[PATCHv2] zynqmp: spl: support DRAM ECC initialization
Jorge Ramirez-Ortiz
jorge at foundries.io
Sun Jun 13 20:55:53 CEST 2021
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge at foundries.io>
---
v2: extend commit message
_BASE suffix for DRAM_BANK address
DRAM_BANK2_BASE to 0x8.00.00.00.00
remove unnecessary includes from ecc_spl_init.c
add ADMA_CH0_BASEADDR to hardware.h
remove cache management
timeout on loops
retry once on DMA status error
move DMA restore to reset values to its own function(*)
removed extern clause from splc and added header file instead
fixed duplicated call to board_early_init_r()
(*) IP reset: there is no register to toggle (checked docs and linux kernel)
opted for leaving the restore function as per FSBL
arch/arm/mach-zynqmp/Kconfig | 35 ++++
arch/arm/mach-zynqmp/Makefile | 1 +
arch/arm/mach-zynqmp/ecc_spl_init.c | 163 ++++++++++++++++++
.../mach-zynqmp/include/mach/ecc_spl_init.h | 13 ++
arch/arm/mach-zynqmp/include/mach/hardware.h | 2 +
arch/arm/mach-zynqmp/spl.c | 4 +
6 files changed, 218 insertions(+)
create mode 100644 arch/arm/mach-zynqmp/ecc_spl_init.c
create mode 100644 arch/arm/mach-zynqmp/include/mach/ecc_spl_init.h
diff --git a/arch/arm/mach-zynqmp/Kconfig b/arch/arm/mach-zynqmp/Kconfig
index f1301f6661..39144d654e 100644
--- a/arch/arm/mach-zynqmp/Kconfig
+++ b/arch/arm/mach-zynqmp/Kconfig
@@ -92,6 +92,41 @@ config ZYNQMP_NO_DDR
This option configures MMU with no DDR to avoid speculative
access to DDR memory where DDR is not present.
+config SPL_ZYNQMP_DRAM_ECC_INIT
+ bool "Initialize DRAM ECC"
+ depends on SPL
+ help
+ This option initializes all memory to 0xdeadbeef. Must be set if your
+ memory is of ECC type.
+
+config SPL_ZYNQMP_DRAM_BANK1_BASE
+ depends on SPL_ZYNQMP_DRAM_ECC_INIT
+ hex "DRAM Bank1 address"
+ default 0x00000000
+ help
+ Start address of DRAM ECC bank1
+
+config SPL_ZYNQMP_DRAM_BANK1_LEN
+ depends on SPL_ZYNQMP_DRAM_ECC_INIT
+ hex "DRAM Bank1 size"
+ default 0x80000000
+ help
+ Size in bytes of the DRAM ECC bank1
+
+config SPL_ZYNQMP_DRAM_BANK2_BASE
+ depends on SPL_ZYNQMP_DRAM_ECC_INIT
+ hex "DRAM Bank2 address"
+ default 0x800000000
+ help
+ Start address of DRAM ECC bank2
+
+config SPL_ZYNQMP_DRAM_BANK2_LEN
+ depends on SPL_ZYNQMP_DRAM_ECC_INIT
+ hex "DRAM Bank2 size"
+ default 0x0
+ help
+ Size in bytes of the DRAM ECC bank2. A null size takes no action.
+
config SYS_MALLOC_F_LEN
default 0x600
diff --git a/arch/arm/mach-zynqmp/Makefile b/arch/arm/mach-zynqmp/Makefile
index 8a3b074724..eb6c5112b3 100644
--- a/arch/arm/mach-zynqmp/Makefile
+++ b/arch/arm/mach-zynqmp/Makefile
@@ -7,4 +7,5 @@ obj-y += clk.o
obj-y += cpu.o
obj-$(CONFIG_MP) += mp.o
obj-$(CONFIG_SPL_BUILD) += spl.o handoff.o
+obj-$(CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT) += ecc_spl_init.o
obj-$(CONFIG_ZYNQMP_PSU_INIT_ENABLED) += psu_spl_init.o
diff --git a/arch/arm/mach-zynqmp/ecc_spl_init.c b/arch/arm/mach-zynqmp/ecc_spl_init.c
new file mode 100644
index 0000000000..f547d8e3a5
--- /dev/null
+++ b/arch/arm/mach-zynqmp/ecc_spl_init.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright(c) 2015 - 2020 Xilinx, Inc.
