[RFC PATCH 02/17] sunxi: remove CONFIG_MACPWR
Samuel Holland
samuel at sholland.org
Wed Dec 14 10:09:22 CET 2022
Hi Andre,
Thanks for this cleanup! With the two issues below addressed, it looks
good to me.
On 12/5/22 18:45, Andre Przywara wrote:
> The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
> the power for the Ethernet "MAC" (mostly PHY, really).
> In the DT this is described with the phy-supply property in the MAC DT
> node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
> only in U-Boot proper, and use a DM driver there, we should use the DT
> instead of hardcoding this.
>
> Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
> that regulator and enable it, at probe time. Then drop the current code
> from board.c, which was doing that job before.
> This allows us to remove the MACPWR Kconfig definition and the respective
> values from the defconfigs.
... and we don't care about sun7i-gmac here because there's no U-Boot
driver for it, and the Linux driver already uses the devicetree.
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> ---
> arch/arm/mach-sunxi/Kconfig | 7 -------
> board/sunxi/board.c | 10 ----------
> configs/Bananapi_M2_Ultra_defconfig | 1 -
> configs/Bananapi_defconfig | 1 -
> configs/Bananapro_defconfig | 1 -
> configs/Lamobo_R1_defconfig | 1 -
> configs/Mele_A1000_defconfig | 1 -
> configs/Orangepi_defconfig | 1 -
> configs/Orangepi_mini_defconfig | 1 -
> configs/bananapi_m1_plus_defconfig | 1 -
> configs/bananapi_m2_plus_h3_defconfig | 1 -
> configs/bananapi_m2_plus_h5_defconfig | 1 -
> configs/i12-tvbox_defconfig | 1 -
> configs/jesurun_q5_defconfig | 1 -
> configs/mixtile_loftq_defconfig | 1 -
> configs/nanopi_m1_plus_defconfig | 1 -
> configs/nanopi_neo_plus2_defconfig | 1 -
> configs/nanopi_r1s_h5_defconfig | 1 -
> configs/orangepi_pc2_defconfig | 1 -
> configs/orangepi_plus2e_defconfig | 1 -
> configs/orangepi_plus_defconfig | 1 -
> configs/orangepi_win_defconfig | 1 -
> configs/pine_h64_defconfig | 1 -
> configs/zeropi_defconfig | 1 -
> drivers/net/sun8i_emac.c | 9 +++++++--
> drivers/net/sunxi_emac.c | 10 ++++++++--
> 26 files changed, 15 insertions(+), 43 deletions(-)
>
> diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
> index 5f95fe72d08..6220175d612 100644
> --- a/arch/arm/mach-sunxi/Kconfig
> +++ b/arch/arm/mach-sunxi/Kconfig
> @@ -645,13 +645,6 @@ config OLD_SUNXI_KERNEL_COMPAT
> Set this to enable various workarounds for old kernels, this results in
> sub-optimal settings for newer kernels, only enable if needed.
>
> -config MACPWR
> - string "MAC power pin"
> - default ""
> - help
> - Set the pin used to power the MAC. This takes a string in the format
> - understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
> -
> config MMC0_CD_PIN
> string "Card detect pin for mmc0"
> default "PF6" if MACH_SUN8I_A83T || MACH_SUNXI_H3_H5 || MACH_SUN50I
> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
> index ec35a7f06bd..3077cc71ebd 100644
> --- a/board/sunxi/board.c
> +++ b/board/sunxi/board.c
> @@ -228,15 +228,6 @@ int board_init(void)
> if (ret)
> return ret;
>
> - /* strcmp() would look better, but doesn't get optimised away. */
> - if (CONFIG_MACPWR[0]) {
> - macpwr_pin = sunxi_name_to_gpio(CONFIG_MACPWR);
> - if (macpwr_pin >= 0) {
> - gpio_request(macpwr_pin, "macpwr");
> - gpio_direction_output(macpwr_pin, 1);
> - }
> - }
> -
> #if CONFIG_IS_ENABLED(DM_I2C)
> /*
> * Temporary workaround for enabling I2C clocks until proper sunxi DM
> @@ -244,7 +235,6 @@ int board_init(void)
> */
> i2c_init_board();
> #endif
> -
> eth_init_board();
>
> return 0;
> diff --git a/configs/Bananapi_M2_Ultra_defconfig b/configs/Bananapi_M2_Ultra_defconfig
> index 0bd163afdd7..1c4b90ab9d2 100644
> --- a/configs/Bananapi_M2_Ultra_defconfig
> +++ b/configs/Bananapi_M2_Ultra_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-r40-bananapi-m2-ultra"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_R40=y
> CONFIG_DRAM_CLK=576
> -CONFIG_MACPWR="PA17"
This GPIO is actually the PHY reset line, not its power supply. Since
that line has a pull up, I don't think this was necessary to begin with.
