[PATCH v8 05/12] doc: update UEFI document for usage of mkeficapsule
AKASHI Takahiro
takahiro.akashi at linaro.org
Fri Jan 7 03:20:45 CET 2022
Heinrich,
Your comments seem inconsistent,
On Sat, Jan 01, 2022 at 11:09:41PM +0100, Heinrich Schuchardt wrote:
> On 12/20/21 06:02, AKASHI Takahiro wrote:
> > Now we can use mkeficapsule command instead of EDK-II's script
> > to create a signed capsule file. So update the instruction for
> > capsule authentication.
> >
> > Signed-off-by: AKASHI Takahiro <takahiro.akashi at linaro.org>
> > Reviewed-by: Simon Glass <sjg at chromium.org>
> > Acked-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
> > ---
> > doc/develop/uefi/uefi.rst | 143 ++++++++++++++++++--------------------
> > 1 file changed, 67 insertions(+), 76 deletions(-)
> >
> > diff --git a/doc/develop/uefi/uefi.rst b/doc/develop/uefi/uefi.rst
> > index f17138f5c765..864d61734bee 100644
> > --- a/doc/develop/uefi/uefi.rst
> > +++ b/doc/develop/uefi/uefi.rst
> > @@ -284,37 +284,52 @@ Support has been added for the UEFI capsule update feature which
> > enables updating the U-Boot image using the UEFI firmware management
> > protocol (FMP). The capsules are not passed to the firmware through
> > the UpdateCapsule runtime service. Instead, capsule-on-disk
> > -functionality is used for fetching the capsule from the EFI System
> > -Partition (ESP) by placing the capsule file under the
> > -\EFI\UpdateCapsule directory.
> > -
> > -The directory \EFI\UpdateCapsule is checked for capsules only within the
> > -EFI system partition on the device specified in the active boot option
> > -determined by reference to BootNext variable or BootOrder variable processing.
> > -The active Boot Variable is the variable with highest priority BootNext or
> > -within BootOrder that refers to a device found to be present. Boot variables
> > -in BootOrder but referring to devices not present are ignored when determining
> > -active boot variable.
> > -Before starting a capsule update make sure your capsules are installed in the
> > -correct ESP partition or set BootNext.
> > +functionality is used for fetching capsules from the EFI System
> > +Partition (ESP) by placing capsule files under the directory::
> > +
> > + \EFI\UpdateCapsule
> > +
> > +The directory is checked for capsules only within the
> > +EFI system partition on the device specified in the active boot option,
> > +which is determined by BootXXXX variable in BootNext, or if not, the highest
> > +priority one within BootOrder. Any BootXXXX variables referring to devices
> > +not present are ignored when determining the active boot option.
> > +
> > +Please note that capsules will be applied in the alphabetic order of
> > +capsule file names.
> > +
> > +Creating a capsule file
> > +***********************
> > +
> > +A capsule file can be created by using tools/mkeficapsule.
> > +To build this tool, enable::
> > +
> > + CONFIG_TOOLS_MKEFICAPSULE=y
> > + CONFIG_TOOLS_LIBCRYPTO=y
> > +
> > +Run the following command::
>
> .. code-block:: bash
OK, but there still exist a number of simple "::" in
doc/develop/uefi/uefi.rst.
> > +
> > + $ mkeficapsule \
>
> %s/$ //
I would like to say nak here.
"$" obviously shows that it is an example of command usage.
This usage can commonly be seen across many docs under doc/ and
even doc/develop/uefi/uefi.rst has some uses.
> > + --index 1 --instance 0 \
> > + [--fit <FIT image> | --raw <raw image>] \
> > + <capsule_file_name>
> >
> > Performing the update
> > *********************
> >
> > -Since U-boot doesn't currently support SetVariable at runtime there's a Kconfig
> > -option (CONFIG_EFI_IGNORE_OSINDICATIONS) to disable the OsIndications variable
> > -check. If that option is enabled just copy your capsule to \EFI\UpdateCapsule.
> > -
> > -If that option is disabled, you'll need to set the OsIndications variable with::
> > +Put capsule files under the directory mentioned above.
> > +Then, following the UEFI specification, you'll need to set
> > +the EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED
> > +bit in OsIndications variable with::
>
> ..code-block::
>
> >
> > => setenv -e -nv -bs -rt -v OsIndications =0x04
>
> %s/=> //
Nak.
"=>" indicates that it is an example of U-Boot command line.
Again, we can see a number of uses across doc/ and even
doc/develop/uefi/uefi.rst has some.
We should not drop the prompt in this kind of citation.
> >
> > -Finally, the capsule update can be initiated either by rebooting the board,
> > -which is the preferred method, or by issuing the following command::
> > +Since U-boot doesn't currently support SetVariable at runtime, its value
> > +won't be taken over across the reboot. If this is the case, you can skip
> > +this feature check with the Kconfig option (CONFIG_EFI_IGNORE_OSINDICATIONS)
> > +set.
> >
> > - => efidebug capsule disk-update
> > -
> > -**The efidebug command is should only be used during debugging/development.**
> > +Finally, the capsule update can be initiated by rebooting the board.
