[PATCHv6 00/26] HSM rearch series for TI K3 devices

[Tero Kristo]

On 11/06/2021 14:08, Lokesh Vutla wrote:
> Hi Tero,
> 
> On 11/06/21 2:15 pm, Tero Kristo wrote:
>> Hello,
>>
>> One more post, this time with the #ifdef hackery converted to use the
>> IS_ENABLED / CONFIG_IS_ENABLED macros, and also removed the "common.h"
>> include from k3-clk.h header. This version also contains fixes to any
>> build issues reported by Lokesh, and these are squashed in to relevant
>> patches.
> 
> Can you see if the below warnings can be fixed?
> 
> hsm/0018-arm-mach-k3-add-support-for-detecting-firmware-image.patch
> -------------------------------------------------------------------
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #26: FILE: arch/arm/mach-k3/common.c:31:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)

This is static data, can't be fixed. Unless we want to compile it in always?

> 
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #35: FILE: arch/arm/mach-k3/common.c:40:
> +#if CONFIG_IS_ENABLED(FIT_IMAGE_POST_PROCESS)

Same, static data.

> 
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #55: FILE: arch/arm/mach-k3/common.c:131:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)

This is actually just an old macro I changed from #ifdef to IS_ENABLED. 
Fixing the whole file from the existing #ifdef:s should be outside the 
scope of this series.

> 
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #124: FILE: arch/arm/mach-k3/common.c:264:
> +#if CONFIG_IS_ENABLED(FIT_IMAGE_POST_PROCESS)

This code addresses the static data defined before, changing this will 
break compilation; unless we compile the data always in.

> 
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #128: FILE: arch/arm/mach-k3/common.c:268:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)

Same as above.

> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #150: FILE: arch/arm/mach-k3/common.c:290:
> +#if IS_ENABLED(CONFIG_TI_SECURE_DEVICE)

This can't be changed, the code it addresses is only linked in with the 
config, causing a linker time failure if this is fixed.

Imho, I am not too convinced about the checkpatch tool complaining about 
these issues. :)

-Tero

> 
> total: 0 errors, 6 warnings, 0 checks, 144 lines checked
> 
> NOTE: For some of the reported defects, checkpatch may be able to
>        mechanically convert to the typical style using --fix or --fix-inplace.
> 
> hsm/0018-arm-mach-k3-add-support-for-detecting-firmware-image.patch has style
> problems, please review.
> -------------------------------------------------------------------
> hsm/0019-arm-mach-k3-do-board-config-for-PM-only-if-supported.patch
> -------------------------------------------------------------------
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #24: FILE: arch/arm/mach-k3/sysfw-loader.c:162:
> +#if !CONFIG_IS_ENABLED(K3_DM_FW)
> 
> total: 0 errors, 1 warnings, 0 checks, 13 lines checked
> 
> NOTE: For some of the reported defects, checkpatch may be able to
>        mechanically convert to the typical style using --fix or --fix-inplace.
> 
> 
> Thanks and regards,
> Lokesh
>