> CONFIG_MMC0_CD_PIN="PH13"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_USB1_VBUS_PIN="PH23"
> diff --git a/configs/Bananapi_defconfig b/configs/Bananapi_defconfig
> index 2814d77c187..2a590e141d9 100644
> --- a/configs/Bananapi_defconfig
> +++ b/configs/Bananapi_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_VIDEO_COMPOSITE=y
> CONFIG_GMAC_TX_DELAY=3
> CONFIG_AHCI=y
> diff --git a/configs/Bananapro_defconfig b/configs/Bananapro_defconfig
> index 11375991c81..4b56195d4f2 100644
> --- a/configs/Bananapro_defconfig
> +++ b/configs/Bananapro_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapro"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_USB1_VBUS_PIN="PH0"
> CONFIG_USB2_VBUS_PIN="PH1"
> CONFIG_VIDEO_COMPOSITE=y
> diff --git a/configs/Lamobo_R1_defconfig b/configs/Lamobo_R1_defconfig
> index d51601ff10f..fc63a7fbd46 100644
> --- a/configs/Lamobo_R1_defconfig
> +++ b/configs/Lamobo_R1_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_MMC0_CD_PIN="PH10"
> CONFIG_GMAC_TX_DELAY=4
> CONFIG_AHCI=y
> diff --git a/configs/Mele_A1000_defconfig b/configs/Mele_A1000_defconfig
> index 3424b976772..a407550f6bd 100644
> --- a/configs/Mele_A1000_defconfig
> +++ b/configs/Mele_A1000_defconfig
> @@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y
> CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-a1000"
> CONFIG_SPL=y
> CONFIG_MACH_SUN4I=y
> -CONFIG_MACPWR="PH15"
> CONFIG_VIDEO_VGA=y
> CONFIG_VIDEO_COMPOSITE=y
> CONFIG_AHCI=y
> diff --git a/configs/Orangepi_defconfig b/configs/Orangepi_defconfig
> index b4d5feff309..5c14e327e39 100644
> --- a/configs/Orangepi_defconfig
> +++ b/configs/Orangepi_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_USB1_VBUS_PIN="PH26"
> CONFIG_USB2_VBUS_PIN="PH22"
> CONFIG_VIDEO_VGA=y
> diff --git a/configs/Orangepi_mini_defconfig b/configs/Orangepi_mini_defconfig
> index 43197381114..fdacf0cd123 100644
> --- a/configs/Orangepi_mini_defconfig
> +++ b/configs/Orangepi_mini_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi-mini"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_MMC0_CD_PIN="PH10"
> CONFIG_MMC3_CD_PIN="PH11"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=3
> diff --git a/configs/bananapi_m1_plus_defconfig b/configs/bananapi_m1_plus_defconfig
> index 12ea6a3236a..f398c70ce1a 100644
> --- a/configs/bananapi_m1_plus_defconfig
> +++ b/configs/bananapi_m1_plus_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-m1-plus"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=432
> -CONFIG_MACPWR="PH23"
> CONFIG_VIDEO_COMPOSITE=y
> CONFIG_GMAC_TX_DELAY=3
> CONFIG_AHCI=y
> diff --git a/configs/bananapi_m2_plus_h3_defconfig b/configs/bananapi_m2_plus_h3_defconfig
> index 2bd5a70a2d0..ab138a43060 100644
> --- a/configs/bananapi_m2_plus_h3_defconfig
> +++ b/configs/bananapi_m2_plus_h3_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-bananapi-m2-plus"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_H3=y
> CONFIG_DRAM_CLK=672
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/bananapi_m2_plus_h5_defconfig b/configs/bananapi_m2_plus_h5_defconfig
> index 926cf6f5a4d..29200e53585 100644
> --- a/configs/bananapi_m2_plus_h5_defconfig
> +++ b/configs/bananapi_m2_plus_h5_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-bananapi-m2-plus"
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_CLK=672
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/i12-tvbox_defconfig b/configs/i12-tvbox_defconfig
> index d75a7992a82..11971a8a766 100644
> --- a/configs/i12-tvbox_defconfig
> +++ b/configs/i12-tvbox_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-i12-tvbox"
