[PATCH 4/4] ARM: dts: stm32: add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
Patrice CHOTARD
patrice.chotard at foss.st.com
Thu Jul 7 09:48:46 CEST 2022
Hi Patrick
On 7/5/22 16:55, Patrick Delaunay wrote:
> Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
>
> Only boards provided by STMicroelectronics are concerned:
> -STM32MP157A-DK1
> -STM32MP157C-DK2
> -STM32MP157C-ED1
> -STM32MP157C-EV1
>
> The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
> and the associated SCMI services, reset and clock.
>
> These device trees are only supported with stm32mp15_defconfig,
> with OP-TEE, SCMI and without SPL support.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
> ---
>
> arch/arm/dts/Makefile | 4 +
> arch/arm/dts/stm32mp15-scmi-u-boot.dtsi | 167 ++++++++++++++++++
> arch/arm/dts/stm32mp157a-dk1-scmi-u-boot.dtsi | 57 ++++++
> arch/arm/dts/stm32mp157c-dk2-scmi-u-boot.dtsi | 6 +
> arch/arm/dts/stm32mp157c-ed1-scmi-u-boot.dtsi | 47 +++++
> arch/arm/dts/stm32mp157c-ev1-scmi-u-boot.dtsi | 17 ++
> doc/board/st/stm32mp1.rst | 19 ++
> 7 files changed, 317 insertions(+)
> create mode 100644 arch/arm/dts/stm32mp15-scmi-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp157a-dk1-scmi-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp157c-dk2-scmi-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp157c-ed1-scmi-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp157c-ev1-scmi-u-boot.dtsi
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 87b210dbb01..a6b5295afc3 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -1171,13 +1171,17 @@ dtb-$(CONFIG_STM32MP13x) += \
>
> dtb-$(CONFIG_STM32MP15x) += \
> stm32mp157a-dk1.dtb \
> + stm32mp157a-dk1-scmi.dtb \
> stm32mp157a-icore-stm32mp1-ctouch2.dtb \
> stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
> stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
> stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \
> stm32mp157c-dk2.dtb \
> + stm32mp157c-dk2-scmi.dtb \
> stm32mp157c-ed1.dtb \
> + stm32mp157c-ed1-scmi.dtb \
> stm32mp157c-ev1.dtb \
> + stm32mp157c-ev1-scmi.dtb \
> stm32mp157c-odyssey.dtb \
> stm32mp15xx-dhcom-drc02.dtb \
> stm32mp15xx-dhcom-pdk2.dtb \
> diff --git a/arch/arm/dts/stm32mp15-scmi-u-boot.dtsi b/arch/arm/dts/stm32mp15-scmi-u-boot.dtsi
> new file mode 100644
> index 00000000000..314fc39a054
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15-scmi-u-boot.dtsi
> @@ -0,0 +1,167 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
> +/*
> + * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
> + */
> +
> +/ {
> + aliases {
> + gpio0 = &gpioa;
> + gpio1 = &gpiob;
> + gpio2 = &gpioc;
> + gpio3 = &gpiod;
> + gpio4 = &gpioe;
> + gpio5 = &gpiof;
> + gpio6 = &gpiog;
> + gpio7 = &gpioh;
> + gpio8 = &gpioi;
> + gpio9 = &gpioj;
> + gpio10 = &gpiok;
> + gpio25 = &gpioz;
> + pinctrl0 = &pinctrl;
> + pinctrl1 = &pinctrl_z;
> + };
> +
> + binman: binman {
> + multiple-images;
> + };
> +
> + soc {
> + u-boot,dm-pre-reloc;
> +
> + ddr: ddr at 5a003000 {
> + u-boot,dm-pre-reloc;
> +
> + compatible = "st,stm32mp1-ddr";
> +
> + reg = <0x5a003000 0x550
> + 0x5a004000 0x234>;
> +
> + status = "okay";
> + };
> + };
> +
> + /* need PSCI for sysreset during board_f */
> + psci {
> + u-boot,dm-pre-proper;
> + };
> +};
> +
> +&bsec {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioa {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpiob {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioc {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpiod {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioe {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpiof {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpiog {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioh {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioi {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioj {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpiok {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&gpioz {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&optee {
> + u-boot,dm-pre-proper;
> +};
> +
> +&iwdg2 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +/* pre-reloc probe = reserve video frame buffer in video_reserve() */
> +<dc {
> + u-boot,dm-pre-proper;
> +};
> +
> +/* temp = waiting kernel update */
> +&m4_rproc {
> + resets = <&scmi_reset RST_SCMI_MCU>,
> + <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
> + reset-names = "mcu_rst", "hold_boot";
> +};
> +
> +&pinctrl {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&pinctrl_z {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&rcc {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&scmi {
> + u-boot,dm-pre-proper;
> +};
> +
> +&usart1 {
> + resets = <&rcc USART1_R>;
> +};
> +
> +&usart2 {
> + resets = <&rcc USART2_R>;
> +};
> +
> +&usart3 {
> + resets = <&rcc USART3_R>;
> +};
> +
> +&uart4 {
> + resets = <&rcc UART4_R>;
> +};
> +
> +&uart5 {
> + resets = <&rcc UART5_R>;
> +};
> +
> +&usart6 {
> + resets = <&rcc USART6_R>;
> +};
> +
> +&uart7 {
> + resets = <&rcc UART7_R>;
> +};
> +
> +&uart8{
> + resets = <&rcc UART8_R>;
> +};
> diff --git a/arch/arm/dts/stm32mp157a-dk1-scmi-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-scmi-u-boot.dtsi
