[PATCH 11/52] mips: octeon: Add cvmx-helper-board.c

Stefan Roese sr at denx.de
Wed Mar 30 12:06:47 CEST 2022


From: Aaron Williams <awilliams at marvell.com>

Import cvmx-helper-board.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.

Signed-off-by: Aaron Williams <awilliams at marvell.com>
Signed-off-by: Stefan Roese <sr at denx.de>
---
 arch/mips/mach-octeon/cvmx-helper-board.c | 2030 +++++++++++++++++++++
 1 file changed, 2030 insertions(+)
 create mode 100644 arch/mips/mach-octeon/cvmx-helper-board.c

diff --git a/arch/mips/mach-octeon/cvmx-helper-board.c b/arch/mips/mach-octeon/cvmx-helper-board.c
new file mode 100644
index 000000000000..783beb4b178e
--- /dev/null
+++ b/arch/mips/mach-octeon/cvmx-helper-board.c
@@ -0,0 +1,2030 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018-2022 Marvell International Ltd.
+ *
+ * Helper functions to abstract board specific data about
+ * network ports from the rest of the cvmx-helper files.
+ */
+
+#include <i2c.h>
+#include <log.h>
+#include <malloc.h>
+#include <net.h>
+#include <linux/delay.h>
+
+#include <mach/cvmx-regs.h>
+#include <mach/cvmx-csr.h>
+#include <mach/cvmx-bootmem.h>
+#include <mach/octeon-model.h>
+#include <mach/octeon_fdt.h>
+#include <mach/cvmx-helper.h>
+#include <mach/cvmx-helper-board.h>
+#include <mach/cvmx-helper-cfg.h>
+#include <mach/cvmx-helper-fdt.h>
+#include <mach/cvmx-helper-gpio.h>
+
+#include <mach/cvmx-smix-defs.h>
+#include <mach/cvmx-mdio.h>
+#include <mach/cvmx-qlm.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static bool sfp_parsed;
+
+static int __cvmx_helper_78xx_parse_phy(struct cvmx_phy_info *phy_info,
+					int ipd_port);
+static int __get_phy_info_from_dt(cvmx_phy_info_t *phy_info, int ipd_port);
+
+/**
+ * Writes to a Microsemi VSC7224 16-bit register
+ *
+ * @param[in]	i2c_bus	i2c bus data structure (must be enabled)
+ * @param	addr	Address of VSC7224 on the i2c bus
+ * @param	reg	8-bit register number to write to
+ * @param	val	16-bit value to write
+ *
+ * @return	0 for success
+ */
+static int cvmx_write_vsc7224_reg(const struct cvmx_fdt_i2c_bus_info *i2c_bus,
+				  u8 addr, u8 reg, u16 val)
+{
+	struct udevice *dev;
+	u8 buffer[2];
+	int ret;
+
+	ret = i2c_get_chip(i2c_bus->i2c_bus, addr, 1, &dev);
+	if (ret) {
+		debug("Cannot find I2C device: %d\n", ret);
+		return -1;
+	}
+
+	ret = dm_i2c_write(dev, reg, buffer, 2);
+	if (ret) {
+		debug("Cannot write I2C device: %d\n", ret);
+		return -1;
+	}
+
+	return 0;
+}
+
+/**
+ * Writes to a Microsemi VSC7224 16-bit register
+ *
+ * @param[in]	i2c_bus	i2c bus data structure (must be enabled)
+ * @param	addr	Address of VSC7224 on the i2c bus
+ * @param	reg	8-bit register number to write to
+ *
+ * @return	16-bit value or error if < 0
+ */
+static int cvmx_read_vsc7224_reg(const struct cvmx_fdt_i2c_bus_info *i2c_bus,
+				 u8 addr, u8 reg)
+{
+	struct udevice *dev;
+	u8 buffer[2];
+	int ret;
+
+	ret = i2c_get_chip(i2c_bus->i2c_bus, addr, 1, &dev);
+	if (ret) {
+		debug("Cannot find I2C device: %d\n", ret);
+		return -1;
+	}
+
+	ret = dm_i2c_read(dev, reg, buffer, 2);
+	if (ret) {
+		debug("Cannot read I2C device: %d\n", ret);
+		return -1;
+	}
+
+	return (buffer[0] << 8) | buffer[1];
+}
+
+/**
+ * @INTERNAL
+ * Return loss of signal
+ *
+ * @param	xiface	xinterface number
+ * @param	index	port index on interface
+ *
+ * @return	0 if signal present, 1 if loss of signal.
