[PATCH v5 3/3] arm: kirkwood: Pogoplug-V4 : Add board implementation files
Tony Dinh
mibodhi at gmail.com
Tue Jan 25 02:06:11 CET 2022
Hi Stefan,
On Mon, Jan 24, 2022 at 2:25 AM Tony Dinh <mibodhi at gmail.com> wrote:
>
> Hi Stefan,
>
> On Mon, Jan 24, 2022 at 1:41 AM Stefan Roese <sr at denx.de> wrote:
> >
> > On 1/24/22 07:17, Tony Dinh wrote:
> > > Add board header, defconfig, and implementation files for Pogoplug V4.
> > >
> > > Signed-off-by: Tony Dinh <mibodhi at gmail.com>
> > > ---
> > >
> > > Changes in v5:
> > > - Currently, CONFIG_RESET_PHY_R symbol is used in
> > > arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
> > > boards with mv8831116 PHY, with each board defines the function
> > > reset_phy(). Undefine it for this board.
> > > - Add board_eth_init() to use uclass mvgbe to handle all Ethernet
> > > PHY configuration and bring up the network.
> >
> > Okay, good. I'm a bit puzzled that you don't need (want) to enable the
> > Marvell ethernet PHY driver for this as well. But perhaps this is an
> > optimization for some follow-up patches - also for some other Kirkwood
> > boards.
>
> Exactly! For Kirkwood boards with MV88E1116 PHY (about 6 boards), it
> is enough to let the uclass mvgbe handle all the PHY config and bring
> up the Gbits network using the PHY default genphy_config(). And it
> will run in gmii phy-mode.
>
> The optimization will come in a follow-up patch, where we will enable
> rgmii phy-mode in the DTS. I'll submit a follow-up patch in which
> we'll use u-boot.dtsi to add phy-mode="rgmii". And then I'll follow up
> with patches for other Kirkwood boards to use the same approach.
>
Follow up on my thinking above about using the DTS to optimize. I was
wrong, the DTS just does not have enough to do what I thought we
could. So I'll send a follow up patch using the Marvell driver config
for this.
Thanks,
Tony
> >
> > So for now:
> >
> > Reviewed-by: Stefan Roese <sr at denx.de>
> >
> > Thanks,
> > Stefan
> >
> >
> > > Changes in v4:
> > > - Remove CONFIG_FEATURE_COMMAND_EDITING and ifdefs for CMD_NET
> > > in include header
> > >
> > > Changes in v3:
> > > - Squash board file small patches into one patch
> > > - Migrate config symbols from board include header to defconfig
> > > - Remove obsolete config symbols from header file
> > > - Don't use ifdefs for unselectable config symbols in header file
> > >
> > > Changes in v2:
> > > - Move constants to .c file and remove header file
> > > - Use canonical format for defconfig file
> > >
> > > board/cloudengines/pogo_v4/MAINTAINERS | 6 +
> > > board/cloudengines/pogo_v4/Makefile | 10 ++
> > > board/cloudengines/pogo_v4/kwbimage.cfg | 148 ++++++++++++++++++++++++
> > > board/cloudengines/pogo_v4/pogo_v4.c | 148 ++++++++++++++++++++++++
> > > configs/pogo_v4_defconfig | 79 +++++++++++++
> > > include/configs/pogo_v4.h | 56 +++++++++
> > > 6 files changed, 447 insertions(+)
> > > create mode 100644 board/cloudengines/pogo_v4/MAINTAINERS
> > > create mode 100644 board/cloudengines/pogo_v4/Makefile
> > > create mode 100644 board/cloudengines/pogo_v4/kwbimage.cfg
> > > create mode 100644 board/cloudengines/pogo_v4/pogo_v4.c
> > > create mode 100644 configs/pogo_v4_defconfig
> > > create mode 100644 include/configs/pogo_v4.h
> > >