> new file mode 100644
> index 00000000000..2db045e7cec
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157a-dk1-scmi-u-boot.dtsi
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
> +/*
> + * Copyright : STMicroelectronics 2022
> + */
> +
> +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> +#include "stm32mp15-scmi-u-boot.dtsi"
> +#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
> +
> +/ {
> + aliases {
> + i2c3 = &i2c4;
> + usb0 = &usbotg_hs;
> + };
> +
> + config {
> + u-boot,boot-led = "heartbeat";
> + u-boot,error-led = "error";
> + u-boot,mmc-env-partition = "u-boot-env";
> + st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
> + st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + };
> +
> + led {
> + red {
> + label = "error";
> + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + status = "okay";
> + };
> + };
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&uart4 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_a {
> + u-boot,dm-pre-reloc;
> + pins1 {
> + u-boot,dm-pre-reloc;
> + };
> + pins2 {
> + u-boot,dm-pre-reloc;
> + /* pull-up on rx to avoid floating level */
> + bias-pull-up;
> + };
> +};
> +
> +&usbotg_hs {
> + u-boot,force-b-session-valid;
> +};
> diff --git a/arch/arm/dts/stm32mp157c-dk2-scmi-u-boot.dtsi b/arch/arm/dts/stm32mp157c-dk2-scmi-u-boot.dtsi
> new file mode 100644
> index 00000000000..5a8fc15ab2b
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dk2-scmi-u-boot.dtsi
> @@ -0,0 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
> +/*
> + * Copyright : STMicroelectronics 2022
> + */
> +
> +#include "stm32mp157a-dk1-scmi-u-boot.dtsi"
> diff --git a/arch/arm/dts/stm32mp157c-ed1-scmi-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-scmi-u-boot.dtsi
> new file mode 100644
> index 00000000000..54662f7e290
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-ed1-scmi-u-boot.dtsi
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
> +/*
> + * Copyright : STMicroelectronics 2022
> + */
> +
> +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> +#include "stm32mp15-scmi-u-boot.dtsi"
> +#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
> +
> +/ {
> + aliases {
> + i2c3 = &i2c4;
> + };
> +
> + config {
> + u-boot,boot-led = "heartbeat";
> + u-boot,error-led = "error";
> + u-boot,mmc-env-partition = "u-boot-env";
> + st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + };
> +
> + led {
> + red {
> + label = "error";
> + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + status = "okay";
> + };
> + };
> +};
> +
> +&uart4 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_a {
> + u-boot,dm-pre-reloc;
> + pins1 {
> + u-boot,dm-pre-reloc;
> + };
> + pins2 {
> + u-boot,dm-pre-reloc;
> + /* pull-up on rx to avoid floating level */
> + bias-pull-up;
> + };
> +};
> diff --git a/arch/arm/dts/stm32mp157c-ev1-scmi-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ev1-scmi-u-boot.dtsi
> new file mode 100644
> index 00000000000..71a94f9130a
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-ev1-scmi-u-boot.dtsi
> @@ -0,0 +1,17 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
> +/*
> + * Copyright : STMicroelectronics 2022
> + */
> +
> +#include "stm32mp157c-ed1-scmi-u-boot.dtsi"
> +
> +/ {
> + aliases {
> + gpio26 = &stmfx_pinctrl;
> + i2c1 = &i2c2;
> + i2c4 = &i2c5;
> + pinctrl2 = &stmfx_pinctrl;
> + spi0 = &qspi;
> + usb0 = &usbotg_hs;
> + };
> +};
> diff --git a/doc/board/st/stm32mp1.rst b/doc/board/st/stm32mp1.rst
> index 00f9b454421..3759df353ee 100644
> --- a/doc/board/st/stm32mp1.rst
> +++ b/doc/board/st/stm32mp1.rst
> @@ -77,6 +77,16 @@ Currently the following boards are supported:
> + stm32mp157c-ev1.dts
> + stm32mp15xx-dhcor-avenger96.dts
>
> +The SCMI variant of each board is supported by a specific "scmi" device tree:
> + + stm32mp157a-dk1-scmi.dts
> + + stm32mp157c-dk2-scmi.dts
> + + stm32mp157c-ed1-scmi.dts
> + + stm32mp157c-ev1-scmi.dts
> +
> +SCMI variant is used only with stm32mp15_defconfig, when the resources are
> +secured with RCC_TZCR.TZEN=1 in OP-TEE. The access to these reset and clock
> +resources are provided by OP-TEE and the associated SCMI services.
> +
> STM32MP13x
> ``````````
>
> @@ -136,6 +146,9 @@ TF-A_ (BL2) initialize the DDR and loads the next stage binaries from a FIP file
> the secure monitor to access to secure resources.
> + HW_CONFIG: The hardware configuration file = the U-Boot device tree
>
> +The scmi variant of each device tree is only support with OP-TEE as secure
> +monitor, with stm32mp15_defconfig.
> +
> The **Basic** boot chain with SPL (for STM32MP15x)
> ``````````````````````````````````````````````````
>
> @@ -248,6 +261,12 @@ Build Procedure
>
> a) trusted boot with FIP on STM32MP15x ev1::
>
> + # export KBUILD_OUTPUT=stm32mp15
> + # make stm32mp15_defconfig
> + # make DEVICE_TREE=stm32mp157c-ev1-scmi all
> +
> + or without SCMI support
> +
> # export KBUILD_OUTPUT=stm32mp15
> # make stm32mp15_defconfig
> # make DEVICE_TREE=stm32mp157c-ev1 all
Reviewed-by: Patrice Chotard <patrice.chotard at foss.st.com>
Thanks
Patrice
More information about the U-Boot
mailing list