[PATCH 3/3] net: phy: Add support for ethernet-phy-id with gpio reset
Michal Simek
michal.simek at xilinx.com
Wed Feb 23 15:45:42 CET 2022
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy at xilinx.com>
---
MAINTAINERS | 1 +
drivers/net/phy/Kconfig | 8 ++++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/ethernet_id.c | 69 +++++++++++++++++++++++++++++++++++
drivers/net/phy/phy.c | 5 +++
include/phy.h | 13 +++++++
6 files changed, 97 insertions(+)
create mode 100644 drivers/net/phy/ethernet_id.c
diff --git a/MAINTAINERS b/MAINTAINERS
index c1a5ac95f295..a75f429cb972 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -617,6 +617,7 @@ F: drivers/i2c/muxes/pca954x.c
F: drivers/i2c/zynq_i2c.c
F: drivers/mmc/zynq_sdhci.c
F: drivers/mtd/nand/raw/zynq_nand.c
+F: drivers/net/phy/ethernet_id.c
F: drivers/net/phy/xilinx_phy.c
F: drivers/net/zynq_gem.c
F: drivers/pinctrl/pinctrl-zynqmp.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 4f8d33ce8fd5..74339a25ca53 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -307,6 +307,14 @@ config PHY_XILINX_GMII2RGMII
as bridge between MAC connected over GMII and external phy that
is connected over RGMII interface.
+config PHY_ETHERNET_ID
+ bool "Read ethernet PHY id"
+ depends on DM_GPIO
+ default y if ZYNQ_GEM
+ help
+ Enable this config to read ethernet phy id from the phy node of DT
+ and create a phy device using id.
+
config PHY_FIXED
bool "Fixed-Link PHY"
depends on DM_ETH
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 77f7f606215c..b28440bc4e52 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_PHY_TI_DP83867) += dp83867.o
obj-$(CONFIG_PHY_TI_DP83869) += dp83869.o
obj-$(CONFIG_PHY_XILINX) += xilinx_phy.o
obj-$(CONFIG_PHY_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o
+obj-$(CONFIG_PHY_ETHERNET_ID) += ethernet_id.o
obj-$(CONFIG_PHY_VITESSE) += vitesse.o
obj-$(CONFIG_PHY_MSCC) += mscc.o
obj-$(CONFIG_PHY_FIXED) += fixed.o
diff --git a/drivers/net/phy/ethernet_id.c b/drivers/net/phy/ethernet_id.c
new file mode 100644
index 000000000000..5617ac3ad62f
--- /dev/null
+++ b/drivers/net/phy/ethernet_id.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ethernet phy reset driver
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+
+#include <common.h>
+#include <dm/device_compat.h>
+#include <phy.h>
+#include <linux/delay.h>
+#include <asm/gpio.h>
+
+struct phy_device *phy_connect_phy_id(struct mii_dev *bus, struct udevice *dev,
+ phy_interface_t interface)
+{
+ struct phy_device *phydev;
+ struct ofnode_phandle_args phandle_args;
+ struct gpio_desc gpio;
+ ofnode node;
+ u32 id, assert, deassert;
+ u16 vendor, device;
+ int ret;
+
+ if (dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
+ &phandle_args))
+ return NULL;
+
+ if (!ofnode_valid(phandle_args.node))
+ return NULL;
+
+ node = phandle_args.node;
+
+ ret = ofnode_read_eth_phy_id(node, &vendor, &device);
+ if (ret) {
+ dev_err(dev, "Failed to read eth PHY id, err: %d\n", ret);
+ return NULL;
+ }
+
+ ret = gpio_request_by_name_nodev(node, "reset-gpios", 0, &gpio,
+ GPIOD_ACTIVE_LOW);
+ if (!ret) {
+ assert = ofnode_read_u32_default(node, "reset-assert-us", 0);
+ deassert = ofnode_read_u32_default(node,
+ "reset-deassert-us", 0);
+ ret = dm_gpio_set_value(&gpio, 1);
+ if (ret) {
+ dev_err(dev, "Failed assert gpio, err: %d\n", ret);
+ return NULL;
+ }
+
+ udelay(assert);
+
+ ret = dm_gpio_set_value(&gpio, 0);
+ if (ret) {
+ dev_err(dev, "Failed deassert gpio, err: %d\n", ret);
+ return NULL;
+ }
+
+ udelay(deassert);
+ }
+
+ id = vendor << 16 | device;
+ phydev = phy_device_create(bus, 0, id, false, interface);
+ if (phydev)
+ phydev->node = node;
+
+ return phydev;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index f63705e1b9a1..fffa10f68b3c 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1047,6 +1047,11 @@ struct phy_device *phy_connect(struct mii_dev *bus, int addr,
phydev = phy_device_create(bus, 0, PHY_NCSI_ID, false, interface);
#endif
+#ifdef CONFIG_PHY_ETHERNET_ID
+ if (!phydev)
+ phydev = phy_connect_phy_id(bus, dev, interface);
+#endif
+
#ifdef CONFIG_PHY_XILINX_GMII2RGMII
if (!phydev)
phydev = phy_connect_gmii2rgmii(bus, dev, interface);
diff --git a/include/phy.h b/include/phy.h
index 832d7a169578..9ea4bd42db4d 100644
--- a/include/phy.h
+++ b/include/phy.h
@@ -468,6 +468,19 @@ struct phy_device *phy_device_create(struct mii_dev *bus, int addr,
u32 phy_id, bool is_c45,
phy_interface_t interface);
+/**
+ * phy_connect_phy_id() - Connect to phy device by reading PHY id
+ * from phy node.
+ *
+ * @bus: MII/MDIO bus that hosts the PHY
+ * @dev: Ethernet device to associate to the PHY
+ * @interface: Interface between the MAC and PHY
+ * @return: pointer to phy_device if a PHY is found,
+ * or NULL otherwise
+ */
+struct phy_device *phy_connect_phy_id(struct mii_dev *bus, struct udevice *dev,
+ phy_interface_t interface);
+
static inline ofnode phy_get_ofnode(struct phy_device *phydev)
{
if (ofnode_valid(phydev->node))
--
2.35.1
More information about the U-Boot
mailing list