[PATCH v3 2/3] net/ftgmac100: Add NC-SI mode support

Cédric Le Goater clg at kaod.org
Mon Jul 4 10:20:15 CEST 2022


On 7/4/22 09:58, Joel Stanley wrote:
> From: Samuel Mendoza-Jonas <sam at mendozajonas.com>
> 
> Update the ftgmac100 driver to support NC-SI instead of an mdio phy
> where available. This is a common setup for Aspeed AST2x00 platforms.
> 
> NC-SI mode is determined from the device-tree if either phy-mode sets it
> or the use-ncsi property exists. If set then normal mdio setup is
> skipped in favour of the NC-SI phy.
> 
> Signed-off-by: Samuel Mendoza-Jonas <sam at mendozajonas.com>
> Signed-off-by: Joel Stanley <joel at jms.id.au>

Reviewed-by: Cédric Le Goater <clg at kaod.org>

Thanks,

C.


> ---
> v3:
>   - Simplify ncsi enable by re-using pdata->phy_interface parsing.
>     use-ncsi still overrides this value.
>   - Fix up freeing in remove callback per Joe's review
> 
>   drivers/net/ftgmac100.c | 14 ++++++++++----
>   1 file changed, 10 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/net/ftgmac100.c b/drivers/net/ftgmac100.c
> index 78779d7d60b9..69370ea5cca2 100644
> --- a/drivers/net/ftgmac100.c
> +++ b/drivers/net/ftgmac100.c
> @@ -188,7 +188,7 @@ static int ftgmac100_phy_adjust_link(struct ftgmac100_data *priv)
>   	struct phy_device *phydev = priv->phydev;
>   	u32 maccr;
>   
> -	if (!phydev->link) {
> +	if (!phydev->link && priv->phy_mode != PHY_INTERFACE_MODE_NCSI) {
>   		dev_err(phydev->dev, "No link\n");
>   		return -EREMOTEIO;
>   	}
> @@ -228,7 +228,8 @@ static int ftgmac100_phy_init(struct udevice *dev)
>   	if (!phydev)
>   		return -ENODEV;
>   
> -	phydev->supported &= PHY_GBIT_FEATURES;
> +	if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI)
> +		phydev->supported &= PHY_GBIT_FEATURES;
>   	if (priv->max_speed) {
>   		ret = phy_set_supported(phydev, priv->max_speed);
>   		if (ret)
> @@ -308,7 +309,8 @@ static void ftgmac100_stop(struct udevice *dev)
>   
>   	writel(0, &ftgmac100->maccr);
>   
> -	phy_shutdown(priv->phydev);
> +	if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI)
> +		phy_shutdown(priv->phydev);
>   }
>   
>   static int ftgmac100_start(struct udevice *dev)
> @@ -580,6 +582,9 @@ static int ftgmac100_probe(struct udevice *dev)
>   	priv->max_speed = pdata->max_speed;
>   	priv->phy_addr = 0;
>   
> +	if (dev_read_bool(dev, "use-ncsi"))
> +		priv->phy_mode = PHY_INTERFACE_MODE_NCSI;
> +
>   #ifdef CONFIG_PHY_ADDR
>   	priv->phy_addr = CONFIG_PHY_ADDR;
>   #endif
> @@ -592,7 +597,8 @@ static int ftgmac100_probe(struct udevice *dev)
>   	 * If DM MDIO is enabled, the MDIO bus will be initialized later in
>   	 * dm_eth_phy_connect
>   	 */
> -	if (!IS_ENABLED(CONFIG_DM_MDIO)) {
> +	if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI &&
> +	    !IS_ENABLED(CONFIG_DM_MDIO)) {
>   		ret = ftgmac100_mdio_init(dev);
>   		if (ret) {
>   			dev_err(dev, "Failed to initialize mdiobus: %d\n", ret);



More information about the U-Boot mailing list