[PATCH] pci: Do not enable PCIe ASMedia ASM2824 workaround by default
Stefan Roese
sr at denx.de
Thu Apr 7 08:33:26 CEST 2022
On 4/6/22 17:09, Pali Rohár wrote:
> PCIe ASMedia ASM2824 workaround code unconditionally increase size of all
> SPL binaries with PCIe support, even those which do not use ASMedia ASM2824
> PCIe switch.
>
> Moreover this workaround is enabled for all existing hardware and also all
> future PCIe hardware, which opens a hole that other PCIe vendors may
> introduce same HW issue as ASMedia and nobody would notice it because
> U-Boot automatically apply workaround for it.
I agree, that we should not do this unconditionally in all cases,
without the option for users to disable this. Or even have it disabled
by default for most boards.
> Last iteration of Linux kernel patch for this workaround is bound just to
> ASMedia ASM2824 vendor+device id and not enabled on all PCIe hardware.
>
> So do not unconditionally enable PCIe ASMedia ASM2824 workaround on all
> hardware. Instead introduce a new config option which is disabled by
> default. This decrease SPL size and also ensure that workaround is not
> blindly or inexactly enabled.
>
> To make workaround code local, move it into separate file, so pci_auto.c
> contains only genetic auto configuration code.
>
> Signed-off-by: Pali Rohár <pali at kernel.org>
> ---
> Hello! What do you think about this change? I think it is good
> compromise between enable this workaround for all builds on all boards
> and enable it only based on device id. Or would it be better to restrict
> this workaround just for ASM2824 device like the last iteration of
> kernel patch?
I'm not sure if we should name this "workaround" ASM2824, even though
it's currently (only) targeted exactly for this PCIe switch. It might
be helpful for other PCIe switches as well. So perhaps it's better to
give this function a more generic name instead? With this change, it
makes perhaps also sense to keep this function in pci_auto.c but also
rename the Kconfig option to some more generic version.
Another comment below...
> ---
> drivers/pci/Kconfig | 6 +
> drivers/pci/Makefile | 1 +
> drivers/pci/pci_auto.c | 171 +-----------------------
> drivers/pci/pcie_asm2824_workaround.c | 183 ++++++++++++++++++++++++++
> 4 files changed, 194 insertions(+), 167 deletions(-)
> create mode 100644 drivers/pci/pcie_asm2824_workaround.c
>
> diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
> index 47cd074aa14c..16894929214a 100644
> --- a/drivers/pci/Kconfig
> +++ b/drivers/pci/Kconfig
> @@ -327,4 +327,10 @@ config PCIE_UNIPHIER
> Say Y here if you want to enable PCIe controller support on
> UniPhier SoCs.
>
> +config PCIE_ASM2824_WORKAROUND
> + bool "ASMedia ASM2824 PCIe workaround"
> + help
> + Say Y here if you want to enable link training failures for
> + ASMedia ASM2824 PCIe switch.
"to enable link training failures" sound misleading IMHO. Perhaps somthing
like this is better:
"...to enable link re-training upon failures for PCIe switches. This
seems to be helpful on the ASMedia ASM2824 PCIe switch."
Thanks,
Stefan
> +
> endif
> diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
> index 04f623652f09..4aa4e7c7285d 100644
> --- a/drivers/pci/Makefile
> +++ b/drivers/pci/Makefile
> @@ -50,3 +50,4 @@ obj-$(CONFIG_PCI_OCTEONTX) += pci_octeontx.o
> obj-$(CONFIG_PCIE_OCTEON) += pcie_octeon.o
> obj-$(CONFIG_PCIE_DW_SIFIVE) += pcie_dw_sifive.o
> obj-$(CONFIG_PCIE_UNIPHIER) += pcie_uniphier.o
> +obj-$(CONFIG_PCIE_ASM2824_WORKAROUND) += pcie_asm2824_workaround.o
> diff --git a/drivers/pci/pci_auto.c b/drivers/pci/pci_auto.c
> index c7968926a17f..851bf3bc55b1 100644
> --- a/drivers/pci/pci_auto.c
> +++ b/drivers/pci/pci_auto.c
> @@ -13,7 +13,6 @@
> #include <errno.h>
> #include <log.h>
> #include <pci.h>
> -#include <time.h>
> #include "pci_internal.h"
>
> /* the user can define CONFIG_SYS_PCI_CACHE_LINE_SIZE to avoid problems */
> @@ -182,167 +181,7 @@ static void dm_pciauto_setup_device(struct udevice *dev,
> dm_pci_write_config8(dev, PCI_LATENCY_TIMER, 0x80);
> }
>
> -/*
> - * Check if the link of a downstream PCIe port operates correctly.
