[PATCH v3 1/3] net: NC-SI setup and handling
Ramon Fried
rfried.dev at gmail.com
Mon Aug 8 10:24:30 CEST 2022
On Mon, Aug 8, 2022 at 9:18 AM Joel Stanley <joel at jms.id.au> wrote:
>
> On Sat, 6 Aug 2022 at 23:54, Ramon Fried <rfried.dev at gmail.com> wrote:
> >
> > On Mon, Jul 4, 2022 at 11:20 AM Cédric Le Goater <clg at kaod.org> wrote:
> > >
> > > On 7/4/22 09:58, Joel Stanley wrote:
> > > > From: Samuel Mendoza-Jonas <sam at mendozajonas.com>
> > > >
> > > > Add the handling of NC-SI ethernet frames, and add a check at the start
> > > > of net_loop() to configure NC-SI before starting other network commands.
> > > > This also adds an "ncsi" command to manually start NC-SI configuration.
> > > >
> > > > Signed-off-by: Samuel Mendoza-Jonas <sam at mendozajonas.com>
> > > > Signed-off-by: Joel Stanley <joel at jms.id.au>
> > >
> > >
> > > Reviewed-by: Cédric Le Goater <clg at kaod.org>
> > >
> > > Thanks,
> > >
> > > C.
> > >
> > > > ---
> > > > v3:
> > > > - Fix compilation. There were no configs that enabled the NCSI phy code
> > > > so it had bitrotted
> > > > - Use NCSI_PHY instead of CMD_NCSI so NCSI can work without the command
> > > > - Add phy_interface_is_ncsi() helper, thanks Cédric for this suggestion
> > > > - Only create NCSI phy device when driver is configured for it
> > > >
> > > > include/net.h | 2 +-
> > > > include/phy.h | 2 ++
> > > > cmd/net.c | 22 ++++++++++++++++++++++
> > > > drivers/net/phy/ncsi.c | 1 +
> > > > drivers/net/phy/phy.c | 9 ++++++++-
> > > > net/net.c | 27 ++++++++++++++++++++++++++-
> > > > cmd/Kconfig | 8 ++++++++
> > > > 7 files changed, 68 insertions(+), 3 deletions(-)
> > > >
> > > > diff --git a/include/net.h b/include/net.h
> > > > index e3889a0bc85e..0681b8246323 100644
> > > > --- a/include/net.h
> > > > +++ b/include/net.h
> > > > @@ -558,7 +558,7 @@ extern int net_restart_wrap; /* Tried all network devices */
> > > >
> > > > enum proto_t {
> > > > BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP,
> > > > - TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL, UDP
> > > > + TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL, UDP, NCSI
> > > > };
> > > >
> > > > extern char net_boot_file_name[1024];/* Boot File name */
> > > > diff --git a/include/phy.h b/include/phy.h
> > > > index b32959571069..1e0f8856f629 100644
> > > > --- a/include/phy.h
> > > > +++ b/include/phy.h
> > > > @@ -583,6 +583,8 @@ static inline bool phy_interface_is_sgmii(struct phy_device *phydev)
> > > > phydev->interface <= PHY_INTERFACE_MODE_QSGMII;
> > > > }
> > > >
> > > > +bool phy_interface_is_ncsi(void);
> > > > +
> > > > /* PHY UIDs for various PHYs that are referenced in external code */
> > > > #define PHY_UID_CS4340 0x13e51002
> > > > #define PHY_UID_CS4223 0x03e57003
> > > > diff --git a/cmd/net.c b/cmd/net.c
> > > > index 3619c843d838..2863fe768118 100644
> > > > --- a/cmd/net.c
> > > > +++ b/cmd/net.c
> > > > @@ -16,6 +16,7 @@
> > > > #include <net.h>
> > > > #include <net/udp.h>
> > > > #include <net/sntp.h>
> > > > +#include <net/ncsi.h>
> > > >
> > > > static int netboot_common(enum proto_t, struct cmd_tbl *, int, char * const []);
> > > >
> > > > @@ -524,3 +525,24 @@ U_BOOT_CMD(
> > > > "list - list available devices\n"
> > > > );
> > > > #endif // CONFIG_DM_ETH
> > > > +
> > > > +#if defined(CONFIG_CMD_NCSI)
> > > > +static int do_ncsi(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[])
> > > > +{
> > > > + if (!phy_interface_is_ncsi() || !ncsi_active()) {
> > > > + printf("Device not configured for NC-SI\n");
> > > > + return CMD_RET_FAILURE;
> > > > + }
> > > > +
> > > > + if (net_loop(NCSI) < 0)
> > > > + return CMD_RET_FAILURE;
> > > > +
> > > > + return CMD_RET_SUCCESS;
> > > > +}
> > > > +
> > > > +U_BOOT_CMD(
> > > > + ncsi, 1, 1, do_ncsi,
> > > > + "Configure attached NIC via NC-SI",
> > > > + ""
> > > > +);
> > > > +#endif /* CONFIG_CMD_NCSI */
> > > > diff --git a/drivers/net/phy/ncsi.c b/drivers/net/phy/ncsi.c
> > > > index bf1e832be9f1..bb7ecebed382 100644
> > > > --- a/drivers/net/phy/ncsi.c
> > > > +++ b/drivers/net/phy/ncsi.c
> > > > @@ -9,6 +9,7 @@
> > > > #include <log.h>
> > > > #include <malloc.h>
> > > > #include <phy.h>
> > > > +#include <net.h>