+ *
+ * @NOTE:	A result of 0 is possible in some cases where the signal is
+ *		not present.
+ *
+ * This is for use with __cvmx_qlm_rx_equilization
+ */
+int __cvmx_helper_get_los(int xiface, int index)
+{
+	struct cvmx_fdt_sfp_info *sfp;
+	struct cvmx_vsc7224_chan *vsc7224_chan;
+	struct cvmx_vsc7224 *vsc7224;
+	int los = 0;
+	int val;
+	int mode = cvmx_helper_interface_get_mode(xiface);
+
+	sfp = cvmx_helper_cfg_get_sfp_info(xiface, index);
+
+	/* Check all SFP slots in the group
+	 * NOTE: Usually there is only one SFP or QSFP slot except in the case
+	 *	 where multiple SFP+ slots are grouped together for XLAUI mode.
+	 */
+	while (sfp && sfp->check_mod_abs) {
+		los = sfp->check_mod_abs(sfp, sfp->mod_abs_data);
+		if (los >= 0)
+			cvmx_sfp_validate_module(sfp, mode);
+		if (los || los < 0) {
+			debug("%s(0x%x, %d): los detected (mod_abs) los: %d\n",
+			      __func__, xiface, index, los);
+			return 1;
+		}
+		vsc7224_chan = sfp->vsc7224_chan;
+		while (vsc7224_chan) {
+			u64 done;
+			int channel_num = vsc7224_chan->lane;
+			int los_bit = 1 << channel_num;
+			int lol_bit = 0x10 << channel_num;
+
+			/* We only care about receive channels so skip rx.
+			 * Also, in XFI mode we don't care about different
+			 * XFI ports so skip those.
+			 */
+			if (vsc7224_chan->is_tx ||
+			    vsc7224_chan->index != index ||
+			    vsc7224_chan->xiface != xiface) {
+				vsc7224_chan = vsc7224_chan->next;
+				continue;
+			}
+
+			vsc7224 = vsc7224_chan->vsc7224;
+			/* Poll for LoS/LoL for 2ms */
+			cvmx_write_vsc7224_reg(vsc7224->i2c_bus,
+					       vsc7224->i2c_addr, 0x7f, 0x40);
+			done = 20;
+			do {
+				val = cvmx_read_vsc7224_reg(vsc7224->i2c_bus,
+							    vsc7224->i2c_addr,
+							    0xc0);
+				val &= (los_bit | lol_bit);
+				if (val) {
+					debug("%s(0x%x, %d): LOS/LOL detected from VSC7224: 0x%x\n",
+					      __func__, xiface, index, val);
+					return 1;
+				}
+				udelay(100);
+			} while (done--);
+
+			/* Move to the next channel */
+			vsc7224_chan = vsc7224_chan->next;
+		}
+		/* Move to the next SFP+ slot */
+		sfp = sfp->next;
+	}
+	debug("%s(0x%x, %d): los: 0\n", __func__, xiface, index);
+	return 0;
+}
+
+/**
+ * Function called whenever mod_abs/mod_prs has changed for Microsemi VSC7224
+ *
+ * @param	sfp	pointer to SFP data structure
+ * @param	val	1 if absent, 0 if present, otherwise not set
+ * @param	data	user-defined data
+ *
+ * @return	0 for success, -1 on error
+ */
+int cvmx_sfp_vsc7224_mod_abs_changed(struct cvmx_fdt_sfp_info *sfp, int val,
+				     void *data)
+{
+	int err;
+	struct cvmx_sfp_mod_info *mod_info;
+	int length;
+	struct cvmx_vsc7224 *vsc7224;
+	struct cvmx_vsc7224_chan *vsc7224_chan;
+	struct cvmx_vsc7224_tap *taps, *match = NULL;
+	int i;
+
+	debug("%s(%s, %d, %p): Module %s\n", __func__, sfp->name, val, data,
+	      val ? "absent" : "present");
+	if (val)
+		return 0;
+
+	/* We're here if we detect that the module is now present */
+	err = cvmx_sfp_read_i2c_eeprom(sfp);
+	if (err) {
+		debug("%s: Error reading the SFP module eeprom for %s\n",
+		      __func__, sfp->name);
+		return err;
+	}
+	mod_info = &sfp->sfp_info;
+