> CONFIG_SPL=y
> CONFIG_MACH_SUN7I=y
> CONFIG_DRAM_CLK=384
> -CONFIG_MACPWR="PH21"
> CONFIG_VIDEO_COMPOSITE=y
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/jesurun_q5_defconfig b/configs/jesurun_q5_defconfig
> index 2e6b045b549..701d8ecfaa8 100644
> --- a/configs/jesurun_q5_defconfig
> +++ b/configs/jesurun_q5_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-jesurun-q5"
> CONFIG_SPL=y
> CONFIG_MACH_SUN4I=y
> CONFIG_DRAM_CLK=312
> -CONFIG_MACPWR="PH19"
> CONFIG_USB0_VBUS_PIN="PB9"
> CONFIG_VIDEO_COMPOSITE=y
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> diff --git a/configs/mixtile_loftq_defconfig b/configs/mixtile_loftq_defconfig
> index 646594b6e07..cdee80b3566 100644
> --- a/configs/mixtile_loftq_defconfig
> +++ b/configs/mixtile_loftq_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mixtile-loftq"
> CONFIG_SPL=y
> CONFIG_MACH_SUN6I=y
> CONFIG_DRAM_ZQ=251
> -CONFIG_MACPWR="PA21"
This board does not have a regulator in its devicetree.
I verified the rest of the boards have an equivalent GPIO-controlled
fixed regulator in their devicetrees.
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_USB1_VBUS_PIN="PH24"
> CONFIG_USB2_VBUS_PIN=""
> diff --git a/configs/nanopi_m1_plus_defconfig b/configs/nanopi_m1_plus_defconfig
> index 89065f0411a..a3b82de4de6 100644
> --- a/configs/nanopi_m1_plus_defconfig
> +++ b/configs/nanopi_m1_plus_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-m1-plus"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_H3=y
> CONFIG_DRAM_CLK=408
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC0_CD_PIN="PH13"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> diff --git a/configs/nanopi_neo_plus2_defconfig b/configs/nanopi_neo_plus2_defconfig
> index d462b63e944..f7e3efdfe5e 100644
> --- a/configs/nanopi_neo_plus2_defconfig
> +++ b/configs/nanopi_neo_plus2_defconfig
> @@ -6,7 +6,6 @@ CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_CLK=408
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/nanopi_r1s_h5_defconfig b/configs/nanopi_r1s_h5_defconfig
> index 5c332ca5261..760dfe37022 100644
> --- a/configs/nanopi_r1s_h5_defconfig
> +++ b/configs/nanopi_r1s_h5_defconfig
> @@ -6,7 +6,6 @@ CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_CLK=672
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
> index 356ae7ce476..cf75cf4b351 100644
> --- a/configs/orangepi_pc2_defconfig
> +++ b/configs/orangepi_pc2_defconfig
> @@ -5,7 +5,6 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_CLK=672
> CONFIG_DRAM_ZQ=3881977
> -CONFIG_MACPWR="PD6"
> CONFIG_SPL_SPI_SUNXI=y
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/orangepi_plus2e_defconfig b/configs/orangepi_plus2e_defconfig
> index e27b329b0a9..c72adfb3e69 100644
> --- a/configs/orangepi_plus2e_defconfig
> +++ b/configs/orangepi_plus2e_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus2e"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_H3=y
> CONFIG_DRAM_CLK=672
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/orangepi_plus_defconfig b/configs/orangepi_plus_defconfig
> index f4ce4851d7c..c407af38bcc 100644
> --- a/configs/orangepi_plus_defconfig
> +++ b/configs/orangepi_plus_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_H3=y
> CONFIG_DRAM_CLK=672
> -CONFIG_MACPWR="PD6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_USB1_VBUS_PIN="PG13"
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> diff --git a/configs/orangepi_win_defconfig b/configs/orangepi_win_defconfig
> index 1e26970230f..b803dcd01ef 100644
> --- a/configs/orangepi_win_defconfig
> +++ b/configs/orangepi_win_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-orangepi-win"
