[PATCH u-boot-marvell 15/19] net: mvneta: Convert to use PHY_FIXED for fixed-link
Marek Behún
kabel at kernel.org
Wed Apr 27 12:41:58 CEST 2022
From: Marek Behún <marek.behun at nic.cz>
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.
Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.
Signed-off-by: Marek Behún <marek.behun at nic.cz>
---
configs/mvebu_espressobin-88f3720_defconfig | 1 +
configs/turris_omnia_defconfig | 1 +
drivers/net/mvneta.c | 98 ++++++++-------------
3 files changed, 39 insertions(+), 61 deletions(-)
diff --git a/configs/mvebu_espressobin-88f3720_defconfig b/configs/mvebu_espressobin-88f3720_defconfig
index 37e4fdc41e..8d7d57ff1b 100644
--- a/configs/mvebu_espressobin-88f3720_defconfig
+++ b/configs/mvebu_espressobin-88f3720_defconfig
@@ -74,6 +74,7 @@ CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
CONFIG_MVNETA=y
diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig
index 6b218bd7a7..bdd70f2ba7 100644
--- a/configs/turris_omnia_defconfig
+++ b/configs/turris_omnia_defconfig
@@ -79,6 +79,7 @@ CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
CONFIG_PHY_GIGE=y
CONFIG_MVNETA=y
CONFIG_MII=y
diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
index 519e06ff01..5b1c4fe5fc 100644
--- a/drivers/net/mvneta.c
+++ b/drivers/net/mvneta.c
@@ -1152,11 +1152,6 @@ static void mvneta_adjust_link(struct udevice *dev)
struct phy_device *phydev = pp->phydev;
bool status_change = false;
- if (pp->fixed_link) {
- debug("Using fixed link, skip link adjust\n");
- return;
- }
-
if (phydev->link &&
(pp->speed != phydev->speed || pp->duplex != phydev->duplex)) {
u32 val;
@@ -1168,6 +1163,21 @@ static void mvneta_adjust_link(struct udevice *dev)
MVNETA_GMAC_AN_SPEED_EN |
MVNETA_GMAC_AN_DUPLEX_EN);
+ /* FIXME: For fixed-link case, these were the initial settings
+ * used before the code was converted to use PHY_FIXED. Some of
+ * these may look nonsensical (for example BYPASS_AN makes sense
+ * for 1000base-x and 2500base-x modes, AFAIK), and in fact this
+ * may be changed in the future (when support for inband AN will
+ * be added). Also, why is ADVERT_FC enabled if we don't enable
+ * inband AN at all?
+ */
+ if (pp->fixed_link)
+ val = MVNETA_GMAC_FORCE_LINK_UP |
+ MVNETA_GMAC_IB_BYPASS_AN_EN |
+ MVNETA_GMAC_SET_FC_EN |
+ MVNETA_GMAC_ADVERT_FC_EN |
+ MVNETA_GMAC_SAMPLE_TX_CFG_EN;
+
if (phydev->duplex)
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
@@ -1413,56 +1423,34 @@ static int mvneta_start(struct udevice *dev)
mvneta_port_power_up(pp, pp->phy_interface);
if (!pp->init || pp->link == 0) {
- if (pp->fixed_link) {
- u32 val;
-
- pp->init = 1;
- pp->link = 1;
- mvneta_init(dev);
-
- val = MVNETA_GMAC_FORCE_LINK_UP |
- MVNETA_GMAC_IB_BYPASS_AN_EN |
- MVNETA_GMAC_SET_FC_EN |
- MVNETA_GMAC_ADVERT_FC_EN |
- MVNETA_GMAC_SAMPLE_TX_CFG_EN;
-
- if (pp->duplex)
- val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
-
- if (pp->speed == SPEED_1000)
- val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
- else if (pp->speed == SPEED_100)
- val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+ phydev = dm_eth_phy_connect(dev);
+ if (!phydev) {
+ printf("dm_eth_phy_connect failed\n");
+ return -ENODEV;
+ }
- mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
- } else {
- phydev = dm_eth_phy_connect(dev);
- if (!phydev) {
- printf("dm_eth_phy_connect failed\n");
- return -ENODEV;
- }
+ pp->fixed_link = phydev->phy_id == PHY_FIXED_ID;
- /* Set PHY address in case we will enable HW polling */
+ /* Set PHY address in case we will enable HW polling */
+ if (!pp->fixed_link)
mvreg_write(pp, MVNETA_PHY_ADDR, phydev->addr);
- pp->phydev = phydev;
- phy_config(phydev);
- phy_startup(phydev);
- if (!phydev->link) {
- printf("%s: No link.\n", phydev->dev->name);
- return -1;
- }
-
- /* Full init on first call */
- mvneta_init(dev);
- pp->init = 1;
- return 0;
+ pp->phydev = phydev;
+ phy_config(phydev);
+ phy_startup(phydev);
+ if (!phydev->link) {
+ printf("%s: No link.\n", phydev->dev->name);
+ return -1;
}
- }
- /* Upon all following calls, this is enough */
- mvneta_port_up(pp);
- mvneta_port_enable(pp);
+ /* Full init on first call */
+ mvneta_init(dev);
+ pp->init = 1;
+ } else {
+ /* Upon all following calls, this is enough */
+ mvneta_port_up(pp);
+ mvneta_port_enable(pp);
+ }
return 0;
}
@@ -1560,10 +1548,7 @@ static int mvneta_probe(struct udevice *dev)
#if CONFIG_IS_ENABLED(DM_GPIO)
struct ofnode_phandle_args sfp_args;
#endif
- void *blob = (void *)gd->fdt_blob;
- int node = dev_of_offset(dev);
void *bd_space;
- int fl_node;
/*
* Allocate buffer area for descs and rx_buffers. This is only
@@ -1600,15 +1585,6 @@ static int mvneta_probe(struct udevice *dev)
else
mvneta_conf_mbus_windows(pp);
- /* fetch 'fixed-link' property from 'neta' node */
- fl_node = fdt_subnode_offset(blob, node, "fixed-link");
- if (fl_node != -FDT_ERR_NOTFOUND) {
- /* set phy_addr to invalid value for fixed link */
- pp->duplex = fdtdec_get_bool(blob, fl_node, "full-duplex");
- pp->speed = fdtdec_get_int(blob, fl_node, "speed", 0);
- pp->fixed_link = true;
- }
-
#if CONFIG_IS_ENABLED(DM_GPIO)
if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
ofnode_is_enabled(sfp_args.node))
--
2.35.1
More information about the U-Boot
mailing list