+	if (!mod_info->valid || !sfp->valid) {
+		debug("%s: Module data is invalid\n", __func__);
+		return -1;
+	}
+
+	vsc7224_chan = sfp->vsc7224_chan;
+	while (vsc7224_chan) {
+		/* We don't do any rx tuning */
+		if (!vsc7224_chan->is_tx) {
+			vsc7224_chan = vsc7224_chan->next;
+			continue;
+		}
+
+		/* Walk through all the channels */
+		taps = vsc7224_chan->taps;
+		if (mod_info->limiting)
+			length = 0;
+		else
+			length = mod_info->max_copper_cable_len;
+		debug("%s: limiting: %d, length: %d\n", __func__,
+		      mod_info->limiting, length);
+
+		/* Find a matching length in the taps table */
+		for (i = 0; i < vsc7224_chan->num_taps; i++) {
+			if (length >= taps->len)
+				match = taps;
+			taps++;
+		}
+		if (!match) {
+			debug("%s(%s, %d, %p): Error: no matching tap for length %d\n",
+			      __func__, sfp->name, val, data, length);
+			return -1;
+		}
+		debug("%s(%s): Applying %cx taps to vsc7224 %s:%d for cable length %d+\n",
+		      __func__, sfp->name, vsc7224_chan->is_tx ? 't' : 'r',
+		      vsc7224_chan->vsc7224->name, vsc7224_chan->lane,
+		      match->len);
+		/* Program the taps */
+		vsc7224 = vsc7224_chan->vsc7224;
+		cvmx_write_vsc7224_reg(vsc7224->i2c_bus, vsc7224->i2c_addr,
+				       0x7f, vsc7224_chan->lane);
+		if (!vsc7224_chan->maintap_disable)
+			cvmx_write_vsc7224_reg(vsc7224->i2c_bus,
+					       vsc7224->i2c_addr, 0x99,
+					       match->main_tap);
+		if (!vsc7224_chan->pretap_disable)
+			cvmx_write_vsc7224_reg(vsc7224->i2c_bus,
+					       vsc7224->i2c_addr, 0x9a,
+					       match->pre_tap);
+		if (!vsc7224_chan->posttap_disable)
+			cvmx_write_vsc7224_reg(vsc7224->i2c_bus,
+					       vsc7224->i2c_addr, 0x9b,
+					       match->post_tap);
+
+		/* Re-use val and disable taps if needed */
+		if (vsc7224_chan->maintap_disable ||
+		    vsc7224_chan->pretap_disable ||
+		    vsc7224_chan->posttap_disable) {
+			val = cvmx_read_vsc7224_reg(vsc7224->i2c_bus,
+						    vsc7224->i2c_addr, 0x97);
+			if (vsc7224_chan->maintap_disable)
+				val |= 0x800;
+			if (vsc7224_chan->pretap_disable)
+				val |= 0x1000;
+			if (vsc7224_chan->posttap_disable)
+				val |= 0x400;
+			cvmx_write_vsc7224_reg(vsc7224->i2c_bus,
+					       vsc7224->i2c_addr, 0x97, val);
+		}
+		vsc7224_chan = vsc7224_chan->next;
+	}
+
+	return err;
+}
+
+/**
+ * Update the mod_abs and error LED
+ *
+ * @param	ipd_port	ipd port number
+ * @param	link		link information
+ */
+static void __cvmx_helper_update_sfp(int ipd_port,
+				     struct cvmx_fdt_sfp_info *sfp_info,
+				     cvmx_helper_link_info_t link)
+{
+	debug("%s(%d): checking mod_abs\n", __func__, ipd_port);
+
+	cvmx_sfp_check_mod_abs(sfp_info, sfp_info->mod_abs_data);
+}
+
+static void cvmx_sfp_update_link(struct cvmx_fdt_sfp_info *sfp,
+				 cvmx_helper_link_info_t link)
+{
+	while (sfp) {
+		debug("%s(%s): checking mod_abs\n", __func__, sfp->name);
+		if (link.s.link_up && sfp->last_mod_abs)
+			cvmx_sfp_check_mod_abs(sfp, sfp->mod_abs_data);
+		sfp = sfp->next_iface_sfp;
+	}
+}
+
+/**
+ * @INTERNAL
+ * This function is used ethernet ports link speed. This functions uses the
+ * device tree information to determine the phy address and type of PHY.