> - *
> - * For that check if the optional Data Link Layer Link Active status gets
> - * on within a 200ms period or failing that wait until the completion of
> - * that period and check if link training has shown the completed status
> - * continuously throughout the second half of that period.
> - *
> - * Observation with the ASMedia ASM2824 Gen 3 switch indicates it takes
> - * 11-44ms to indicate the Data Link Layer Link Active status at 2.5GT/s,
> - * though it may take a couple of link training iterations.
> - */
> -static bool dm_pciauto_exp_link_stable(struct udevice *dev, int pcie_off)
> -{
> - u64 loops = 0, trcount = 0, ntrcount = 0, flips = 0;
> - bool dllla, lnktr, plnktr;
> - u16 exp_lnksta;
> - pci_dev_t bdf;
> - u64 end;
> -
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
> - plnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
> -
> - end = get_ticks() + usec_to_tick(200000);
> - do {
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA,
> - &exp_lnksta);
> - dllla = !!(exp_lnksta & PCI_EXP_LNKSTA_DLLLA);
> - lnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
> -
> - flips += plnktr ^ lnktr;
> - if (lnktr) {
> - ntrcount = 0;
> - trcount++;
> - } else {
> - ntrcount++;
> - }
> - loops++;
> -
> - plnktr = lnktr;
> - } while (!dllla && get_ticks() < end);
> -
> - bdf = dm_pci_get_bdf(dev);
> - debug("PCI Autoconfig: %02x.%02x.%02x: Fixup link: DL active: %u; "
> - "%3llu flips, %6llu loops of which %6llu while training, "
> - "final %6llu stable\n",
> - PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf),
> - (unsigned int)dllla,
> - (unsigned long long)flips, (unsigned long long)loops,
> - (unsigned long long)trcount, (unsigned long long)ntrcount);
> -
> - return dllla || ntrcount >= loops / 2;
> -}
> -
> -/*
> - * Retrain the link of a downstream PCIe port by hand if necessary.
> - *
> - * This is needed at least where a downstream port of the ASMedia ASM2824
> - * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304
> - * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 >
> - * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched
> - * board.
> - *
> - * In such a configuration the switches are supposed to negotiate the link
> - * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link
> - * continues switching between the two speeds indefinitely and the data
> - * link layer never reaches the active state, with link training reported
> - * repeatedly active ~84% of the time. Forcing the target link speed to
> - * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to
> - * each other correctly however. And more interestingly retraining with a
> - * higher target link speed afterwards lets the two successfully negotiate
> - * 5.0GT/s.
> - *
> - * As this can potentially happen with any device and is cheap in the case
> - * of correctly operating hardware, let's do it for all downstream ports,
> - * for root complexes, PCIe switches and PCI/PCI-X to PCIe bridges.
> - *
> - * First check if automatic link training may have failed to complete, as
> - * indicated by the optional Data Link Layer Link Active status being off
> - * and the Link Bandwidth Management Status indicating that hardware has
> - * changed the link speed or width in an attempt to correct unreliable
> - * link operation. If this is the case, then check if the link operates
> - * correctly by seeing whether it is being trained excessively. If it is,
> - * then conclude the link is broken.
