[PATCH] tools/mrvl_uart.sh: Remove script

[Stefan Roese]

On 2/3/22 17:50, Pali Rohár wrote:
> There are two tools for sending images over UART to Marvell SoCs: kwboot
> and mrvl_uart.sh. kwboot received lot of new features and improvements in
> last few months. There is no need to maintain two tools in U-Boot, so
> remove old mrvl_uart.sh tool.
> 
> Signed-off-by: Pali Rohár <pali at kernel.org>
> ---
>   tools/mrvl_uart.sh | 119 ---------------------------------------------
>   1 file changed, 119 deletions(-)
>   delete mode 100755 tools/mrvl_uart.sh

Applied to u-boot-marvell/master

Thanks,
Stefan

> diff --git a/tools/mrvl_uart.sh b/tools/mrvl_uart.sh
> deleted file mode 100755
> index a46411fc99fb..000000000000
> --- a/tools/mrvl_uart.sh
> +++ /dev/null
> @@ -1,119 +0,0 @@
> -#!/bin/bash
> -# SPDX-License-Identifier: GPL-2.0
> -#
> -######################################################
> -# Copyright (C) 2016 Marvell International Ltd.
> -#
> -# https://spdx.org/licenses
> -#
> -# Author: Konstantin Porotchkin kostap at marvell.com
> -#
> -# Version 0.3
> -#
> -# UART recovery downloader for Armada SoCs
> -#
> -######################################################
> -
> -port=$1
> -file=$2
> -speed=$3
> -
> -pattern_repeat=1500
> -default_baudrate=115200
> -tmpfile=/tmp/xmodem.pattern
> -tools=( dd stty sx minicom )
> -
> -case "$3" in
> -    2)
> -        fast_baudrate=230400
> -        prefix="\xF2"
> -        ;;
> -    4)
> -        fast_baudrate=460800
> -        prefix="\xF4"
> -        ;;
> -    8)
> -    	fast_baudrate=921600
> -        prefix="\xF8"
> -        ;;
> -    *)
> -    	fast_baudrate=$default_baudrate
> -        prefix="\xBB"
> -esac
> -
> -if [[ -z "$port" || -z "$file" ]]
> -then
> -    echo -e "\nMarvell recovery image downloader for Armada SoC family."
> -    echo -e "Command syntax:"
> -    echo -e "\t$(basename $0) <port> <file> [2|4|8]"
> -    echo -e "\tport  - serial port the target board is connected to"
> -    echo -e "\tfile  - recovery boot image for target download"
> -    echo -e "\t2|4|8 - times to increase the default serial port speed by"
> -    echo -e "For example - load the image over ttyUSB0 @ 460800 baud:"
> -    echo -e "$(basename $0) /dev/ttyUSB0 /tmp/flash-image.bin 4\n"
> -    echo -e "=====WARNING====="
> -    echo -e "- The speed-up option is not available in SoC families prior to A8K+"
> -    echo -e "- This utility is not compatible with Armada 37xx SoC family\n"
> -fi
> -
> -# Sanity checks
> -if [ -c "$port" ]
> -then
> -   echo -e "Using device connected on serial port \"$port\""
> -else
> -   echo "Wrong serial port name!"
> -   exit 1
> -fi
> -
> -if [ -f "$file" ]
> -then
> -   echo -e "Loading flash image file \"$file\""
> -else
> -   echo "File $file does not exist!"
> -   exit 1
> -fi
> -
> -# Verify required tools installation
> -for tool in ${tools[@]}
> -do
> -    toolname=`which $tool`
> -    if [ -z "$toolname" ]
> -    then
> -        echo -e "Missing installation of \"$tool\" --> Exiting"
> -        exit 1
> -    fi
> -done
> -
> -
> -echo -e "Recovery will run at $fast_baudrate baud"
> -echo -e "========================================"
> -
> -if [ -f "$tmpfile" ]
> -then
> -    rm -f $tmpfile
> -fi
> -
> -# Send the escape sequence to target board using default debug port speed
> -stty -F $port raw ignbrk time 5 $default_baudrate
> -counter=0
> -while [ $counter -lt $pattern_repeat ]; do
> -    echo -n -e "$prefix\x11\x22\x33\x44\x55\x66\x77" >> $tmpfile
> -    let counter=counter+1
> -done
> -
> -echo -en "Press the \"Reset\" button on the target board and "
> -echo -en "the \"Enter\" key on the host keyboard simultaneously"
> -read
> -dd if=$tmpfile of=$port &>/dev/null
> -
> -# Speed up the binary image transfer
> -stty -F $port raw ignbrk time 5 $fast_baudrate
> -sx -vv $file > $port < $port
> -#sx-at91 $port $file
> -
> -# Return the port to the default speed
> -stty -F $port raw ignbrk time 5 $default_baudrate
> -
> -# Optional - fire up Minicom
> -minicom -D $port -b $default_baudrate
> -

Viele Grüße,
Stefan Roese

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de