[PATCH v3 4/4] mvebu: uDPU: update defconfig

[Stefan Roese]

On 3/24/22 10:57, Robert Marko wrote:
> Update the current uDPU defconfig with following changes:
> * Disable CONFIG_SPI_BOOT, its not needed for booting and the device boots
> from eMMC anyway.
> * Disable CONFIG_SYS_CONSOLE_INFO_QUIET, there is no need to diverge from
> other boards by not priting the console device
> * Enable CONFIG_CMD_MTD in order to allow use of the MTD tool
> * Disable CONFIG_CMD_MTDPARTS, with MTD now being able to parse partitions
> from DTS there is no need for it, the default MTDPARTS were incorrect
> anyway
> * Enable CONFIG_MMC_HS200_SUPPORT, the eMMC used support both HS200 and
> HS400 modes, so enable at least HS200 because Xenon driver does not
> support HS400 currently
> * Replace CONFIG_SPI_FLASH_BAR with CONFIG_SPI_FLASH_SFDP_SUPPORT
> Utilize SFDP parsing instead of relying on the extended address registers
> 
> Signed-off-by: Robert Marko <robert.marko at sartura.hr>

Reviewed-by: Stefan Roese <sr at denx.de>

Thanks,
Stefan

> ---
>   configs/uDPU_defconfig | 10 ++++------
>   1 file changed, 4 insertions(+), 6 deletions(-)
> 
> diff --git a/configs/uDPU_defconfig b/configs/uDPU_defconfig
> index b5f2115e63..1a2182b823 100644
> --- a/configs/uDPU_defconfig
> +++ b/configs/uDPU_defconfig
> @@ -16,9 +16,8 @@ CONFIG_DISTRO_DEFAULTS=y
>   # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
>   CONFIG_SYS_LOAD_ADDR=0x6000000
>   CONFIG_FIT=y
> -CONFIG_SPI_BOOT=y
> +CONFIG_FIT_VERBOSE=y
>   CONFIG_USE_PREBOOT=y
> -CONFIG_SYS_CONSOLE_INFO_QUIET=y
>   # CONFIG_DISPLAY_CPUINFO is not set
>   # CONFIG_DISPLAY_BOARDINFO is not set
>   CONFIG_DISPLAY_BOARDINFO_LATE=y
> @@ -32,6 +31,7 @@ CONFIG_SYS_PROMPT="uDPU>> "
>   CONFIG_CMD_GPIO=y
>   CONFIG_CMD_I2C=y
>   CONFIG_CMD_MMC=y
> +CONFIG_CMD_MTD=y
>   CONFIG_CMD_PCI=y
>   CONFIG_CMD_SPI=y
>   CONFIG_CMD_USB=y
> @@ -41,9 +41,6 @@ CONFIG_CMD_CACHE=y
>   CONFIG_CMD_TIME=y
>   CONFIG_CMD_MVEBU_BUBT=y
>   CONFIG_CMD_EXT4_WRITE=y
> -CONFIG_CMD_MTDPARTS=y
> -CONFIG_MTDIDS_DEFAULT="nor0=spi0"
> -CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0:4m(uboot),-(rootfs)"
>   CONFIG_MAC_PARTITION=y
>   CONFIG_ENV_OVERWRITE=y
>   CONFIG_ENV_IS_IN_SPI_FLASH=y
> @@ -56,12 +53,13 @@ CONFIG_DM_I2C=y
>   CONFIG_DM_I2C_GPIO=y
>   CONFIG_SYS_I2C_MV=y
>   CONFIG_MISC=y
> +CONFIG_MMC_HS200_SUPPORT=y
>   CONFIG_MMC_SDHCI=y
>   CONFIG_MMC_SDHCI_SDMA=y
>   CONFIG_MMC_SDHCI_XENON=y
>   CONFIG_MTD=y
>   CONFIG_DM_MTD=y
> -CONFIG_SPI_FLASH_BAR=y
> +CONFIG_SPI_FLASH_SFDP_SUPPORT=y
>   CONFIG_SPI_FLASH_MACRONIX=y
>   CONFIG_SPI_FLASH_SPANSION=y
>   CONFIG_SPI_FLASH_STMICRO=y

Viele Grüße,
Stefan Roese

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de