+ * The only supproted PHYs are Marvell and Broadcom.
+ *
+ * @param ipd_port IPD input port associated with the port we want to get link
+ *                 status for.
+ *
+ * @return The ports link status. If the link isn't fully resolved, this must
+ *         return zero.
+ */
+cvmx_helper_link_info_t __cvmx_helper_board_link_get_from_dt(int ipd_port)
+{
+	cvmx_helper_link_info_t result;
+	cvmx_phy_info_t *phy_info = NULL;
+	cvmx_phy_info_t local_phy_info;
+	int xiface = 0, index = 0;
+	bool use_inband = false;
+	struct cvmx_fdt_sfp_info *sfp_info;
+	const void *fdt_addr = CASTPTR(const void *, gd->fdt_blob);
+
+	result.u64 = 0;
+
+	if (ipd_port >= 0) {
+		int mode;
+
+		xiface = cvmx_helper_get_interface_num(ipd_port);
+		index = cvmx_helper_get_interface_index_num(ipd_port);
+		mode = cvmx_helper_interface_get_mode(xiface);
+		if (!cvmx_helper_get_port_autonegotiation(xiface, index)) {
+			result.s.link_up = 1;
+			result.s.full_duplex = 1;
+			switch (mode) {
+			case CVMX_HELPER_INTERFACE_MODE_RGMII:
+			case CVMX_HELPER_INTERFACE_MODE_GMII:
+			case CVMX_HELPER_INTERFACE_MODE_SGMII:
+			case CVMX_HELPER_INTERFACE_MODE_QSGMII:
+			case CVMX_HELPER_INTERFACE_MODE_AGL:
+			case CVMX_HELPER_INTERFACE_MODE_SPI:
+				if (OCTEON_IS_MODEL(OCTEON_CN70XX)) {
+					struct cvmx_xiface xi =
+						cvmx_helper_xiface_to_node_interface(
+							xiface);
+					u64 gbaud = cvmx_qlm_get_gbaud_mhz(0);
+
+					result.s.speed = gbaud * 8 / 10;
+					if (cvmx_qlm_get_dlm_mode(
+						    0, xi.interface) ==
+					    CVMX_QLM_MODE_SGMII)
+						result.s.speed >>= 1;
+					else
+						result.s.speed >>= 2;
+				} else {
+					result.s.speed = 1000;
+				}
+				break;
+			case CVMX_HELPER_INTERFACE_MODE_RXAUI:
+			case CVMX_HELPER_INTERFACE_MODE_XAUI:
+			case CVMX_HELPER_INTERFACE_MODE_10G_KR:
+			case CVMX_HELPER_INTERFACE_MODE_XFI:
+				result.s.speed = 10000;
+				break;
+			case CVMX_HELPER_INTERFACE_MODE_XLAUI:
+			case CVMX_HELPER_INTERFACE_MODE_40G_KR4:
+				result.s.speed = 40000;
+				break;
+			default:
+				break;
+			}
+
+			sfp_info = cvmx_helper_cfg_get_sfp_info(xiface, index);
+			/* Initialize the SFP info if it hasn't already been
+			 * done.
+			 */
+			if (!sfp_info && !sfp_parsed) {
+				cvmx_sfp_parse_device_tree(fdt_addr);
+				sfp_parsed = true;
+				cvmx_sfp_read_all_modules();
+				sfp_info = cvmx_helper_cfg_get_sfp_info(xiface,
+									index);
+			}
+			/* If the link is down or the link is up but we still
+			 * register the module as being absent, re-check
+			 * mod_abs.