> >
> > Enabling Capsule Authentication
> > *******************************
> > @@ -324,82 +339,58 @@ be updated by verifying the capsule signature. The capsule signature
> > is computed and prepended to the capsule payload at the time of
> > capsule generation. This signature is then verified by using the
> > public key stored as part of the X509 certificate. This certificate is
> > -in the form of an efi signature list (esl) file, which is embedded as
> > -part of U-Boot.
> > +in the form of an efi signature list (esl) file, which is embedded in
> > +a device tree.
> >
> > The capsule authentication feature can be enabled through the
> > following config, in addition to the configs listed above for capsule
> > update::
> >
> > CONFIG_EFI_CAPSULE_AUTHENTICATE=y
> > - CONFIG_EFI_CAPSULE_KEY_PATH=<path to .esl cert>
> >
> > The public and private keys used for the signing process are generated
> > -and used by the steps highlighted below::
> > +and used by the steps highlighted below.
> >
> > - 1. Install utility commands on your host
> > - * OPENSSL
> > +1. Install utility commands on your host
> > + * openssl
> > * efitools
> >
> > - 2. Create signing keys and certificate files on your host
> > +2. Create signing keys and certificate files on your host::
>
> ..code-block:: bash
>
> >
> > $ openssl req -x509 -sha256 -newkey rsa:2048 -subj /CN=CRT/ \
>
> %s/$ //
ditto
> > -keyout CRT.key -out CRT.crt -nodes -days 365
> > $ cert-to-efi-sig-list CRT.crt CRT.esl
> >
> > - $ openssl x509 -in CRT.crt -out CRT.cer -outform DER
> > - $ openssl x509 -inform DER -in CRT.cer -outform PEM -out CRT.pub.pem
> > -
> > - $ openssl pkcs12 -export -out CRT.pfx -inkey CRT.key -in CRT.crt
> > - $ openssl pkcs12 -in CRT.pfx -nodes -out CRT.pem
> > -
> > -The capsule file can be generated by using the GenerateCapsule.py
> > -script in EDKII::
> > -
> > - $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \
> > - <capsule_file_name> --monotonic-count <val> --fw-version \
> > - <val> --lsv <val> --guid \
> > - e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose \
> > - --update-image-index <val> --signer-private-cert \
> > - /path/to/CRT.pem --trusted-public-cert \
> > - /path/to/CRT.pub.pem --other-public-cert /path/to/CRT.pub.pem \
> > - <u-boot.bin>
> > -
> > -Place the capsule generated in the above step on the EFI System
> > -Partition under the EFI/UpdateCapsule directory
> > -
> > -Testing on QEMU
> > -***************
> > +3. Run the following command to create and sign the capsule file::
> >
> > -Currently, support has been added on the QEMU ARM64 virt platform for
> > -updating the U-Boot binary as a raw image when the platform is booted
> > -in non-secure mode, i.e. with CONFIG_TFABOOT disabled. For this
> > -configuration, the QEMU platform needs to be booted with
> > -'secure=off'. The U-Boot binary placed on the first bank of the NOR
> > -flash at offset 0x0. The U-Boot environment is placed on the second
> > -NOR flash bank at offset 0x4000000.
>
> ..code-block:: bash
>
> > + $ mkeficapsule --monotonic-count 1 \
>
> %s/$ //
ditto
-Takahiro Akashi
> Best regards
>
> Heinrich
>
> > + --private-key CRT.key \
> > + --certificate CRT.crt \
> > + --index 1 --instance 0 \
> > + [--fit <FIT image> | --raw <raw image>] \
> > + <capsule_file_name>
> >
> > -The capsule update feature is enabled with the following configuration
> > -settings::
> > +4. Insert the signature list into a device tree in the following format::
> >
> > - CONFIG_MTD=y
> > - CONFIG_FLASH_CFI_MTD=y
> > - CONFIG_CMD_MTDPARTS=y
> > - CONFIG_CMD_DFU=y
> > - CONFIG_DFU_MTD=y
> > - CONFIG_PCI_INIT_R=y
> > - CONFIG_EFI_CAPSULE_ON_DISK=y
> > - CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y
> > - CONFIG_EFI_CAPSULE_FIRMWARE=y
> > - CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y
> > + {
> > + signature {
> > + capsule-key = [ <binary of signature list> ];
> > + }
> > + ...
> > + }
> >
> > -In addition, the following config needs to be disabled(QEMU ARM specific)::
> > + You can do this manually with::
> >
> > - CONFIG_TFABOOT
> > + $ dtc -@ -I dts -O dtb -o signature.dtbo signature.dts
> > + $ fdtoverlay -i orig.dtb -o new.dtb -v signature.dtbo
> >
> > -The capsule file can be generated by using the tools/mkeficapsule::
> > + where signature.dts looks like::
> >
> > - $ mkeficapsule --raw <u-boot.bin> --index 1 <capsule_file_name>
> > + &{/} {
> > + signature {
> > + capsule-key = /incbin/("CRT.esl");
> > + };
> > + };
> >
> > Executing the boot manager
> > ~~~~~~~~~~~~~~~~~~~~~~~~~~
>
More information about the U-Boot
mailing list