+ *
+ * Jorge Ramirez-Ortiz <jorge at foundries.io>
+ */
+
+#include <common.h>
+#include <cpu_func.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/ecc_spl_init.h>
+#include <asm/io.h>
+#include <linux/delay.h>
+
+#define ZDMA_TRANSFER_MAX_LEN (0x3FFFFFFFU - 7U)
+#define ZDMA_CH_STATUS ((ADMA_CH0_BASEADDR) + 0x0000011CU)
+#define ZDMA_CH_STATUS_STATE_MASK 0x00000003U
+#define ZDMA_CH_STATUS_STATE_DONE 0x00000000U
+#define ZDMA_CH_STATUS_STATE_ERR 0x00000003U
+#define ZDMA_CH_CTRL0 ((ADMA_CH0_BASEADDR) + 0x00000110U)
+#define ZDMA_CH_CTRL0_POINT_TYPE_MASK (u32)0x00000040U
+#define ZDMA_CH_CTRL0_POINT_TYPE_NORMAL (u32)0x00000000U
+#define ZDMA_CH_CTRL0_MODE_MASK (u32)0x00000030U
+#define ZDMA_CH_CTRL0_MODE_WR_ONLY (u32)0x00000010U
+#define ZDMA_CH_CTRL0_TOTAL_BYTE_COUNT ((ADMA_CH0_BASEADDR) + 0x00000188U)
+#define ZDMA_CH_WR_ONLY_WORD0 ((ADMA_CH0_BASEADDR) + 0x00000148U)
+#define ZDMA_CH_WR_ONLY_WORD1 ((ADMA_CH0_BASEADDR) + 0x0000014CU)
+#define ZDMA_CH_WR_ONLY_WORD2 ((ADMA_CH0_BASEADDR) + 0x00000150U)
+#define ZDMA_CH_WR_ONLY_WORD3 ((ADMA_CH0_BASEADDR) + 0x00000154U)
+#define ZDMA_CH_DST_DSCR_WORD0 ((ADMA_CH0_BASEADDR) + 0x00000138U)
+#define ZDMA_CH_DST_DSCR_WORD0_LSB_MASK 0xFFFFFFFFU
+#define ZDMA_CH_DST_DSCR_WORD1 ((ADMA_CH0_BASEADDR) + 0x0000013CU)
+#define ZDMA_CH_DST_DSCR_WORD1_MSB_MASK 0x0001FFFFU
+#define ZDMA_CH_SRC_DSCR_WORD2 ((ADMA_CH0_BASEADDR) + 0x00000130U)
+#define ZDMA_CH_DST_DSCR_WORD2 ((ADMA_CH0_BASEADDR) + 0x00000140U)
+#define ZDMA_CH_CTRL2 ((ADMA_CH0_BASEADDR) + 0x00000200U)
+#define ZDMA_CH_CTRL2_EN_MASK 0x00000001U
+#define ZDMA_CH_ISR ((ADMA_CH0_BASEADDR) + 0x00000100U)
+#define ZDMA_CH_ISR_DMA_DONE_MASK 0x00000400U
+#define ECC_INIT_VAL_WORD 0xDEADBEEFU
+
+#define ZDMA_IDLE_TIMEOUT_USEC 1000000
+#define ZDMA_DONE_TIMEOUT_USEC 5000000
+
+static void ecc_zdma_restore(void)
+{
+ /* Restore reset values for the DMA registers used */
+ writel(ZDMA_CH_CTRL0, 0x00000080U);
+ writel(ZDMA_CH_WR_ONLY_WORD0, 0x00000000U);
+ writel(ZDMA_CH_WR_ONLY_WORD1, 0x00000000U);
+ writel(ZDMA_CH_WR_ONLY_WORD2, 0x00000000U);
+ writel(ZDMA_CH_WR_ONLY_WORD3, 0x00000000U);
+ writel(ZDMA_CH_DST_DSCR_WORD0, 0x00000000U);
+ writel(ZDMA_CH_DST_DSCR_WORD1, 0x00000000U);
