[PATCH 2/2] ARM: dts: uniphier: Change phy-mode to RGMII-ID to enable delay pins
Kunihiko Hayashi
hayashi.kunihiko at socionext.com
Wed Jul 13 03:59:45 CEST 2022
UniPhier LD20, PXs2 and PXs3 boards have ethernet phy that has RX/TX delays
of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
So should set the phy-mode to "rgmii-id" to show that RX/TX delays are
enabled.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
---
arch/arm/dts/uniphier-ld20.dtsi | 2 +-
arch/arm/dts/uniphier-pxs2.dtsi | 2 +-
arch/arm/dts/uniphier-pxs3.dtsi | 4 ++--
3 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/dts/uniphier-ld20.dtsi b/arch/arm/dts/uniphier-ld20.dtsi
index 5e7143ed012f..4549935c421b 100644
--- a/arch/arm/dts/uniphier-ld20.dtsi
+++ b/arch/arm/dts/uniphier-ld20.dtsi
@@ -734,7 +734,7 @@
clocks = <&sys_clk 6>;
reset-names = "ether";
resets = <&sys_rst 6>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 0>;
diff --git a/arch/arm/dts/uniphier-pxs2.dtsi b/arch/arm/dts/uniphier-pxs2.dtsi
index 899ff379c9b8..7a8b6c10f4dc 100644
--- a/arch/arm/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/dts/uniphier-pxs2.dtsi
@@ -583,7 +583,7 @@
clocks = <&sys_clk 6>;
reset-names = "ether";
resets = <&sys_rst 6>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 0>;
diff --git a/arch/arm/dts/uniphier-pxs3.dtsi b/arch/arm/dts/uniphier-pxs3.dtsi
index c4344926d95d..004656c992b7 100644
--- a/arch/arm/dts/uniphier-pxs3.dtsi
+++ b/arch/arm/dts/uniphier-pxs3.dtsi
@@ -564,7 +564,7 @@
clocks = <&sys_clk 6>;
reset-names = "ether";
resets = <&sys_rst 6>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 0>;
@@ -585,7 +585,7 @@
clocks = <&sys_clk 7>;
reset-names = "ether";
resets = <&sys_rst 7>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
local-mac-address = [00 00 00 00 00 00];
socionext,syscon-phy-mode = <&soc_glue 1>;
--
2.7.4
More information about the U-Boot
mailing list