[PATCH 1/3] arm: dts: imx8mn-beacon: Resync dtsi with Kernel 5.17-rc1

[Adam Ford]

Resync the SOM and baseboard files with the device trees that will
be included in 5.17-RC1 when it's cut.  This will improve pinmuxing
for USDHC1 and add USB functionality.  Add edits to
imx8mn-beacon-kit-u-boot for enabling USB.

Signed-off-by: Adam Ford <aford173 at gmail.com>

diff --git a/arch/arm/dts/imx8mn-beacon-baseboard.dtsi b/arch/arm/dts/imx8mn-beacon-baseboard.dtsi
index 376ca8ff72..0f40b43ac0 100644
--- a/arch/arm/dts/imx8mn-beacon-baseboard.dtsi
+++ b/arch/arm/dts/imx8mn-beacon-baseboard.dtsi
@@ -126,7 +126,6 @@
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
-		clock-names = "xclk";
 		DCVDD-supply = <&reg_audio>;
 		DBVDD-supply = <&reg_audio>;
 		AVDD-supply = <&reg_audio>;
diff --git a/arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi b/arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi
index 69fd69c8d0..a06b271787 100644
--- a/arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi
+++ b/arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi
@@ -110,6 +110,10 @@
 	u-boot,dm-spl;
 };
 
+&usbotg1 {
+	dr_mode="host";
+};
+
 &usdhc1 {
 	u-boot,dm-spl;
 	sd-uhs-sdr104;
diff --git a/arch/arm/dts/imx8mn-beacon-som.dtsi b/arch/arm/dts/imx8mn-beacon-som.dtsi
index de2cd0e320..1133cded9b 100644
--- a/arch/arm/dts/imx8mn-beacon-som.dtsi
+++ b/arch/arm/dts/imx8mn-beacon-som.dtsi
@@ -101,7 +101,7 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
@@ -120,6 +120,9 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
 
 		regulators {
 			buck1_reg: BUCK1 {
@@ -262,12 +265,15 @@
 &usdhc1 {
 	#address-cells = <1>;
 	#size-cells = <0>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&buck4_reg>;
+	vqmmc-supply = <&buck5_reg>;
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&usdhc1_pwrseq>;
 	status = "okay";
-- 
2.32.0