[PATCH V2] usb: ehci-mx6: Enable OTG detection on imx8mm and imx8mn

[Adam Ford]

On Tue, Jan 11, 2022 at 9:31 AM Michael Walle <michael at walle.cc> wrote:
>
> Hi,
>
> Am 2022-01-11 15:20, schrieb Adam Ford:
> > On Tue, Jan 4, 2022 at 2:32 AM Michael Walle <michael at walle.cc> wrote:
> >> > The imx8mm and imx8mn appear compatible with imx7d-usb
> >> > flags in the OTG driver.  If the dr_mode is defined as
> >> > host or peripheral, the device appears to operate correctly,
> >> > however the auto host/peripheral detection results in an error.
> >> >
> >> > The solution isn't just adding checks for imx8mm and imx8mn to
> >> > the check for imx7, because the USB clock needs to be running
> >> > to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
> >> >
> >> > The init_type in both priv and plat data are the same, so it doesn't
> >> > make sense to configure the data in the plat data and copy the
> >> > data to priv when priv can be configured directly.  Instead, rename
> >> > ehci_usb_of_to_plat to ehci_usb_dr_mode and call it from the
> >> > probe functions after the clocks are enabled, but before the data
> >> > is required.
> >> >
> >> > With that added, the additional checks for imx8mm and imx8mn will
> >> > allow reading the register to automatically determine the state
> >> > (host or device) of the OTG controller.
> >> >
> >> > Signed-off-by: Adam Ford <aford173 at gmail.com>
> >> > ---
> >> > V2:  Rename ehci_usb_of_to_plat to ehci_usb_dr_mode and call it
> >> >      from the probe after the clocks are enabled, but before
> >> >      the data is needed.
> >> >
> >> > diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
> >> > index 1bd6147c76..f2a34b7f06 100644
> >> > --- a/drivers/usb/host/ehci-mx6.c
> >> > +++ b/drivers/usb/host/ehci-mx6.c
> >>
> >> ..
> >>
> >> > @@ -639,10 +639,8 @@ static int mx6_parse_dt_addrs(struct udevice *dev)
> >> >
> >> >  static int ehci_usb_probe(struct udevice *dev)
> >> >  {
> >> > -     struct usb_plat *plat = dev_get_plat(dev);
> >> >       struct usb_ehci *ehci = dev_read_addr_ptr(dev);
> >> >       struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
> >> > -     enum usb_init_type type = plat->init_type;
> >> >       struct ehci_hccr *hccr;
> >> >       struct ehci_hcor *hcor;
> >> >       int ret;
> >> > @@ -660,8 +658,6 @@ static int ehci_usb_probe(struct udevice *dev)
> >> >               return ret;
> >> >
> >> >       priv->ehci = ehci;
> >> > -     priv->init_type = type;
> >>
> >
> > Michael,
> >
> >> I'm not sure this is correct. There is also this:
> >> https://elixir.bootlin.com/u-boot/v2022.01-rc4/source/drivers/usb/host/usb-uclass.c#L407
> >>
> >
> > Further down in the code, you should see:
> >     priv->phy_type = usb_get_phy_mode(dev_ofnode(dev));
>
> But that is just fetching the mode from the device tree, the
> usb_setup_ehci_gadget() referenced above, change the mode during
> runtime by writing the plat->init_type and reprobing the device.
>
> >> Which won't work anymore. usb_setup_ehci_gadget() is called from
> >> usb_gadget_register_driver() in ci_udc.c. The latter is the one used
> >> on the imx, right? But I might be wrong. I'm still trying to figure
> >> out how this all works together, because I also try to get OTG
> >> running on the dwc3 driver. It looks like the ci_udc.c is special
> >> here, and I wonder how a transition to UCLASS_USB_GADGET_GENERIC
> >> might look like for this driver.
> >
> > This driver really isn't changing anything, it's just an order of
> > operations.
>
> It doesn't use the plat->init_type at all anymore, no?

>From what I could tell, the only thing that plat->init_type did was to
set priv->init_type.
The priv structure appears to do most of the work.

>
> >  Previously there was a separate that was being called to
> > determine the init_type as being either a peripheral or host.  If it
> > wasn't explicitly set in the device tree, the helper function would
> > query a register, however, on the imx8mm and imx8mn platforms, the
> > clocks were not running which resulted in a hang.  What I've done is
> > simply move the helper function into the probe and have it run after
> > the clocks start.  In theory the register values will be the same as
> > they would be with the help function still in place.
> >
> > Both Tim Harvey and I have tested on an imx8mm and Fabio tested it on
> > an imx7.  For me, the peripheral mode worked when the ID pin of the
> > USB-OTG was not grounded.  When it was grounded, the system corrected
> > identified it as a host and I was able to mount a USB drive.
>
> Again, I'm missing something here, but the only user of
> usb_setup_ehci_gadget() is usb/gadget/ci_udc.c.

I can't speak to what those functions do.   What are you suggesting
that I do differently?

adam
>
> -michael