+ writel(ZDMA_CH_SRC_DSCR_WORD2, 0x00000000U);
+ writel(ZDMA_CH_DST_DSCR_WORD2, 0x00000000U);
+ writel(ZDMA_CH_CTRL0_TOTAL_BYTE_COUNT, 0x00000000U);
+}
+
+static void ecc_dram_bank_init(u64 addr, u64 len)
+{
+ bool retry = true;
+ u32 timeout;
+ u64 bytes;
+ u32 size;
+ u64 src;
+ u32 reg;
+
+ if (!len)
+ return;
+retry:
+ bytes = len;
+ src = addr;
+ ecc_zdma_restore();
+ while (bytes > 0) {
+ size = bytes > ZDMA_TRANSFER_MAX_LEN ?
+ ZDMA_TRANSFER_MAX_LEN : (u32)bytes;
+
+ /* Wait until the DMA is in idle state */
+ timeout = ZDMA_IDLE_TIMEOUT_USEC;
+ do {
+ udelay(1);
+ reg = readl(ZDMA_CH_STATUS);
+ reg &= ZDMA_CH_STATUS_STATE_MASK;
+ if (!timeout--) {
+ puts("error, ECC DMA failed to idle\n");
+ goto done;
+ }
+
+ } while ((reg != ZDMA_CH_STATUS_STATE_DONE) &&
+ (reg != ZDMA_CH_STATUS_STATE_ERR));
+
+ /* Enable Simple (Write Only) Mode */
+ reg = readl(ZDMA_CH_CTRL0);
+ reg &= (ZDMA_CH_CTRL0_POINT_TYPE_MASK |
+ ZDMA_CH_CTRL0_MODE_MASK);
+ reg |= (ZDMA_CH_CTRL0_POINT_TYPE_NORMAL |
+ ZDMA_CH_CTRL0_MODE_WR_ONLY);
+ writel(reg, ZDMA_CH_CTRL0);
+
+ /* Fill in the data to be written */
+ writel(ECC_INIT_VAL_WORD, ZDMA_CH_WR_ONLY_WORD0);
+ writel(ECC_INIT_VAL_WORD, ZDMA_CH_WR_ONLY_WORD1);
+ writel(ECC_INIT_VAL_WORD, ZDMA_CH_WR_ONLY_WORD2);
+ writel(ECC_INIT_VAL_WORD, ZDMA_CH_WR_ONLY_WORD3);
+
+ /* Write Destination Address */
+ writel((u32)(src & ZDMA_CH_DST_DSCR_WORD0_LSB_MASK),
+ ZDMA_CH_DST_DSCR_WORD0);
+ writel((u32)((src >> 32) & ZDMA_CH_DST_DSCR_WORD1_MSB_MASK),
+ ZDMA_CH_DST_DSCR_WORD1);
+
+ /* Size to be Transferred. Recommended to set both src and dest sizes */
+ writel(size, ZDMA_CH_SRC_DSCR_WORD2);
+ writel(size, ZDMA_CH_DST_DSCR_WORD2);
+
+ /* DMA Enable */
+ reg = readl(ZDMA_CH_CTRL2);
+ reg |= ZDMA_CH_CTRL2_EN_MASK;
+ writel(reg, ZDMA_CH_CTRL2);
+
+ /* Check the status of the transfer by polling on DMA Done */
+ timeout = ZDMA_DONE_TIMEOUT_USEC;
+ do {
+ udelay(1);
+ reg = readl(ZDMA_CH_ISR);
+ reg &= ZDMA_CH_ISR_DMA_DONE_MASK;
+ if (!timeout--) {
+ puts("error, ECC DMA timeout\n");
+ goto done;
+ }
+ } while (reg != ZDMA_CH_ISR_DMA_DONE_MASK);
+
+ /* Clear DMA status */
+ reg = readl(ZDMA_CH_ISR);
+ reg |= ZDMA_CH_ISR_DMA_DONE_MASK;
