[PATCH] warp7: Remove UART initialization code

[Fabio Estevam]

From: Fabio Estevam <festevam at denx.de>

With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.

Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.

Remove the now unneeded board UART initialization.

Signed-off-by: Fabio Estevam <festevam at denx.de>
---
 arch/arm/dts/imx7s-warp-u-boot.dtsi | 16 ++++++++++++++++
 arch/arm/dts/imx7s.dtsi             |  2 +-
 board/warp7/warp7.c                 | 20 --------------------
 configs/warp7_defconfig             |  1 +
 4 files changed, 18 insertions(+), 21 deletions(-)

diff --git a/arch/arm/dts/imx7s-warp-u-boot.dtsi b/arch/arm/dts/imx7s-warp-u-boot.dtsi
index 6319840b1ce3..bc4b5745fc7c 100644
--- a/arch/arm/dts/imx7s-warp-u-boot.dtsi
+++ b/arch/arm/dts/imx7s-warp-u-boot.dtsi
@@ -8,3 +8,19 @@
         stdout-path = &uart1;
     };
 };
+
+&aips3 {
+	u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart1 {
+	u-boot,dm-pre-reloc;
+};
+
+&soc {
+	u-boot,dm-pre-reloc;
+};
+
+&uart1 {
+	u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/imx7s.dtsi b/arch/arm/dts/imx7s.dtsi
index 483824fc06e6..cf0206dd0f08 100644
--- a/arch/arm/dts/imx7s.dtsi
+++ b/arch/arm/dts/imx7s.dtsi
@@ -184,7 +184,7 @@
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
diff --git a/board/warp7/warp7.c b/board/warp7/warp7.c
index c5c5433048dd..95b8e82dd1cc 100644
--- a/board/warp7/warp7.c
+++ b/board/warp7/warp7.c
@@ -27,9 +27,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \
-			PAD_CTL_HYS)
-
 int dram_init(void)
 {
 	gd->ram_size = PHYS_SDRAM_SIZE;
@@ -46,23 +43,6 @@ static iomux_v3_cfg_t const wdog_pads[] = {
 	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
-static iomux_v3_cfg_t const uart1_pads[] = {
-	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-};
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-
-	return 0;
-}
-
 #ifdef CONFIG_DM_PMIC
 int power_init_board(void)
 {
diff --git a/configs/warp7_defconfig b/configs/warp7_defconfig
index a76565edfd4a..be69174217b0 100644
--- a/configs/warp7_defconfig
+++ b/configs/warp7_defconfig
@@ -19,6 +19,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="mmc dev ${mmcdev};mmc dev ${mmcdev}; if mmc rescan; then run do_bootscript_hab;if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; fi; fi; fi"
+# CONFIG_BOARD_EARLY_INIT_F is not set
 CONFIG_HUSH_PARSER=y
 # CONFIG_CMD_BOOTD is not set
 CONFIG_CMD_BOOTZ=y
-- 
2.25.1