[PATCH] arm: kirkwood: Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
Tony Dinh
mibodhi at gmail.com
Mon Mar 7 00:12:20 CET 2022
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi at gmail.com>
---
board/Marvell/sheevaplug/sheevaplug.c | 83 +++++----------------------
board/Marvell/sheevaplug/sheevaplug.h | 24 --------
configs/sheevaplug_defconfig | 1 +
include/configs/sheevaplug.h | 17 +++---
4 files changed, 22 insertions(+), 103 deletions(-)
delete mode 100644 board/Marvell/sheevaplug/sheevaplug.h
diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c
index 5952d158b2..26ee39ef77 100644
--- a/board/Marvell/sheevaplug/sheevaplug.c
+++ b/board/Marvell/sheevaplug/sheevaplug.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0+
/*
- * Copyright (C) 2021 Tony Dinh <mibodhi at gmail.com>
+ * Copyright (C) 2021-2022 Tony Dinh <mibodhi at gmail.com>
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla at marvell.com>
@@ -8,17 +8,21 @@
#include <common.h>
#include <init.h>
-#include <miiphy.h>
-#include <net.h>
+#include <netdev.h>
#include <asm/global_data.h>
#include <asm/mach-types.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
-#include "sheevaplug.h"
+#include <linux/bitops.h>
DECLARE_GLOBAL_DATA_PTR;
+#define SHEEVAPLUG_OE_LOW (~(0))
+#define SHEEVAPLUG_OE_HIGH (~(0))
+#define SHEEVAPLUG_OE_VAL_LOW BIT(29) /* USB_PWEN low */
+#define SHEEVAPLUG_OE_VAL_HIGH BIT(17) /* LED pin high */
+
int board_early_init_f(void)
{
/*
@@ -88,6 +92,11 @@ int board_early_init_f(void)
return 0;
}
+int board_eth_init(struct bd_info *bis)
+{
+ return cpu_eth_init(bis);
+}
+
int board_init(void)
{
/*
@@ -95,72 +104,8 @@ int board_init(void)
*/
gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
- /* adress of boot parameters */
+ /* address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
return 0;
}
-
-static int fdt_get_phy_addr(const char *path)
-{
- const void *fdt = gd->fdt_blob;
- const u32 *reg;
- const u32 *val;
- int node, phandle, addr;
-
- /* Find the node by its full path */
- node = fdt_path_offset(fdt, path);
- if (node >= 0) {
- /* Look up phy-handle */
- val = fdt_getprop(fdt, node, "phy-handle", NULL);
- if (val) {
- phandle = fdt32_to_cpu(*val);
- if (!phandle)
- return -1;
- /* Follow it to its node */
- node = fdt_node_offset_by_phandle(fdt, phandle);
- if (node) {
- /* Look up reg */
- reg = fdt_getprop(fdt, node, "reg", NULL);
- if (reg) {
- addr = fdt32_to_cpu(*reg);
- return addr;
- }
- }
- }
- }
- return -1;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
-{
- u16 reg;
- int phyaddr;
- char *name = "ethernet-controller at 72000";
- char *eth0_path = "/ocp at f1000000/ethernet-controller at 72000/ethernet0-port at 0";
-
- if (miiphy_set_current_dev(name))
- return;
-
- phyaddr = fdt_get_phy_addr(eth0_path);
- if (phyaddr < 0)
- return;
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, phyaddr);
-
- printf("88E1116 Initialized on %s\n", name);
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/sheevaplug/sheevaplug.h b/board/Marvell/sheevaplug/sheevaplug.h
deleted file mode 100644
index e026c1b53b..0000000000
--- a/board/Marvell/sheevaplug/sheevaplug.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- */
-
-#ifndef __SHEEVAPLUG_H
-#define __SHEEVAPLUG_H
-
-#define SHEEVAPLUG_OE_LOW (~(0))
-#define SHEEVAPLUG_OE_HIGH (~(0))
-#define SHEEVAPLUG_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
-#define SHEEVAPLUG_OE_VAL_HIGH (1 << 17) /* LED pin high */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __SHEEVAPLUG_H */
diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig
index 0c5031b2d2..41bf1065b0 100644
--- a/configs/sheevaplug_defconfig
+++ b/configs/sheevaplug_defconfig
@@ -50,6 +50,7 @@ CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_MVEBU_MMC=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
+CONFIG_PHY_MARVELL=y
CONFIG_DM_ETH=y
CONFIG_MVGBE=y
CONFIG_MII=y
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
index 4499a63aed..276c134a20 100644
--- a/include/configs/sheevaplug.h
+++ b/include/configs/sheevaplug.h
@@ -1,5 +1,6 @@
/* SPDX-License-Identifier: GPL-2.0+ */
/*
+ * (C) Copyright 2022 Tony Dinh <mibodhi at gmail.com>
* (C) Copyright 2009-2014
* Gerald Kerma <dreagle at doukki.net>
* Marvell Semiconductor <www.marvell.com>
@@ -11,13 +12,6 @@
#include "mv-common.h"
-/*
- * Environment variables configurations
- */
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
/*
* Environment is right behind U-Boot in flash. Make sure U-Boot
* doesn't grow into the environment area.
@@ -29,7 +23,7 @@
*/
#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
- "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS_DEFAULT \
+ "=ttyS0,115200 mtdparts=" CONFIG_MTDPARTS_DEFAULT \
"x_bootcmd_kernel=nand read 0x6400000 0x100000 0x400000\0" \
"x_bootcmd_usb=usb start\0" \
"x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
@@ -37,13 +31,16 @@
/*
* Ethernet Driver configuration
*/
-#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_RESET_PHY_R
+#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */
+#endif
/*
* SATA driver configuration
+ *
+ * The original Sheevaplug board does not have eSATA, so allow SATA to be disabled.
*/
#ifdef CONFIG_SATA
#define CONFIG_LBA48
--
2.30.2
More information about the U-Boot
mailing list