> > > diff --git a/board/cloudengines/pogo_v4/MAINTAINERS b/board/cloudengines/pogo_v4/MAINTAINERS
> > > new file mode 100644
> > > index 0000000000..35fd7858b7
> > > --- /dev/null
> > > +++ b/board/cloudengines/pogo_v4/MAINTAINERS
> > > @@ -0,0 +1,6 @@
> > > +POGO_V4 BOARD
> > > +M: Tony Dinh <mibodhi at gmail.com>
> > > +S: Maintained
> > > +F: board/cloudengines/pogo_v4/
> > > +F: include/configs/pogo_v4.h
> > > +F: configs/pogo_v4_defconfig
> > > diff --git a/board/cloudengines/pogo_v4/Makefile b/board/cloudengines/pogo_v4/Makefile
> > > new file mode 100644
> > > index 0000000000..511bf5ff7e
> > > --- /dev/null
> > > +++ b/board/cloudengines/pogo_v4/Makefile
> > > @@ -0,0 +1,10 @@
> > > +# SPDX-License-Identifier: GPL-2.0+
> > > +#
> > > +# (C) Copyright 2014-2021 Tony Dinh <mibodhi at gmail.com>
> > > +#
> > > +# Based on
> > > +# Marvell Semiconductor <www.marvell.com>
> > > +# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> > > +#
> > > +
> > > +obj-y := pogo_v4.o
> > > diff --git a/board/cloudengines/pogo_v4/kwbimage.cfg b/board/cloudengines/pogo_v4/kwbimage.cfg
> > > new file mode 100644
> > > index 0000000000..f6294fe313
> > > --- /dev/null
> > > +++ b/board/cloudengines/pogo_v4/kwbimage.cfg
> > > @@ -0,0 +1,148 @@
> > > +# SPDX-License-Identifier: GPL-2.0+
> > > +#
> > > +# Copyright (C) 2012
> > > +# David Purdy <david.c.purdy at gmail.com>
> > > +#
> > > +# Based on Kirkwood support:
> > > +# (C) Copyright 2009
> > > +# Marvell Semiconductor <www.marvell.com>
> > > +# Written-by: Prafulla Wadaskar <prafulla <at> marvell.com>
> > > +
> > > +# Boot Media configurations (DONE)
> > > +BOOT_FROM nand
> > > +NAND_ECC_MODE default
> > > +NAND_PAGE_SIZE 0x0800
> > > +
> > > +# SOC registers configuration using bootrom header extension
> > > +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> > > +
> > > +# Configure RGMII-0 interface pad voltage to 1.8V (SHOULD BE SAME)
> > > +DATA 0xffd100e0 0x1b1b1b9b
> > > +
> > > +#Dram initalization for SINGLE x16 CL=3 @ 200MHz (need CL=3 @ 200MHz?)
> > > +DATA 0xffd01400 0x43000618 # DDR Configuration register
> > > +# bit13-0: 0x200 (200 DDR2 clks refresh rate)
> > > +# bit23-14: zero
> > > +# bit24: 1= enable exit self refresh mode on DDR access
> > > +# bit25: 1 required
> > > +# bit29-26: zero
> > > +# bit31-30: 01
> > > +
> > > +DATA 0xffd01404 0x34143000 # DDR Controller Control Low
> > > +# bit 4: 0=addr/cmd in smame cycle
> > > +# bit 5: 0=clk is driven during self refresh, we don't care for APX
> > > +# bit 6: 0=use recommended falling edge of clk for addr/cmd
> > > +# bit14: 0=input buffer always powered up
> > > +# bit18: 1=cpu lock transaction enabled
> > > +# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0
> > > +# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> > > +# bit30-28: 3 required
> > > +# bit31: 0=no additional STARTBURST delay
> > > +
> > > +DATA 0xffd01408 0x11012227 # DDR Timing (Low) (active cycles value +1)
> > > +# bit3-0: TRAS lsbs
> > > +# bit7-4: TRCD
> > > +# bit11- 8: TRP
> > > +# bit15-12: TWR
> > > +# bit19-16: TWTR
> > > +# bit20: TRAS msb
> > > +# bit23-21: 0x0
> > > +# bit27-24: TRRD
> > > +# bit31-28: TRTP
> > > +
> > > +DATA 0xffd0140c 0x00000819 # DDR Timing (High)
> > > +# bit6-0: TRFC
> > > +# bit8-7: TR2R
> > > +# bit10-9: TR2W
> > > +# bit12-11: TW2W
