[PATCH 2/2] usb: dwc3: Implement .glue_configure for i.MX8MP

[Tim Harvey]

On Fri, Apr 1, 2022 at 7:32 AM Marek Vasut <marex at denx.de> wrote:
>
> The i.MX8MP glue needs to be configured based on a couple of DT
> properties, implement .glue_configure callback to parse those DT
> properties and configure the glue accordingly.
>
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Angus Ainslie <angus at akkea.ca>
> Cc: Bin Meng <bmeng.cn at gmail.com>
> Cc: Fabio Estevam <festevam at gmail.com>
> Cc: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
> Cc: Michal Simek <michal.simek at xilinx.com>
> Cc: Peng Fan <peng.fan at nxp.com>
> Cc: Stefano Babic <sbabic at denx.de>
> ---
>  drivers/usb/dwc3/dwc3-generic.c | 52 +++++++++++++++++++++++++++++++++
>  1 file changed, 52 insertions(+)
>
> diff --git a/drivers/usb/dwc3/dwc3-generic.c b/drivers/usb/dwc3/dwc3-generic.c
> index 7e3814207e4..6cf844cb483 100644
> --- a/drivers/usb/dwc3/dwc3-generic.c
> +++ b/drivers/usb/dwc3/dwc3-generic.c
> @@ -223,6 +223,57 @@ struct dwc3_glue_ops {
>                                enum usb_dr_mode mode);
>  };
>
> +void dwc3_imx8mp_glue_configure(struct udevice *dev, int index,
> +                               enum usb_dr_mode mode)
> +{
> +/* USB glue registers */
> +#define USB_CTRL0              0x00
> +#define USB_CTRL1              0x04
> +
> +#define USB_CTRL0_PORTPWR_EN   BIT(12) /* 1 - PPC enabled (default) */
> +#define USB_CTRL0_USB3_FIXED   BIT(22) /* 1 - USB3 permanent attached */
> +#define USB_CTRL0_USB2_FIXED   BIT(23) /* 1 - USB2 permanent attached */
> +
> +#define USB_CTRL1_OC_POLARITY  BIT(16) /* 0 - HIGH / 1 - LOW */
> +#define USB_CTRL1_PWR_POLARITY BIT(17) /* 0 - HIGH / 1 - LOW */
> +       fdt_addr_t regs = dev_read_addr_index(dev, 1);
> +       void *base = map_physmem(regs, 0x8, MAP_NOCACHE);
> +       u32 value;
> +
> +       value = readl(base + USB_CTRL0);
> +
> +       if (dev_read_bool(dev, "fsl,permanently-attached"))
> +               value |= (USB_CTRL0_USB2_FIXED | USB_CTRL0_USB3_FIXED);
> +       else
> +               value &= ~(USB_CTRL0_USB2_FIXED | USB_CTRL0_USB3_FIXED);
> +
> +       if (dev_read_bool(dev, "fsl,disable-port-power-control"))
> +               value &= ~(USB_CTRL0_PORTPWR_EN);
> +       else
> +               value |= USB_CTRL0_PORTPWR_EN;
> +
> +       writel(value, base + USB_CTRL0);
> +
> +       value = readl(base + USB_CTRL1);
> +       if (dev_read_bool(dev, "fsl,over-current-active-low"))
> +               value |= USB_CTRL1_OC_POLARITY;
> +       else
> +               value &= ~USB_CTRL1_OC_POLARITY;
> +
> +       if (dev_read_bool(dev, "fsl,power-active-low"))
> +               value |= USB_CTRL1_PWR_POLARITY;
> +       else
> +               value &= ~USB_CTRL1_PWR_POLARITY;
> +
> +       writel(value, base + USB_CTRL1);
> +
> +       unmap_physmem(base, MAP_NOCACHE);
> +}
> +
> +struct dwc3_glue_ops imx8mp_ops = {
> +       .glue_configure = dwc3_imx8mp_glue_configure,
> +};
> +
>  void dwc3_ti_glue_configure(struct udevice *dev, int index,
>                             enum usb_dr_mode mode)
>  {
> @@ -464,6 +515,7 @@ static const struct udevice_id dwc3_glue_ids[] = {
>         { .compatible = "rockchip,rk3328-dwc3" },
>         { .compatible = "rockchip,rk3399-dwc3" },
>         { .compatible = "qcom,dwc3" },
> +       { .compatible = "fsl,imx8mp-dwc3", .data = (ulong)&imx8mp_ops },
>         { .compatible = "fsl,imx8mq-dwc3" },
>         { .compatible = "intel,tangier-dwc3" },
>         { }
> --
> 2.35.1
>

Thanks for working on this!

This helps get DWC3 USB working on IMX8MP.

For both patches in this series:
Tested-By: Tim Harvey <tharvey at gateworks.com> #imx8mp-venice-gw74xx

Best Regards,

Tim