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I=y
> CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y
> -CONFIG_MACPWR="PD14"
> CONFIG_SPL_SPI_SUNXI=y
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/configs/pine_h64_defconfig b/configs/pine_h64_defconfig
> index 578bd92f6a3..0b482dcea24 100644
> --- a/configs/pine_h64_defconfig
> +++ b/configs/pine_h64_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-pine-h64"
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H6=y
> CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> -CONFIG_MACPWR="PC16"
> CONFIG_MMC0_CD_PIN="PF6"
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_USB3_VBUS_PIN="PL5"
> diff --git a/configs/zeropi_defconfig b/configs/zeropi_defconfig
> index 8365da2c472..7ace1b5cbfd 100644
> --- a/configs/zeropi_defconfig
> +++ b/configs/zeropi_defconfig
> @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-zeropi"
> CONFIG_SPL=y
> CONFIG_MACH_SUN8I_H3=y
> CONFIG_DRAM_CLK=408
> -CONFIG_MACPWR="PD6"
> # CONFIG_VIDEO_DE2 is not set
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SYS_MONITOR_LEN=786432
> diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c
> index 9cca8fa4e0a..c7087b7302d 100644
> --- a/drivers/net/sun8i_emac.c
> +++ b/drivers/net/sun8i_emac.c
> @@ -29,6 +29,7 @@
> #include <net.h>
> #include <reset.h>
> #include <wait_bit.h>
> +#include <power/regulator.h>
>
> #define MDIO_CMD_MII_BUSY BIT(0)
> #define MDIO_CMD_MII_WRITE BIT(1)
> @@ -169,9 +170,8 @@ struct emac_eth_dev {
> struct clk ephy_clk;
> struct reset_ctl tx_rst;
> struct reset_ctl ephy_rst;
> -#if CONFIG_IS_ENABLED(DM_GPIO)
> struct gpio_desc reset_gpio;
> -#endif
> + struct udevice *phy_reg;
> };
>
>
> @@ -738,6 +738,9 @@ static int sun8i_emac_eth_probe(struct udevice *dev)
>
> sun8i_emac_set_syscon(sun8i_pdata, priv);
>
> + if (priv->phy_reg)
> + regulator_set_enable(priv->phy_reg, true);
> +
> sun8i_mdio_init(dev->name, dev);
> priv->bus = miiphy_get_dev_by_name(dev->name);
>
> @@ -844,6 +847,8 @@ static int sun8i_emac_eth_of_to_plat(struct udevice *dev)
> return -EINVAL;
> }
>
> + device_get_supply_regulator(dev, "phy-supply", &priv->phy_reg);
> +
> pdata->phy_interface = -1;
> priv->phyaddr = -1;
> priv->use_internal_phy = false;
> diff --git a/drivers/net/sunxi_emac.c b/drivers/net/sunxi_emac.c
> index 8625e49dae4..ee8b8a1667d 100644
> --- a/drivers/net/sunxi_emac.c
> +++ b/drivers/net/sunxi_emac.c
> @@ -17,6 +17,7 @@
> #include <net.h>
> #include <asm/io.h>
> #include <asm/arch/clock.h>
> +#include <power/regulator.h>
>
> /* EMAC register */
> struct emac_regs {
> @@ -164,9 +165,8 @@ struct emac_eth_dev {
> struct mii_dev *bus;
> struct phy_device *phydev;
> int link_printed;
> -#ifdef CONFIG_DM_ETH
> uchar rx_buf[EMAC_RX_BUFSIZE];
> -#endif
> + struct udevice *phy_reg;
> };
>
> struct emac_rxhdr {
> @@ -575,6 +575,9 @@ static int sunxi_emac_eth_probe(struct udevice *dev)
> if (ret)
> return ret;
>
> + if (priv->phy_reg)
> + regulator_set_enable(priv->phy_reg, true);
> +
> return sunxi_emac_init_phy(priv, dev);
> }
>
> @@ -588,9 +591,12 @@ static const struct eth_ops sunxi_emac_eth_ops = {
> static int sunxi_emac_eth_of_to_plat(struct udevice *dev)
> {
> struct eth_pdata *pdata = dev_get_plat(dev);
> + struct emac_eth_dev *priv = dev_get_priv(dev);
>
> pdata->iobase = dev_read_addr(dev);
>
> + device_get_supply_regulator(dev, "phy-supply", &priv->phy_reg);
For sun4i-emac, the phy-supply property is actually part of the mdio
node, not the emac node.
Regards,
Samuel
> +
> return 0;
> }
>
More information about the U-Boot
mailing list