> - *
> - * In that case restrict the speed to 2.5GT/s, observing that the Target
> - * Link Speed field is sticky and therefore the link will stay restricted
> - * even after a device reset is later made by an OS that is unaware of the
> - * problem. With the speed restricted request that the link be retrained
> - * and check again if the link operates correctly. If not, then set the
> - * Target Link Speed back to the original value.
> - *
> - * This requires the presence of the Link Control 2 register, so make sure
> - * the PCI Express Capability Version is at least 2. Also don't try, for
> - * obvious reasons, to limit the speed if 2.5GT/s is the only link speed
> - * supported.
> - */
> -static void dm_pciauto_exp_fixup_link(struct udevice *dev, int pcie_off)
> -{
> - u16 exp_lnksta, exp_lnkctl, exp_lnkctl2;
> - u16 exp_flags, exp_type, exp_version;
> - u32 exp_lnkcap;
> - pci_dev_t bdf;
> -
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_FLAGS, &exp_flags);
> - exp_version = exp_flags & PCI_EXP_FLAGS_VERS;
> - if (exp_version < 2)
> - return;
> -
> - exp_type = (exp_flags & PCI_EXP_FLAGS_TYPE) >> 4;
> - switch (exp_type) {
> - case PCI_EXP_TYPE_ROOT_PORT:
> - case PCI_EXP_TYPE_DOWNSTREAM:
> - case PCI_EXP_TYPE_PCIE_BRIDGE:
> - break;
> - default:
> - return;
> - }
> -
> - dm_pci_read_config32(dev, pcie_off + PCI_EXP_LNKCAP, &exp_lnkcap);
> - if ((exp_lnkcap & PCI_EXP_LNKCAP_SLS) <= PCI_EXP_LNKCAP_SLS_2_5GB)
> - return;
> -
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
> - if ((exp_lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) !=
> - PCI_EXP_LNKSTA_LBMS)
> - return;
> -
> - if (dm_pciauto_exp_link_stable(dev, pcie_off))
> - return;
> -
> - bdf = dm_pci_get_bdf(dev);
> - printf("PCI Autoconfig: %02x.%02x.%02x: "
> - "Downstream link non-functional\n",
> - PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> - printf("PCI Autoconfig: %02x.%02x.%02x: "
> - "Retrying with speed restricted to 2.5GT/s...\n",
> - PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> -
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL, &exp_lnkctl);
> - dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL2, &exp_lnkctl2);
> -
> - dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
> - (exp_lnkctl2 & ~PCI_EXP_LNKCTL2_TLS) |
> - PCI_EXP_LNKCTL2_TLS_2_5GT);
> - dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
> - exp_lnkctl | PCI_EXP_LNKCTL_RL);
> -
> - if (dm_pciauto_exp_link_stable(dev, pcie_off)) {
> - printf("PCI Autoconfig: %02x.%02x.%02x: Succeeded!\n",
> - PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> - } else {
> - printf("PCI Autoconfig: %02x.%02x.%02x: Failed!\n",
> - PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> -
> - dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
> - exp_lnkctl2);
> - dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
> - exp_lnkctl | PCI_EXP_LNKCTL_RL);
> - }
> -}
> +void pcie_asm2824_workaround(struct udevice *dev);
>
> void dm_pciauto_prescan_setup_bridge(struct udevice *dev, int sub_bus)
> {
> @@ -353,7 +192,6 @@ void dm_pciauto_prescan_setup_bridge(struct udevice *dev, int sub_bus)
> u8 io_32;
> struct udevice *ctlr = pci_get_controller(dev);
> struct pci_controller *ctlr_hose = dev_get_uclass_priv(ctlr);
> - int pcie_off;
>
> pci_mem = ctlr_hose->pci_mem;
> pci_prefetch = ctlr_hose->pci_prefetch;
> @@ -440,10 +278,9 @@ void dm_pciauto_prescan_setup_bridge(struct udevice *dev, int sub_bus)
> }
> }
>
> - /* For PCIe devices see if we need to retrain the link by hand */
> - pcie_off = dm_pci_find_capability(dev, PCI_CAP_ID_EXP);
> - if (pcie_off)
> - dm_pciauto_exp_fixup_link(dev, pcie_off);
> +#ifdef CONFIG_PCIE_ASM2824_WORKAROUND
> + pcie_asm2824_workaround(dev);
> +#endif
>
> /* Enable memory and I/O accesses, enable bus master */
> dm_pci_write_config16(dev, PCI_COMMAND, cmdstat | PCI_COMMAND_MASTER);
> diff --git a/drivers/pci/pcie_asm2824_workaround.c b/drivers/pci/pcie_asm2824_workaround.c
> new file mode 100644
> index 000000000000..9415346faf22
> --- /dev/null
> +++ b/drivers/pci/pcie_asm2824_workaround.c
> @@ -0,0 +1,183 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * ASMedia ASM2824 PCIe workaround
> + *
> + * Copyright (c) 2021 Maciej W. Rozycki <macro at orcam.me.uk>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <pci.h>
> +#include <time.h>
> +
> +/*
> + * Check if the link of a downstream PCIe port operates correctly.
