[PATCH] arm: kirkwood: Add nas440 board, Marvell 88SE6121 AHCI
Hajo Noerenberg
hajo-uboot at noerenberg.de
Mon Mar 28 10:36:36 CEST 2022
Hi Pali,
Am 28.03.2022 um 10:04 schrieb Pali Rohár:
> On Monday 28 March 2022 09:57:41 Hajo Noerenberg wrote:
>> I wonder if it would be a good idea to submit adding the PCI-ids for the 88SE6121 controller (drivers/ata/ahci-pci.c) as a separate patch. The controller is not specific to the NAS440, to my knowledge it is also used on the Iomega ix4-200d for example.
>
> Why is this patch needed?
Sorry, but that's beyond my knowledge. Without the PCI ids the controller is handled by the generic driver.
>
> Could you please send 'lspci -nn -vv' output from Linux?
Please find the logs below. For reference I have also attached the U-Boot logs (with / without PCI ids).
Side note: as written in my first e-mail, I can access all hard disks and load files within U-Boot. Under Linux there are 'failed to IDENTIFY' errors.
Regards,
Hajo
root at nas440:~# lspci -nn -vv
00:01.0 PCI bridge [0604]: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC [11ab:6281] (rev 03) (prog-if 00 [Normal decode])
Device tree node: /sys/firmware/devicetree/base/mbus at f1000000/pcie at 82000000/pcie at 1,0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00010000-00010fff [size=4K]
Memory behind bridge: e0000000-e00fffff [size=1M]
Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
Expansion ROM at e0100000 [virtual] [disabled] [size=2K]
BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <256ns, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 128 bytes, Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCap: CRSVisible-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
01:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6111/6121 SATA II / PATA Controller [11ab:6121] (rev b2) (prog-if 8f [PCI native mode controller, supports both channels switched to ISA compatibility mode, supports bus mastering])
Subsystem: Marvell Technology Group Ltd. 88SE6111/6121 1/2 port SATA II + 1 port PATA Controller [11ab:6121]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at 10010 [size=8]
Region 1: I/O ports at 10020 [size=4]
Region 2: I/O ports at 10018 [size=8]
Region 3: I/O ports at 10024 [size=4]
Region 4: I/O ports at 10000 [size=16]
Region 5: Memory at e0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Exit Latency L0s <256ns
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 1f, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: ahci
Kernel modules: ahci
/* U-Boot with 88SE6121 PCI ids: */
nas440> version
U-Boot 2022.04-rc3-00003-ge177499b76-dirty (Mar 03 2022 - 16:58:16 +0100)
NAS 440
nas440> pci long
Found PCI device 00.00.00:
vendor ID = 0x11ab
device ID = 0x6281
command register ID = 0x0007
status register = 0x0010
revision ID = 0x03
class code = 0x06 (Bridge device)
sub class code = 0x04
programming interface = 0x00
cache line = 0x00
latency time = 0x00
header type = 0x01
BIST = 0x00
base address 0 = 0x00000000
base address 1 = 0x00000000
primary bus number = 0x00
secondary bus number = 0x01
subordinate bus number = 0x01
secondary latency timer = 0x00
IO base = 0x01
IO limit = 0x01
secondary status = 0x0000
memory base = 0x9000
memory limit = 0x9000
prefetch memory base = 0xfff1
prefetch memory limit = 0x0001
prefetch memory base upper = 0x00000000
prefetch memory limit upper = 0x00000000
IO base upper 16 bits = 0xc000
IO limit upper 16 bits = 0xc000
expansion ROM base address = 0x00000000
interrupt line = 0x00
interrupt pin = 0x01
bridge control = 0x0000
Found PCI device 01.00.00:
vendor ID = 0x11ab
device ID = 0x6121
command register ID = 0x0007
status register = 0x0010
revision ID = 0xb2
class code = 0x01 (Mass storage controller)
sub class code = 0x01
programming interface = 0x8f
cache line = 0x08
latency time = 0x00
header type = 0x00
BIST = 0x00
base address 0 = 0xc0000001
base address 1 = 0xc0000009
base address 2 = 0xc0000011
base address 3 = 0xc0000019
base address 4 = 0xc0000021
base address 5 = 0x90000000
cardBus CIS pointer = 0x00000000
sub system vendor ID = 0x11ab
sub system ID = 0x6121
expansion ROM base address = 0x00000000
interrupt line = 0x00
interrupt pin = 0x01
min Grant = 0x00
max Latency = 0x00
nas440>
nas440> scsi scan
scanning bus for devices...
Target spinup took 0 ms.
Target spinup took 0 ms.
SATA link 2 timeout.
AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
flags: 64bit ncq stag led pmp slum part
Device 0: (0:0) Vendor: ATA Prod.: WDC WD3202ABYS-0 Rev: 02.0
Type: Hard Disk
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Device 1: (1:0) Vendor: ATA Prod.: FUJITSU MHZ2160B Rev: 0084
Type: Hard Disk
Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
nas440>
nas440> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
simple_bus 0 [ + ] simple_bus |-- mbus at f1000000
misc 0 [ + ] pcie_mvebu_base | `-- pcie at 82000000
pci 0 [ + ] pcie_mvebu | `-- pcie0.0
pci 1 [ + ] pci_bridge_drv | `-- pci_0:0.0
ahci 1 [ + ] ahci_pci | `-- ahci_pci
scsi 0 [ + ] ahci_scsi | `-- ahci_scsi
blk 0 [ ] scsi_blk | |-- ahci_scsi.id0lun0
blk 1 [ ] scsi_blk | `-- ahci_scsi.id1lun0
simple_bus 1 [ + ] simple_bus |-- ocp at f1000000
gpio 0 [ ] gpio_mvebu | |-- gpio at 10100
gpio 1 [ ] gpio_mvebu | |-- gpio at 10140
usb 0 [ ] ehci_mvebu | |-- ehci at 50000
ethernet 0 [ + ] mvgbe | |-- ethernet-controller at 72000
ethernet 1 [ + ] mvgbe | |-- ethernet-controller at 76000
rtc 0 [ ] rtc-mv | |-- rtc at 10300
ahci 0 [ ] sata_mv_ahci | `-- sata at 80000
simple_bus 2 [ ] simple_bus `-- regulators
nas440>
/* U-Boot without 88SE6121 PCI ids: */
nas440> pci enum
pcie0.0: Link up
nas440> scsi scan
scanning bus for devices...
nas440> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
simple_bus 0 [ + ] simple_bus |-- mbus at f1000000
misc 0 [ + ] pcie_mvebu_base | `-- pcie at 82000000
pci 0 [ + ] pcie_mvebu | `-- pcie0.0
pci 1 [ + ] pci_bridge_drv | `-- pci_0:0.0
pci_generi 0 [ ] pci_generic_drv | `-- pci_1:0.0
simple_bus 1 [ + ] simple_bus |-- ocp at f1000000
gpio 0 [ ] gpio_mvebu | |-- gpio at 10100
gpio 1 [ ] gpio_mvebu | |-- gpio at 10140
usb 0 [ ] ehci_mvebu | |-- ehci at 50000
ethernet 0 [ + ] mvgbe | |-- ethernet-controller at 72000
ethernet 1 [ + ] mvgbe | |-- ethernet-controller at 76000
rtc 0 [ ] rtc-mv | |-- rtc at 10300
ahci 0 [ ] sata_mv_ahci | `-- sata at 80000
simple_bus 2 [ ] simple_bus `-- regulators
nas440>
More information about the U-Boot
mailing list