[PATCH 1/5] sunxi: move non-essential code out of s_init()

Andre Przywara andre.przywara at arm.com
Tue Jan 25 02:15:13 CET 2022


So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.

Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.

This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.

Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 arch/arm/mach-sunxi/board.c | 27 ++++++++++++++-------------
 1 file changed, 14 insertions(+), 13 deletions(-)

diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index 3ef179742c5..390c9f8850d 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -75,6 +75,7 @@ ulong board_get_usable_ram_top(ulong total_size)
 }
 #endif
 
+#ifdef CONFIG_SPL_BUILD
 static int gpio_init(void)
 {
 	__maybe_unused uint val;
@@ -172,7 +173,6 @@ static int gpio_init(void)
 	return 0;
 }
 
-#if defined(CONFIG_SPL_BOARD_LOAD_IMAGE) && defined(CONFIG_SPL_BUILD)
 static int spl_board_load_image(struct spl_image_info *spl_image,
 				struct spl_boot_device *bootdev)
 {
@@ -227,18 +227,6 @@ void s_init(void)
 		"mcr p15, 0, r0, c1, c0, 1\n"
 		::: "r0");
 #endif
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_H3
-	/* Enable non-secure access to some peripherals */
-	tzpc_init();
-#endif
-
-	clock_init();
-	timer_init();
-	gpio_init();
-#if !CONFIG_IS_ENABLED(DM_I2C)
-	i2c_init_board();
-#endif
-	eth_init_board();
 }
 
 #define SUNXI_INVALID_BOOT_SOURCE	-1
@@ -335,6 +323,19 @@ u32 spl_boot_device(void)
 
 void board_init_f(ulong dummy)
 {
+#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_H3
+	/* Enable non-secure access to some peripherals */
+	tzpc_init();
+#endif
+
+	clock_init();
+	timer_init();
+	gpio_init();
+#if !CONFIG_IS_ENABLED(DM_I2C)
+	i2c_init_board();
+#endif
+	eth_init_board();
+
 	spl_init();
 	preloader_console_init();
 
-- 
2.17.6



More information about the U-Boot mailing list