> > > +# bit31-13: zero required
> > > +
> > > +DATA 0xffd01410 0x00000001 # DDR Address Control (changed to Dockstar vals)
> > > +# bit1-0: 00, Cs0width=x16
> > > +# bit3-2: 10, Cs0size=512Mb
> > > +# bit5-4: 00, Cs2width=nonexistent
> > > +# bit7-6: 00, Cs1size =nonexistent
> > > +# bit9-8: 00, Cs2width=nonexistent
> > > +# bit11-10: 00, Cs2size =nonexistent
> > > +# bit13-12: 00, Cs3width=nonexistent
> > > +# bit15-14: 00, Cs3size =nonexistent
> > > +# bit16: 0, Cs0AddrSel
> > > +# bit17: 0, Cs1AddrSel
> > > +# bit18: 0, Cs2AddrSel
> > > +# bit19: 0, Cs3AddrSel
> > > +# bit31-20: 0 required
> > > +
> > > +DATA 0xffd01414 0x00000000 # DDR Open Pages Control
> > > +# bit0: 0, OpenPage enabled
> > > +# bit31-1: 0 required
> > > +
> > > +DATA 0xffd01418 0x00000000 # DDR Operation
> > > +# bit3-0: 0x0, DDR cmd
> > > +# bit31-4: 0 required
> > > +
> > > +DATA 0xffd0141c 0x00000632 # DDR Mode
> > > +# bit2-0: 2, BurstLen=2 required
> > > +# bit3: 0, BurstType=0 required
> > > +# bit6-4: 4, CL=5 (<===== change to CL=3 ?)
> > > +# bit7: 0, TestMode=0 normal
> > > +# bit8: 0, DLL reset=0 normal
> > > +# bit11-9: 6, auto-precharge write recovery ????????????
> > > +# bit12: 0, PD must be zero
> > > +# bit31-13: 0 required
> > > +
> > > +DATA 0xffd01420 0x00000040 # DDR Extended Mode
> > > +# bit0: 0, DDR DLL enabled
> > > +# bit1: 0, DDR drive strenght normal
> > > +# bit2: 0, DDR ODT control lsd (disabled)
> > > +# bit5-3: 000, required
> > > +# bit6: 1, DDR ODT control msb, (disabled)
> > > +# bit9-7: 000, required
> > > +# bit10: 0, differential DQS enabled
> > > +# bit11: 0, required
> > > +# bit12: 0, DDR output buffer enabled
> > > +# bit31-13: 0 required
> > > +
> > > +DATA 0xffd01424 0x0000F07F # DDR Controller Control High
> > > +# bit2-0: 111, required
> > > +# bit3 : 1 , MBUS Burst Chop disabled
> > > +# bit6-4: 111, required
> > > +# bit7 : 0
> > > +# bit8 : 0 , no sample stage
> > > +# bit9 : 0 , no half clock cycle addition to dataout
> > > +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> > > +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> > > +# bit15-12: 1111 required
> > > +# bit31-16: 0 required
> > > +
> > > +DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
> > > +DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
> > > +
> > > +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> > > +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
> > > +# bit0: 1, Window enabled
> > > +# bit1: 0, Write Protect disabled
> > > +# bit3-2: 00, CS0 hit selected
> > > +# bit23-4: ones, required
> > > +# bit31-24: 0x07, Size (i.e. 128MB)
> > > +
> > > +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> > > +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> > > +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> > > +
> > > +DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) (DONE)
> > > +# bit3-0: 2, ODT0Rd, MODT[0] asserted during read from DRAM CS1
> > > +# bit7-4: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> > > +# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
> > > +# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> > > +
> > > +DATA 0xffd01498 0x00000000 # DDR ODT Control (High) (DONE)
> > > +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> > > +# bit3-2: 01, ODT1 active NEVER!