+ writel(ZDMA_CH_ISR_DMA_DONE_MASK, ZDMA_CH_ISR);
+
+ /* Read the channel status for errors */
+ reg = readl(ZDMA_CH_STATUS);
+ if (reg == ZDMA_CH_STATUS_STATE_ERR) {
+ if (retry) {
+ retry = false;
+ goto retry;
+ }
+ puts("error, ECC DMA error\n");
+ break;
+ }
+
+ bytes -= size;
+ src += size;
+ }
+done:
+ ecc_zdma_restore();
+}
+
+void zynqmp_ecc_init(void)
+{
+ ecc_dram_bank_init(CONFIG_SPL_ZYNQMP_DRAM_BANK1_BASE,
+ CONFIG_SPL_ZYNQMP_DRAM_BANK1_LEN);
+ ecc_dram_bank_init(CONFIG_SPL_ZYNQMP_DRAM_BANK2_BASE,
+ CONFIG_SPL_ZYNQMP_DRAM_BANK2_LEN);
+}
diff --git a/arch/arm/mach-zynqmp/include/mach/ecc_spl_init.h b/arch/arm/mach-zynqmp/include/mach/ecc_spl_init.h
new file mode 100644
index 0000000000..b4b6fcf53b
--- /dev/null
+++ b/arch/arm/mach-zynqmp/include/mach/ecc_spl_init.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright(c) 2015 - 2020 Xilinx, Inc.
+ *
+ * Jorge Ramirez-Ortiz <jorge at foundries.io>
+ */
+
+#ifndef __ARCH_ZYNQMP_ECC_INIT_H
+#define __ARCH_ZYNQMP_ECC_INIT_H
+
+void zynqmp_ecc_init(void);
+
+#endif
diff --git a/arch/arm/mach-zynqmp/include/mach/hardware.h b/arch/arm/mach-zynqmp/include/mach/hardware.h
index 3d3c48e247..fa612887a4 100644
--- a/arch/arm/mach-zynqmp/include/mach/hardware.h
+++ b/arch/arm/mach-zynqmp/include/mach/hardware.h
@@ -19,6 +19,8 @@
#define ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_EN_SHIFT 0
#define ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_VAL_SHIFT 8
+#define ADMA_CH0_BASEADDR 0xFFA80000
+
#define PS_MODE0 BIT(0)
#define PS_MODE1 BIT(1)
#define PS_MODE2 BIT(2)
diff --git a/arch/arm/mach-zynqmp/spl.c b/arch/arm/mach-zynqmp/spl.c
index 88386b23e5..8fcae2c6a6 100644
--- a/arch/arm/mach-zynqmp/spl.c
+++ b/arch/arm/mach-zynqmp/spl.c
@@ -15,6 +15,7 @@
#include <asm/io.h>
#include <asm/spl.h>
#include <asm/arch/hardware.h>
+#include <asm/arch/ecc_spl_init.h>
#include <asm/arch/psu_init_gpl.h>
#include <asm/arch/sys_proto.h>
@@ -22,6 +23,9 @@ void board_init_f(ulong dummy)
{
board_early_init_f();
board_early_init_r();
+#ifdef CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT
+ zynqmp_ecc_init();
+#endif
}
static void ps_mode_reset(ulong mode)
--
2.31.1
More information about the U-Boot
mailing list