[PATCH 3/3] net: sun8i-emac: Use common syscon setup for R40

[Samuel Holland]

While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.

This change provides two benefits beyond the simplification:
 - R40 boards now respect the RX delays from the devicetree
 - This resolves a warning on architectures where readl/writel
   expect the address to have a pointer type, not phys_addr_t.

Signed-off-by: Samuel Holland <samuel at sholland.org>
---

 drivers/net/sun8i_emac.c | 29 ++++++++++++-----------------
 1 file changed, 12 insertions(+), 17 deletions(-)

diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c
index 9cca8fa4e0a1..75ecb58e1e45 100644
--- a/drivers/net/sun8i_emac.c
+++ b/drivers/net/sun8i_emac.c
@@ -162,7 +162,7 @@ struct emac_eth_dev {
 
 	enum emac_variant variant;
 	void *mac_reg;
-	phys_addr_t sysctl_reg;
+	void *sysctl_reg;
 	struct phy_device *phydev;
 	struct mii_dev *bus;
 	struct clk tx_clk;
@@ -317,18 +317,7 @@ static int sun8i_emac_set_syscon(struct sun8i_eth_pdata *pdata,
 {
 	u32 reg;
 
-	if (priv->variant == R40_GMAC) {
-		/* Select RGMII for R40 */
-		reg = readl(priv->sysctl_reg + 0x164);
-		reg |= SC_ETCS_INT_GMII |
-		       SC_EPIT |
-		       (CONFIG_GMAC_TX_DELAY << SC_ETXDC_OFFSET);
-
-		writel(reg, priv->sysctl_reg + 0x164);
-		return 0;
-	}
-
-	reg = readl(priv->sysctl_reg + 0x30);
+	reg = readl(priv->sysctl_reg);
 
 	reg = sun8i_emac_set_syscon_ephy(priv, reg);
 
@@ -369,7 +358,7 @@ static int sun8i_emac_set_syscon(struct sun8i_eth_pdata *pdata,
 		reg |= ((pdata->rx_delay_ps / 100) << SC_ERXDC_OFFSET)
 			 & SC_ERXDC_MASK;
 
-	writel(reg, priv->sysctl_reg + 0x30);
+	writel(reg, priv->sysctl_reg);
 
 	return 0;
 }
@@ -792,6 +781,7 @@ static int sun8i_emac_eth_of_to_plat(struct udevice *dev)
 	struct sun8i_eth_pdata *sun8i_pdata = dev_get_plat(dev);
 	struct eth_pdata *pdata = &sun8i_pdata->eth_pdata;
 	struct emac_eth_dev *priv = dev_get_priv(dev);
+	phys_addr_t syscon_base;
 	const fdt32_t *reg;
 	int node = dev_of_offset(dev);
 	int offset = 0;
@@ -837,13 +827,18 @@ static int sun8i_emac_eth_of_to_plat(struct udevice *dev)
 		      __func__);
 		return -EINVAL;
 	}
-	priv->sysctl_reg = fdt_translate_address((void *)gd->fdt_blob,
-						 offset, reg);
-	if (priv->sysctl_reg == FDT_ADDR_T_NONE) {
+
+	syscon_base = fdt_translate_address((void *)gd->fdt_blob, offset, reg);
+	if (syscon_base == FDT_ADDR_T_NONE) {
 		debug("%s: Cannot find syscon base address\n", __func__);
 		return -EINVAL;
 	}
 
+	if (priv->variant == R40_GMAC)
+		priv->sysctl_reg = (void *)syscon_base + 0x164;
+	else
+		priv->sysctl_reg = (void *)syscon_base + 0x30;
+
 	pdata->phy_interface = -1;
 	priv->phyaddr = -1;
 	priv->use_internal_phy = false;
-- 
2.35.1