> > > +# bit31-4: zero, required
> > > +
> > > +DATA 0xffd0149c 0x0000e803 # CPU ODT Control (DONE)
> > > +DATA 0xffd01480 0x00000001 # DDR Initialization Control (DONE)
> > > +#bit0=1, enable DDR init upon this register write
> > > +
> > > +# End of Header extension
> > > +DATA 0x0 0x0
> > > diff --git a/board/cloudengines/pogo_v4/pogo_v4.c b/board/cloudengines/pogo_v4/pogo_v4.c
> > > new file mode 100644
> > > index 0000000000..61ce0d59c7
> > > --- /dev/null
> > > +++ b/board/cloudengines/pogo_v4/pogo_v4.c
> > > @@ -0,0 +1,148 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright (C) 2014-2022 Tony Dinh <mibodhi at gmail.com>
> > > + *
> > > + * Based on
> > > + * Copyright (C) 2012 David Purdy <david.c.purdy at gmail.com>
> > > + *
> > > + * Based on Kirkwood support:
> > > + * (C) Copyright 2009
> > > + * Marvell Semiconductor <www.marvell.com>
> > > + * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> > > + */
> > > +
> > > +#include <common.h>
> > > +#include <netdev.h>
> > > +#include <asm/arch/cpu.h>
> > > +#include <asm/arch/soc.h>
> > > +#include <asm/arch/mpp.h>
> > > +#include <asm/io.h>
> > > +#include <asm/arch/gpio.h>
> > > +#include <asm/mach-types.h>
> > > +#include <bootstage.h>
> > > +#include <command.h>
> > > +#include <init.h>
> > > +#include <linux/bitops.h>
> > > +
> > > +DECLARE_GLOBAL_DATA_PTR;
> > > +
> > > +/* GPIO configuration */
> > > +#define POGO_V4_OE_LOW (~(0))
> > > +#define POGO_V4_OE_HIGH (~(0))
> > > +#define POGO_V4_OE_VAL_LOW BIT(29)
> > > +#define POGO_V4_OE_VAL_HIGH 0
> > > +
> > > +/* button */
> > > +#define BTN_EJECT 29
> > > +
> > > +int board_early_init_f(void)
> > > +{
> > > + /*
> > > + * default gpio configuration
> > > + * There are maximum 64 gpios controlled through 2 sets of registers
> > > + * the below configuration configures mainly initial LED status
> > > + */
> > > + mvebu_config_gpio(POGO_V4_OE_VAL_LOW,
> > > + POGO_V4_OE_VAL_HIGH,
> > > + POGO_V4_OE_LOW, POGO_V4_OE_HIGH);
> > > +
> > > + /* Multi-Purpose Pins Functionality configuration */
> > > + u32 kwmpp_config[] = {
> > > + MPP0_NF_IO2,
> > > + MPP1_NF_IO3,
> > > + MPP2_NF_IO4,
> > > + MPP3_NF_IO5,
> > > + MPP4_NF_IO6,
> > > + MPP5_NF_IO7,
> > > + MPP6_SYSRST_OUTn,
> > > + MPP7_GPO,
> > > + MPP8_TW_SDA,
> > > + MPP9_TW_SCK,
> > > + MPP10_UART0_TXD,
> > > + MPP11_UART0_RXD,
> > > + MPP12_SD_CLK,
> > > + MPP13_SD_CMD,
> > > + MPP14_SD_D0,
> > > + MPP15_SD_D1,
> > > + MPP16_SD_D2,
> > > + MPP17_SD_D3,
> > > + MPP18_NF_IO0,
> > > + MPP19_NF_IO1,
> > > + MPP20_SATA1_ACTn,
> > > + MPP21_SATA0_ACTn,
> > > + MPP22_GPIO, /* Green LED */
> > > + MPP23_GPIO,
> > > + MPP24_GPIO, /* Red LED */
> > > + MPP25_GPIO,
> > > + MPP26_GPIO,
> > > + MPP27_GPIO,
> > > + MPP28_GPIO,
> > > + MPP29_GPIO, /* Eject button */
> > > + MPP30_GPIO,
> > > + MPP31_GPIO,
> > > + MPP32_GPIO,
> > > + MPP33_GPIO,
> > > + MPP34_GPIO,
> > > + MPP35_GPIO, /* FR6192 has only 36 GPIOs */
> > > + 0
> > > + };
> > > + kirkwood_mpp_conf(kwmpp_config, NULL);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +int board_eth_init(struct bd_info *bis)
> > > +{
> > > + return cpu_eth_init(bis);