> > > > #include <net/ncsi.h>
> > > > #include <net/ncsi-pkt.h>
> > > > #include <asm/unaligned.h>
> > > > diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> > > > index 1121b99abff5..d04538838852 100644
> > > > --- a/drivers/net/phy/phy.c
> > > > +++ b/drivers/net/phy/phy.c
> > > > @@ -1026,7 +1026,7 @@ struct phy_device *phy_connect(struct mii_dev *bus, int addr,
> > > > #endif
> > > >
> > > > #ifdef CONFIG_PHY_NCSI
> > > > - if (!phydev)
> > > > + if (!phydev && interface == PHY_INTERFACE_MODE_NCSI)
> > > > phydev = phy_device_create(bus, 0, PHY_NCSI_ID, false);
> > > > #endif
> > > >
> > > > @@ -1101,3 +1101,10 @@ int phy_modify(struct phy_device *phydev, int devad, int regnum, u16 mask,
> > > >
> > > > return phy_write(phydev, devad, regnum, (ret & ~mask) | set);
> > > > }
> > > > +
> > > > +bool phy_interface_is_ncsi(void)
> > > > +{
> > > > + struct eth_pdata *pdata = dev_get_plat(eth_get_dev());
> > > > +
> > > > + return pdata->phy_interface == PHY_INTERFACE_MODE_NCSI;
> > > > +}
> > > > diff --git a/net/net.c b/net/net.c
> > > > index 81905f631592..a4e645ac4425 100644
> > > > --- a/net/net.c
> > > > +++ b/net/net.c
> > > > @@ -93,6 +93,7 @@
> > > > #include <net.h>
> > > > #include <net/fastboot.h>
> > > > #include <net/tftp.h>
> > > > +#include <net/ncsi.h>
> > > > #if defined(CONFIG_CMD_PCAP)
> > > > #include <net/pcap.h>
> > > > #endif
> > > > @@ -410,6 +411,16 @@ int net_loop(enum proto_t protocol)
> > > > net_try_count = 1;
> > > > debug_cond(DEBUG_INT_STATE, "--- net_loop Entry\n");
> > > >
> > > > +#ifdef CONFIG_PHY_NCSI
> > > > + if (phy_interface_is_ncsi() && protocol != NCSI && !ncsi_active()) {
> > > > + printf("%s: configuring NCSI first\n", __func__);
> > > > + if (net_loop(NCSI) < 0)
> > > > + return ret;
> > > > + eth_init_state_only();
> > > > + goto restart;
> > > > + }
> > > > +#endif
> > > > +
> > > > bootstage_mark_name(BOOTSTAGE_ID_ETH_START, "eth_start");
> > > > net_init();
> > > > if (eth_is_on_demand_init()) {
> > > > @@ -423,6 +434,7 @@ int net_loop(enum proto_t protocol)
> > > > } else {
> > > > eth_init_state_only();
> > > > }
> > > > +
> > > > restart:
> > > > #ifdef CONFIG_USB_KEYBOARD
> > > > net_busy_flag = 0;
> > > > @@ -526,6 +538,11 @@ restart:
> > > > case WOL:
> > > > wol_start();
> > > > break;
> > > > +#endif
> > > > +#if defined(CONFIG_PHY_NCSI)
> > > > + case NCSI:
> > > > + ncsi_probe_packages();
> > > > + break;
> > > > #endif
> > > > default:
> > > > break;
> > > > @@ -637,7 +654,7 @@ restart:
> > > > env_set_hex("filesize", net_boot_file_size);
> > > > env_set_hex("fileaddr", image_load_addr);
> > > > }
> > > > - if (protocol != NETCONS)
> > > > + if (protocol != NETCONS && protocol != NCSI)
> > > > eth_halt();
> > > > else
> > > > eth_halt_state_only();
> > > > @@ -1321,6 +1338,11 @@ void net_process_received_packet(uchar *in_packet, int len)
> > > > case PROT_WOL:
> > > > wol_receive(ip, len);
> > > > break;
> > > > +#endif
> > > > +#ifdef CONFIG_PHY_NCSI
> > > > + case PROT_NCSI:
> > > > + ncsi_receive(et, ip, len);
> > > > + break;
> > > > #endif
> > > > }
> > > > }
> > > > @@ -1381,6 +1403,9 @@ common:
> > > >
> > > > #ifdef CONFIG_CMD_RARP
> > > > case RARP:
> > > > +#endif
> > > > +#ifdef CONFIG_PHY_NCSI
> > > > + case NCSI:
> > > > #endif
> > > > case BOOTP:
> > > > case CDP:
> > > > diff --git a/cmd/Kconfig b/cmd/Kconfig
> > > > index ad36ae63c659..bbd00707727d 100644
> > > > --- a/cmd/Kconfig
> > > > +++ b/cmd/Kconfig
> > > > @@ -1796,6 +1796,14 @@ config CMD_LINK_LOCAL
> > > > help
> > > > Acquire a network IP address using the link-local protocol
> > > >
> > > > +config CMD_NCSI
> > > > + bool "ncsi"
> > > > + depends on PHY_NCSI
> > > > + help
> > > > + Manually configure the attached NIC via NC-SI.
> > > > + Normally this happens automatically before other network
> > > > + operations.
> > > > +
> > > > endif
> > > >
> > > > config CMD_ETHSW
> > >
> > Please separate the command from the ncsi generic code.
> > The command interface should be an option that depends on ncsi support.
>
> I don't follow. Do you want them to be separate patches?
Yes. one for the implementation and one for command.
More information about the U-Boot
mailing list