_RES_TIMER
CONFIG_SYS_LPAE_SDRAM_BASE
-CONFIG_SYS_LPC32XX_UART
CONFIG_SYS_LS1_DDR_BLOCK1_SIZE
CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH
CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS
--
2.30.0.rc0
More information about the U-Boot
mailing list