> > > +}
> > > +
> > > +int board_late_init(void)
> > > +{
> > > + /* Do late init to ensure successful enumeration of XHCI devices */
> > > + pci_init();
> > > + return 0;
> > > +}
> > > +
> > > +int board_init(void)
> > > +{
> > > + /* Boot parameters address */
> > > + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +#if CONFIG_IS_ENABLED(BOOTSTAGE)
> > > +#define GREEN_LED BIT(22)
> > > +#define RED_LED BIT(24)
> > > +#define BOTH_LEDS (GREEN_LED | RED_LED)
> > > +#define NEITHER_LED 0
> > > +
> > > +static void set_leds(u32 leds, u32 blinking)
> > > +{
> > > + struct kwgpio_registers *r;
> > > + u32 oe;
> > > + u32 bl;
> > > +
> > > + r = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
> > > + oe = readl(&r->oe) | BOTH_LEDS;
> > > + writel(oe & ~leds, &r->oe); /* active low */
> > > + bl = readl(&r->blink_en) & ~BOTH_LEDS;
> > > + writel(bl | blinking, &r->blink_en);
> > > +}
> > > +
> > > +void show_boot_progress(int val)
> > > +{
> > > + switch (val) {
> > > + case BOOTSTAGE_ID_RUN_OS: /* booting Linux */
> > > + set_leds(BOTH_LEDS, NEITHER_LED);
> > > + break;
> > > + case BOOTSTAGE_ID_NET_ETH_START: /* Ethernet initialization */
> > > + set_leds(GREEN_LED, GREEN_LED);
> > > + break;
> > > + default:
> > > + if (val < 0) /* error */
> > > + set_leds(RED_LED, RED_LED);
> > > + break;
> > > + }
> > > +}
> > > +#endif
> > > diff --git a/configs/pogo_v4_defconfig b/configs/pogo_v4_defconfig
> > > new file mode 100644
> > > index 0000000000..5490067b9e
> > > --- /dev/null
> > > +++ b/configs/pogo_v4_defconfig
> > > @@ -0,0 +1,79 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_SKIP_LOWLEVEL_INIT=y
> > > +CONFIG_SYS_DCACHE_OFF=y
> > > +CONFIG_ARCH_CPU_INIT=y
> > > +CONFIG_SYS_THUMB_BUILD=y
> > > +CONFIG_ARCH_KIRKWOOD=y
> > > +CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_v4/kwbimage.cfg"
> > > +CONFIG_SYS_TEXT_BASE=0x600000
> > > +CONFIG_TARGET_POGO_V4=y
> > > +CONFIG_ENV_SIZE=0x20000
> > > +CONFIG_ENV_OFFSET=0xC0000
> > > +CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogoplug-series-4"
> > > +CONFIG_IDENT_STRING="\nPogoplug V4"
> > > +CONFIG_SYS_LOAD_ADDR=0x800000
> > > +CONFIG_BOOTSTAGE=y
> > > +CONFIG_SHOW_BOOT_PROGRESS=y
> > > +CONFIG_BOOTDELAY=10
> > > +CONFIG_USE_BOOTCOMMAND=y
> > > +CONFIG_BOOTCOMMAND="setenv bootargs ${bootargs_console}; run bootcmd_usb; bootm 0x00800000 0x01100000 0x2c00000"
> > > +CONFIG_USE_PREBOOT=y
> > > +CONFIG_BOARD_LATE_INIT=y
> > > +CONFIG_HUSH_PARSER=y
> > > +CONFIG_SYS_PROMPT="Pogo_V4> "
> > > +CONFIG_CMD_BOOTZ=y
> > > +# CONFIG_BOOTM_PLAN9 is not set
> > > +# CONFIG_BOOTM_RTEMS is not set
> > > +# CONFIG_BOOTM_VXWORKS is not set
> > > +# CONFIG_CMD_FLASH is not set
> > > +CONFIG_CMD_MMC=y
> > > +CONFIG_CMD_MTD=y
> > > +CONFIG_CMD_NAND=y
> > > +CONFIG_CMD_PCI=y
> > > +CONFIG_CMD_SATA=y
> > > +CONFIG_CMD_USB=y
> > > +CONFIG_CMD_DHCP=y
> > > +CONFIG_CMD_MII=y
> > > +CONFIG_CMD_PING=y
> > > +CONFIG_CMD_SNTP=y
> > > +CONFIG_CMD_DNS=y
> > > +CONFIG_CMD_EXT2=y
> > > +CONFIG_CMD_EXT4=y
> > > +CONFIG_CMD_FAT=y
> > > +CONFIG_CMD_FS_GENERIC=y
> > > +CONFIG_CMD_JFFS2=y
> > > +CONFIG_CMD_MTDPARTS=y