> + *
> + * For that check if the optional Data Link Layer Link Active status gets
> + * on within a 200ms period or failing that wait until the completion of
> + * that period and check if link training has shown the completed status
> + * continuously throughout the second half of that period.
> + *
> + * Observation with the ASMedia ASM2824 Gen 3 switch indicates it takes
> + * 11-44ms to indicate the Data Link Layer Link Active status at 2.5GT/s,
> + * though it may take a couple of link training iterations.
> + */
> +static bool dm_pciauto_exp_link_stable(struct udevice *dev, int pcie_off)
> +{
> + u64 loops = 0, trcount = 0, ntrcount = 0, flips = 0;
> + bool dllla, lnktr, plnktr;
> + u16 exp_lnksta;
> + pci_dev_t bdf;
> + u64 end;
> +
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
> + plnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
> +
> + end = get_ticks() + usec_to_tick(200000);
> + do {
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA,
> + &exp_lnksta);
> + dllla = !!(exp_lnksta & PCI_EXP_LNKSTA_DLLLA);
> + lnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
> +
> + flips += plnktr ^ lnktr;
> + if (lnktr) {
> + ntrcount = 0;
> + trcount++;
> + } else {
> + ntrcount++;
> + }
> + loops++;
> +
> + plnktr = lnktr;
> + } while (!dllla && get_ticks() < end);
> +
> + bdf = dm_pci_get_bdf(dev);
> + debug("PCI Autoconfig: %02x.%02x.%02x: Fixup link: DL active: %u; "
> + "%3llu flips, %6llu loops of which %6llu while training, "
> + "final %6llu stable\n",
> + PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf),
> + (unsigned int)dllla,
> + (unsigned long long)flips, (unsigned long long)loops,
> + (unsigned long long)trcount, (unsigned long long)ntrcount);
> +
> + return dllla || ntrcount >= loops / 2;
> +}
> +
> +/*
> + * Retrain the link of a downstream PCIe port by hand if necessary.
> + *
> + * This is needed at least where a downstream port of the ASMedia ASM2824
> + * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304
> + * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 >
> + * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched
> + * board.
> + *
> + * In such a configuration the switches are supposed to negotiate the link
> + * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link
> + * continues switching between the two speeds indefinitely and the data
> + * link layer never reaches the active state, with link training reported
> + * repeatedly active ~84% of the time. Forcing the target link speed to
> + * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to
> + * each other correctly however. And more interestingly retraining with a
> + * higher target link speed afterwards lets the two successfully negotiate
> + * 5.0GT/s.
> + *
> + * As this can potentially happen with any device and is cheap in the case
> + * of correctly operating hardware, let's do it for all downstream ports,
> + * for root complexes, PCIe switches and PCI/PCI-X to PCIe bridges.
