[PATCH V2] usb: ehci-mx6: Enable OTG detection on imx8mm and imx8mn
Tim Harvey
tharvey at gateworks.com
Tue Jan 4 00:47:48 CET 2022
On Mon, Jan 3, 2022 at 2:32 PM Adam Ford <aford173 at gmail.com> wrote:
>
>
>
> On Mon, Jan 3, 2022 at 10:20 PM Tim Harvey <tharvey at gateworks.com> wrote:
>>
>> On Thu, Dec 23, 2021 at 6:08 AM Adam Ford <aford173 at gmail.com> wrote:
>> >
>> > The imx8mm and imx8mn appear compatible with imx7d-usb
>> > flags in the OTG driver. If the dr_mode is defined as
>> > host or peripheral, the device appears to operate correctly,
>> > however the auto host/peripheral detection results in an error.
>> >
>> > The solution isn't just adding checks for imx8mm and imx8mn to
>> > the check for imx7, because the USB clock needs to be running
>> > to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
>> >
>> > The init_type in both priv and plat data are the same, so it doesn't
>> > make sense to configure the data in the plat data and copy the
>> > data to priv when priv can be configured directly. Instead, rename
>> > ehci_usb_of_to_plat to ehci_usb_dr_mode and call it from the
>> > probe functions after the clocks are enabled, but before the data
>> > is required.
>> >
>> > With that added, the additional checks for imx8mm and imx8mn will
>> > allow reading the register to automatically determine the state
>> > (host or device) of the OTG controller.
>> >
>> > Signed-off-by: Adam Ford <aford173 at gmail.com>
>> > ---
>> > V2: Rename ehci_usb_of_to_plat to ehci_usb_dr_mode and call it
>> > from the probe after the clocks are enabled, but before
>> > the data is needed.
>> >
>> > diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
>> > index 1bd6147c76..f2a34b7f06 100644
>> > --- a/drivers/usb/host/ehci-mx6.c
>> > +++ b/drivers/usb/host/ehci-mx6.c
>> > @@ -513,7 +513,7 @@ static const struct ehci_ops mx6_ehci_ops = {
>> >
>> > static int ehci_usb_phy_mode(struct udevice *dev)
>> > {
>> > - struct usb_plat *plat = dev_get_plat(dev);
>> > + struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
>> > void *__iomem addr = dev_read_addr_ptr(dev);
>> > void *__iomem phy_ctrl, *__iomem phy_status;
>> > const void *blob = gd->fdt_blob;
>> > @@ -540,18 +540,18 @@ static int ehci_usb_phy_mode(struct udevice *dev)
>> > val = readl(phy_ctrl);
>> >
>> > if (val & USBPHY_CTRL_OTG_ID)
>> > - plat->init_type = USB_INIT_DEVICE;
>> > + priv->init_type = USB_INIT_DEVICE;
>> > else
>> > - plat->init_type = USB_INIT_HOST;
>> > - } else if (is_mx7()) {
>> > + priv->init_type = USB_INIT_HOST;
>> > + } else if (is_mx7() || is_imx8mm() || is_imx8mn()) {
>> > phy_status = (void __iomem *)(addr +
>> > USBNC_PHY_STATUS_OFFSET);
>> > val = readl(phy_status);
>> >
>> > if (val & USBNC_PHYSTATUS_ID_DIG)
>> > - plat->init_type = USB_INIT_DEVICE;
>> > + priv->init_type = USB_INIT_DEVICE;
>> > else
>> > - plat->init_type = USB_INIT_HOST;
>> > + priv->init_type = USB_INIT_HOST;
>> > } else {
>> > return -EINVAL;
>> > }
>> > @@ -559,19 +559,19 @@ static int ehci_usb_phy_mode(struct udevice *dev)
>> > return 0;
>> > }
>> >
>> > -static int ehci_usb_of_to_plat(struct udevice *dev)
>> > +static int ehci_usb_dr_mode(struct udevice *dev)
>> > {
>> > - struct usb_plat *plat = dev_get_plat(dev);
>> > + struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
>> > enum usb_dr_mode dr_mode;
>> >
>> > dr_mode = usb_get_dr_mode(dev_ofnode(dev));
>> >
>> > switch (dr_mode) {
>> > case USB_DR_MODE_HOST:
>> > - plat->init_type = USB_INIT_HOST;
>> > + priv->init_type = USB_INIT_HOST;
>> > break;
>> > case USB_DR_MODE_PERIPHERAL:
>> > - plat->init_type = USB_INIT_DEVICE;
>> > + priv->init_type = USB_INIT_DEVICE;
>> > break;
>> > case USB_DR_MODE_OTG:
>> > case USB_DR_MODE_UNKNOWN:
>> > @@ -639,10 +639,8 @@ static int mx6_parse_dt_addrs(struct udevice *dev)