> > > +CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
> > > +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)"
> > > +CONFIG_CMD_UBI=y
> > > +CONFIG_ISO_PARTITION=y
> > > +CONFIG_EFI_PARTITION=y
> > > +CONFIG_PARTITION_TYPE_GUID=y
> > > +CONFIG_OF_CONTROL=y
> > > +CONFIG_ENV_OVERWRITE=y
> > > +CONFIG_ENV_IS_IN_NAND=y
> > > +CONFIG_VERSION_VARIABLE=y
> > > +CONFIG_NET_RANDOM_ETHADDR=y
> > > +CONFIG_NETCONSOLE=y
> > > +CONFIG_DM=y
> > > +CONFIG_SATA_MV=y
> > > +CONFIG_KIRKWOOD_GPIO=y
> > > +# CONFIG_MMC_HW_PARTITIONING is not set
> > > +CONFIG_MVEBU_MMC=y
> > > +CONFIG_MTD=y
> > > +CONFIG_MTD_RAW_NAND=y
> > > +CONFIG_DM_ETH=y
> > > +CONFIG_MVGBE=y
> > > +CONFIG_MII=y
> > > +CONFIG_PCI=y
> > > +CONFIG_PCI_MVEBU=y
> > > +CONFIG_DM_RTC=y
> > > +CONFIG_RTC_EMULATION=y
> > > +CONFIG_SYS_NS16550=y
> > > +CONFIG_USB=y
> > > +CONFIG_USB_XHCI_HCD=y
> > > +CONFIG_USB_XHCI_PCI=y
> > > +CONFIG_USB_EHCI_HCD=y
> > > +CONFIG_USB_STORAGE=y
> > > +CONFIG_JFFS2_LZO=y
> > > +CONFIG_JFFS2_NAND=y
> > > diff --git a/include/configs/pogo_v4.h b/include/configs/pogo_v4.h
> > > new file mode 100644
> > > index 0000000000..568a93623d
> > > --- /dev/null
> > > +++ b/include/configs/pogo_v4.h
> > > @@ -0,0 +1,56 @@
> > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > +/*
> > > + * Copyright (C) 2014-2022 Tony Dinh <mibodhi at gmail.com>
> > > + *
> > > + * Based on
> > > + * Copyright (C) 2012
> > > + * David Purdy <david.c.purdy at gmail.com>
> > > + *
> > > + * Based on Kirkwood support:
> > > + * (C) Copyright 2009
> > > + * Marvell Semiconductor <www.marvell.com>
> > > + * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> > > + */
> > > +
> > > +#ifndef _CONFIG_POGO_V4_H
> > > +#define _CONFIG_POGO_V4_H
> > > +
> > > +/*
> > > + * mv-common.h should be defined after CMD configs since it used them
> > > + * to enable certain macros
> > > + */
> > > +#include "mv-common.h"
> > > +
> > > +/*
> > > + * Default environment variables
> > > + */
> > > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > > + "dtb_file=/boot/dts/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
> > > + "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"\
> > > + "mtdids=nand0=orion_nand\0"\
> > > + "bootargs_console=console=ttyS0,115200\0" \
> > > + "bootcmd_usb=usb start; load usb 0:1 0x00800000 /boot/uImage; " \
> > > + "load usb 0:1 0x01100000 /boot/uInitrd; " \
> > > + "load usb 0:1 0x2c00000 $dtb_file\0"
> > > +
> > > +/*
> > > + * Ethernet Driver configuration
> > > + */
> > > +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
> > > +#define CONFIG_PHY_BASE_ADR 0
> > > +#ifdef CONFIG_RESET_PHY_R
> > > +#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */
> > > +#endif
> > > +
> > > +/*
> > > + * SATA Driver configuration
> > > + */
> > > +#define CONFIG_SYS_SATA_MAX_DEVICE 1
> > > +
> > > +/*
> > > + * Support large disk for SATA and USB
> > > + */
> > > +#define CONFIG_SYS_64BIT_LBA
> > > +#define CONFIG_LBA48
> > > +
> > > +#endif /* _CONFIG_POGO_V4_H */
> > >
> >
> > Viele Grüße,
> > Stefan Roese
> >
> > --
> > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list