[PATCH 07/15] imx: imx8m[m/p]_phycore: Enable DM_SERIAL
Peng Fan (OSS)
peng.fan at oss.nxp.com
Sat Apr 30 14:43:09 CEST 2022
From: Peng Fan <peng.fan at nxp.com>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
board/phytec/phycore_imx8mm/spl.c | 12 ++----------
board/phytec/phycore_imx8mp/spl.c | 8 --------
configs/phycore-imx8mm_defconfig | 1 +
configs/phycore-imx8mp_defconfig | 1 +
include/configs/phycore_imx8mm.h | 3 ---
include/configs/phycore_imx8mp.h | 3 ---
6 files changed, 4 insertions(+), 24 deletions(-)
diff --git a/board/phytec/phycore_imx8mm/spl.c b/board/phytec/phycore_imx8mm/spl.c
index d54145ef995..7f24a3affc8 100644
--- a/board/phytec/phycore_imx8mm/spl.c
+++ b/board/phytec/phycore_imx8mm/spl.c
@@ -57,14 +57,8 @@ int board_fit_config_name_match(const char *name)
return 0;
}
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE)
-static iomux_v3_cfg_t const uart_pads[] = {
- IMX8MM_PAD_UART3_RXD_UART3_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- IMX8MM_PAD_UART3_TXD_UART3_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@@ -77,8 +71,6 @@ int board_early_init_f(void)
set_wdog_reset(wdog);
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-
return 0;
}
@@ -92,8 +84,6 @@ void board_init_f(ulong dummy)
board_early_init_f();
- preloader_console_init();
-
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
@@ -103,6 +93,8 @@ void board_init_f(ulong dummy)
hang();
}
+ preloader_console_init();
+
enable_tzc380();
/* DDR initialization */
diff --git a/board/phytec/phycore_imx8mp/spl.c b/board/phytec/phycore_imx8mp/spl.c
index 19c486e5517..38a581bef57 100644
--- a/board/phytec/phycore_imx8mp/spl.c
+++ b/board/phytec/phycore_imx8mp/spl.c
@@ -89,14 +89,8 @@ int board_fit_config_name_match(const char *name)
return 0;
}
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
-static iomux_v3_cfg_t const uart_pads[] = {
- MX8MP_PAD_UART1_RXD__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX8MP_PAD_UART1_TXD__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const wdog_pads[] = {
MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@@ -109,8 +103,6 @@ int board_early_init_f(void)
set_wdog_reset(wdog);
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-
return 0;
}
diff --git a/configs/phycore-imx8mm_defconfig b/configs/phycore-imx8mm_defconfig
index ba5833f7060..9da222afc54 100644
--- a/configs/phycore-imx8mm_defconfig
+++ b/configs/phycore-imx8mm_defconfig
@@ -107,6 +107,7 @@ CONFIG_PINCTRL_IMX8M=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
diff --git a/configs/phycore-imx8mp_defconfig b/configs/phycore-imx8mp_defconfig
index 86d0f4df7f6..a851b1bdccb 100644
--- a/configs/phycore-imx8mp_defconfig
+++ b/configs/phycore-imx8mp_defconfig
@@ -98,6 +98,7 @@ CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_POWER_I2C=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
CONFIG_SPL_SYSRESET=y
diff --git a/include/configs/phycore_imx8mm.h b/include/configs/phycore_imx8mm.h
index 71f0c42ec0c..564b8125ba3 100644
--- a/include/configs/phycore_imx8mm.h
+++ b/include/configs/phycore_imx8mm.h
@@ -83,9 +83,6 @@
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE SZ_2G /* 2GB DDR */
-/* UART */
-#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR
-
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE SZ_2K
#define CONFIG_SYS_MAXARGS 64
diff --git a/include/configs/phycore_imx8mp.h b/include/configs/phycore_imx8mp.h
index 0c963b62b3b..3e4315f2b81 100644
--- a/include/configs/phycore_imx8mp.h
+++ b/include/configs/phycore_imx8mp.h
@@ -83,9 +83,6 @@
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0x80000000
-/* UART */
-#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
-
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE SZ_2K
#define CONFIG_SYS_MAXARGS 64
--
2.36.0
More information about the U-Boot
mailing list