[PATCH 04/11] mmc: fsl_esdhc_imx: clean up bus width configuration code

Sean Anderson sean.anderson at seco.com
Fri Nov 5 18:39:37 CET 2021


[ fsl_esdhc commit 07bae1de382723b94244096953b05225572728cd ]

This patch is to clean up bus width setting code.

- For DM_MMC, remove getting "bus-width" from device tree.
  This has been done in mmc_of_parse().

- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
  to fsl_esdhc_initialize() which is non-DM_MMC specific.
  And fix up bus width configuration to support only 1-bit, 4-bit,
  or 8-bit. Keep using 8-bit if it's not set because many platforms
  use driver without providing max bus width.

- Remove bus_width member from fsl_esdhc_priv structure.

Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
Signed-off-by: Sean Anderson <sean.anderson at seco.com>
---

 drivers/mmc/fsl_esdhc_imx.c | 80 +++++++++++--------------------------
 1 file changed, 23 insertions(+), 57 deletions(-)

diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c
index b91dda27f9..d3daf4db59 100644
--- a/drivers/mmc/fsl_esdhc_imx.c
+++ b/drivers/mmc/fsl_esdhc_imx.c
@@ -126,7 +126,6 @@ struct esdhc_soc_data {
  *
  * @esdhc_regs: registers of the sdhc controller
  * @sdhc_clk: Current clk of the sdhc controller
- * @bus_width: bus width, 1bit, 4bit or 8bit
  * @cfg: mmc config
  * @mmc: mmc
  * Following is used when Driver Model is enabled for MMC
@@ -151,7 +150,6 @@ struct fsl_esdhc_priv {
 	struct clk per_clk;
 	unsigned int clock;
 	unsigned int mode;
-	unsigned int bus_width;
 #if !CONFIG_IS_ENABLED(DM_MMC)
 	struct mmc *mmc;
 #endif
@@ -1232,31 +1230,13 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 #if !CONFIG_IS_ENABLED(DM_MMC)
 	cfg->ops = &esdhc_ops;
 #endif
-	if (priv->bus_width == 8)
-		cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
-	else if (priv->bus_width == 4)
-		cfg->host_caps = MMC_MODE_4BIT;
-
-	cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT;
 #ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
 	cfg->host_caps |= MMC_MODE_DDR_52MHz;
 #endif
 
-	if (priv->bus_width > 0) {
-		if (priv->bus_width < 8)
-			cfg->host_caps &= ~MMC_MODE_8BIT;
-		if (priv->bus_width < 4)
-			cfg->host_caps &= ~MMC_MODE_4BIT;
-	}
-
 	if (caps & HOSTCAPBLT_HSS)
 		cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
 
-#ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK
-	if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK)
-		cfg->host_caps &= ~MMC_MODE_8BIT;
-#endif
-
 	cfg->host_caps |= priv->caps;
 
 	cfg->f_min = 400000;
@@ -1294,25 +1274,11 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 }
 
 #if !CONFIG_IS_ENABLED(DM_MMC)
-static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
-				 struct fsl_esdhc_priv *priv)
-{
-	if (!cfg || !priv)
-		return -EINVAL;
-
-	priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
-	priv->bus_width = cfg->max_bus_width;
-	priv->sdhc_clk = cfg->sdhc_clk;
-	priv->wp_enable  = cfg->wp_enable;
-	priv->vs18_enable  = cfg->vs18_enable;
-
-	return 0;
-};
-
 int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg)
 {
 	struct fsl_esdhc_plat *plat;
 	struct fsl_esdhc_priv *priv;
+	struct mmc_config *mmc_cfg;
 	struct mmc *mmc;
 	int ret;
 
@@ -1328,14 +1294,30 @@ int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg)
 		return -ENOMEM;
 	}
 
-	ret = fsl_esdhc_cfg_to_priv(cfg, priv);
-	if (ret) {
-		debug("%s xlate failure\n", __func__);
-		free(plat);
-		free(priv);
-		return ret;
+	priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
+	priv->sdhc_clk = cfg->sdhc_clk;
+	priv->wp_enable  = cfg->wp_enable;
+
+	mmc_cfg = &plat->cfg;
+
+	if (cfg->max_bus_width == 8) {
+		mmc_cfg->host_caps |= MMC_MODE_1BIT | MMC_MODE_4BIT |
+				      MMC_MODE_8BIT;
+	} else if (cfg->max_bus_width == 4) {
+		mmc_cfg->host_caps |= MMC_MODE_1BIT | MMC_MODE_4BIT;
+	} else if (cfg->max_bus_width == 1) {
+		mmc_cfg->host_caps |= MMC_MODE_1BIT;
+	} else {
+		mmc_cfg->host_caps |= MMC_MODE_1BIT | MMC_MODE_4BIT |
+				      MMC_MODE_8BIT;
+		printf("No max bus width provided. Assume 8-bit supported.\n");
 	}
 
+#ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK
+	if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK)
+		mmc_cfg->host_caps &= ~MMC_MODE_8BIT;
+#endif
+
 	ret = fsl_esdhc_init(priv, plat);
 	if (ret) {
 		debug("%s init failure\n", __func__);
@@ -1416,14 +1398,6 @@ static int fsl_esdhc_of_to_plat(struct udevice *dev)
 	priv->dev = dev;
 	priv->mode = -1;
 
-	val = dev_read_u32_default(dev, "bus-width", -1);
-	if (val == 8)
-		priv->bus_width = 8;
-	else if (val == 4)
-		priv->bus_width = 4;
-	else
-		priv->bus_width = 1;
-
 	val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1);
 	priv->tuning_step = val;
 	val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap",
@@ -1496,16 +1470,8 @@ static int fsl_esdhc_probe(struct udevice *dev)
 
 #if CONFIG_IS_ENABLED(OF_PLATDATA)
 	struct dtd_fsl_esdhc *dtplat = &plat->dtplat;
-	unsigned int val;
 
 	priv->esdhc_regs = map_sysmem(dtplat->reg[0], dtplat->reg[1]);
-	val = plat->dtplat.bus_width;
-	if (val == 8)
-		priv->bus_width = 8;
-	else if (val == 4)
-		priv->bus_width = 4;
-	else
-		priv->bus_width = 1;
 
 	if (dtplat->non_removable)
 		priv->non_removable = 1;
-- 
2.25.1



More information about the U-Boot mailing list