> + *
> + * First check if automatic link training may have failed to complete, as
> + * indicated by the optional Data Link Layer Link Active status being off
> + * and the Link Bandwidth Management Status indicating that hardware has
> + * changed the link speed or width in an attempt to correct unreliable
> + * link operation. If this is the case, then check if the link operates
> + * correctly by seeing whether it is being trained excessively. If it is,
> + * then conclude the link is broken.
> + *
> + * In that case restrict the speed to 2.5GT/s, observing that the Target
> + * Link Speed field is sticky and therefore the link will stay restricted
> + * even after a device reset is later made by an OS that is unaware of the
> + * problem. With the speed restricted request that the link be retrained
> + * and check again if the link operates correctly. If not, then set the
> + * Target Link Speed back to the original value.
> + *
> + * This requires the presence of the Link Control 2 register, so make sure
> + * the PCI Express Capability Version is at least 2. Also don't try, for
> + * obvious reasons, to limit the speed if 2.5GT/s is the only link speed
> + * supported.
> + */
> +static void dm_pciauto_exp_fixup_link(struct udevice *dev, int pcie_off)
> +{
> + u16 exp_lnksta, exp_lnkctl, exp_lnkctl2;
> + u16 exp_flags, exp_type, exp_version;
> + u32 exp_lnkcap;
> + pci_dev_t bdf;
> +
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_FLAGS, &exp_flags);
> + exp_version = exp_flags & PCI_EXP_FLAGS_VERS;
> + if (exp_version < 2)
> + return;
> +
> + exp_type = (exp_flags & PCI_EXP_FLAGS_TYPE) >> 4;
> + switch (exp_type) {
> + case PCI_EXP_TYPE_ROOT_PORT:
> + case PCI_EXP_TYPE_DOWNSTREAM:
> + case PCI_EXP_TYPE_PCIE_BRIDGE:
> + break;
> + default:
> + return;
> + }
> +
> + dm_pci_read_config32(dev, pcie_off + PCI_EXP_LNKCAP, &exp_lnkcap);
> + if ((exp_lnkcap & PCI_EXP_LNKCAP_SLS) <= PCI_EXP_LNKCAP_SLS_2_5GB)
> + return;
> +
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
> + if ((exp_lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) !=
> + PCI_EXP_LNKSTA_LBMS)
> + return;
> +
> + if (dm_pciauto_exp_link_stable(dev, pcie_off))
> + return;
> +
> + bdf = dm_pci_get_bdf(dev);
> + printf("PCI Autoconfig: %02x.%02x.%02x: "
> + "Downstream link non-functional\n",
> + PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> + printf("PCI Autoconfig: %02x.%02x.%02x: "
> + "Retrying with speed restricted to 2.5GT/s...\n",
> + PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> +
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL, &exp_lnkctl);
> + dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL2, &exp_lnkctl2);
> +
> + dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
> + (exp_lnkctl2 & ~PCI_EXP_LNKCTL2_TLS) |
> + PCI_EXP_LNKCTL2_TLS_2_5GT);
> + dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
> + exp_lnkctl | PCI_EXP_LNKCTL_RL);
> +
> + if (dm_pciauto_exp_link_stable(dev, pcie_off)) {
> + printf("PCI Autoconfig: %02x.%02x.%02x: Succeeded!\n",
> + PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> + } else {
> + printf("PCI Autoconfig: %02x.%02x.%02x: Failed!\n",
> + PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
> +
> + dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
> + exp_lnkctl2);
> + dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
> + exp_lnkctl | PCI_EXP_LNKCTL_RL);
> + }
> +}
> +
> +void pcie_asm2824_workaround(struct udevice *dev)
> +{
> + int pcie_off;
> +
> + /* For PCIe devices see if we need to retrain the link by hand */
> + pcie_off = dm_pci_find_capability(dev, PCI_CAP_ID_EXP);
> + if (pcie_off)
> + dm_pciauto_exp_fixup_link(dev, pcie_off);
> +}
Viele Grüße,
Stefan Roese
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list