>> >
>> > static int ehci_usb_probe(struct udevice *dev)
>> > {
>> > - struct usb_plat *plat = dev_get_plat(dev);
>> > struct usb_ehci *ehci = dev_read_addr_ptr(dev);
>> > struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
>> > - enum usb_init_type type = plat->init_type;
>> > struct ehci_hccr *hccr;
>> > struct ehci_hcor *hcor;
>> > int ret;
>> > @@ -660,8 +658,6 @@ static int ehci_usb_probe(struct udevice *dev)
>> > return ret;
>> >
>> > priv->ehci = ehci;
>> > - priv->init_type = type;
>> > - priv->phy_type = usb_get_phy_mode(dev_ofnode(dev));
>> >
>> > #if CONFIG_IS_ENABLED(CLK)
>> > ret = clk_get_by_index(dev, 0, &priv->clk);
>> > @@ -677,6 +673,11 @@ static int ehci_usb_probe(struct udevice *dev)
>> > mdelay(1);
>> > #endif
>> >
>> > + ret = ehci_usb_dr_mode(dev);
>> > + if (ret)
>> > + goto err_clk;
>> > + priv->phy_type = usb_get_phy_mode(dev_ofnode(dev));
>> > +
>> > #if CONFIG_IS_ENABLED(DM_REGULATOR)
>> > ret = device_get_supply_regulator(dev, "vbus-supply",
>> > &priv->vbus_supply);
>> > @@ -700,7 +701,7 @@ static int ehci_usb_probe(struct udevice *dev)
>> > #if CONFIG_IS_ENABLED(DM_REGULATOR)
>> > if (priv->vbus_supply) {
>> > ret = regulator_set_enable(priv->vbus_supply,
>> > - (type == USB_INIT_DEVICE) ?
>> > + (priv->init_type == USB_INIT_DEVICE) ?
>> > false : true);
>> > if (ret && ret != -ENOSYS) {
>> > printf("Error enabling VBUS supply (ret=%i)\n", ret);
>> > @@ -785,11 +786,9 @@ U_BOOT_DRIVER(usb_mx6) = {
>> > .name = "ehci_mx6",
>> > .id = UCLASS_USB,
>> > .of_match = mx6_usb_ids,
>> > - .of_to_plat = ehci_usb_of_to_plat,
>> > .probe = ehci_usb_probe,
>> > .remove = ehci_usb_remove,
>> > .ops = &ehci_usb_ops,
>> > - .plat_auto = sizeof(struct usb_plat),
>> > .priv_auto = sizeof(struct ehci_mx6_priv_data),
>> > .flags = DM_FLAG_ALLOC_PRIV_DMA,
>> > };
>> > --
>> > 2.32.0
>> >
>>
>> Adam,
>>
>> How are you testing this for IMX8MM or IMX8MN?
>
>
> I ran "ums 0 mmc 2" to test peripheral mode and verified that I could see the corresponding MMC device appear on my host machine. I actually burned an image to the eMMC and I was able to get Linux to run the eMMC I burned.
>
> I connected a USB host adapter that grounds the ID pin and ran "usb start" to test for mass storage devices, and did simple tests like "fatls usb 0" to verify I could read the thumb drive.
>
> I had to enable power-domain support, USB, mass storage, and a few other items in my config file to get it all to work. I'm traveling, so I won't be able to give you my exact config options that I enabled.
>
Adam,
Thanks - It was the various configs that I was having trouble with...
there are a bunch of dependencies that are not obvious making me think
something else was still missing.
Tested-By: Tim Harvey <tharvey at gateworks.com> on imx8mm-venice-gw73xx-0x
I tested gadget mode via ums as well as host via asix_eth and this was
my defconfig diff for testing:
diff --git a/configs/imx8mm_venice_defconfig b/configs/imx8mm_venice_defconfig
index 822324766843..36a16866f1a0 100644
--- a/configs/imx8mm_venice_defconfig
+++ b/configs/imx8mm_venice_defconfig
@@ -48,6 +48,8 @@ CONFIG_CMD_FUSE=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_UUID=y
@@ -97,6 +99,8 @@ CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_IMX8M=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8M_POWER_DOMAIN=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_BD71837=y
CONFIG_SPL_DM_PMIC_BD71837=y
@@ -112,5 +116,21 @@ CONFIG_SYSRESET_PSCI=y
CONFIG_SYSRESET_WATCHDOG=y
CONFIG_DM_THERMAL=y
CONFIG_IMX_TMU=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_LAN75XX=y
+CONFIG_USB_ETHER_LAN78XX=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_IMX_WATCHDOG=y
CONFIG_HEXDUMP=y
Best Regards,
Tim
More information about the U-Boot
mailing list