+			 */
+			cvmx_sfp_update_link(sfp_info, result);
+
+			cvmx_helper_update_link_led(xiface, index, result);
+
+			return result;
+		}
+		phy_info = cvmx_helper_get_port_phy_info(xiface, index);
+		if (!phy_info) {
+			debug("%s: phy info not saved in config, allocating for 0x%x:%d\n",
+			      __func__, xiface, index);
+
+			phy_info = (cvmx_phy_info_t *)cvmx_bootmem_alloc(
+				sizeof(*phy_info), 0);
+			if (!phy_info) {
+				debug("%s: Out of memory\n", __func__);
+				return result;
+			}
+			memset(phy_info, 0, sizeof(*phy_info));
+			phy_info->phy_addr = -1;
+			debug("%s: Setting phy info for 0x%x:%d to %p\n",
+			      __func__, xiface, index, phy_info);
+			cvmx_helper_set_port_phy_info(xiface, index, phy_info);
+		}
+	} else {
+		/* For management ports we don't store the PHY information
+		 * so we use a local copy instead.
+		 */
+		phy_info = &local_phy_info;
+		memset(phy_info, 0, sizeof(*phy_info));
+		phy_info->phy_addr = -1;
+	}
+
+	if (phy_info->phy_addr == -1) {
+		if (octeon_has_feature(OCTEON_FEATURE_BGX)) {
+			if (__cvmx_helper_78xx_parse_phy(phy_info, ipd_port)) {
+				phy_info->phy_addr = -1;
+				use_inband = true;
+			}
+		} else if (__get_phy_info_from_dt(phy_info, ipd_port) < 0) {
+			phy_info->phy_addr = -1;
+			use_inband = true;
+		}
+	}
+
+	/* If we can't get the PHY info from the device tree then try
+	 * the inband state.
+	 */
+	if (use_inband) {
+		result.s.full_duplex = 1;
+		result.s.link_up = 1;
+		result.s.speed = 1000;
+		return result;
+	}
+
+	if (phy_info->phy_addr < 0)
+		return result;
+
+	if (phy_info->link_function)
+		result = phy_info->link_function(phy_info);
+	else
+		result = cvmx_helper_link_get(ipd_port);
+
+	sfp_info = cvmx_helper_cfg_get_sfp_info(xiface, index);
+	while (sfp_info) {
+		/* If the link is down or the link is up but we still register
+		 * the module as being absent, re-check mod_abs.
+		 */
+		if (!result.s.link_up ||
+		    (result.s.link_up && sfp_info->last_mod_abs))
+			__cvmx_helper_update_sfp(ipd_port, sfp_info, result);
+		sfp_info = sfp_info->next_iface_sfp;
+	}
+
+	return result;
+}
+
+cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port)
+{
+	cvmx_helper_link_info_t result;
+
+	/* Unless we fix it later, all links are defaulted to down */
+	result.u64 = 0;
+
+	return __cvmx_helper_board_link_get_from_dt(ipd_port);
+}
+
+void cvmx_helper_update_link_led(int xiface, int index,
+				 cvmx_helper_link_info_t result)
+{
+}
+
+void cvmx_helper_leds_show_error(struct cvmx_phy_gpio_leds *leds, bool error)
+{
+}
+
+int __cvmx_helper_board_interface_probe(int interface, int supported_ports)
+{
+	return supported_ports;
+}
+
+/**
+ * Returns the Ethernet node offset in the device tree
+ *
+ * @param     fdt_addr - pointer to flat device tree in memory
+ * @param     aliases    - offset of alias in device tree
+ * @param     ipd_port - ipd port number to look up
+ *
+ * @returns   offset of Ethernet node if >= 0, error if -1
+ */
+int __pip_eth_node(const void *fdt_addr, int aliases, int ipd_port)
+{
+	char name_buffer[20];
+	const char *pip_path;
+	int pip, iface, eth;
+	int interface_num = cvmx_helper_get_interface_num(ipd_port);
+	int interface_index = cvmx_helper_get_interface_index_num(ipd_port);
+	cvmx_helper_interface_mode_t interface_mode =
+		cvmx_helper_interface_get_mode(interface_num);
+
+	/* The following are not found in the device tree */
+	switch (interface_mode) {
+	case CVMX_HELPER_INTERFACE_MODE_ILK:
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+	case CVMX_HELPER_INTERFACE_MODE_SRIO:
+		debug("ERROR: No node expected for interface: %d, port: %d, mode: %s\n",
+		      interface_index, ipd_port,
+		      cvmx_helper_interface_mode_to_string(interface_mode));
+		return -1;
+	default:
+		break;
+	}
+	pip_path = (const char *)fdt_getprop(fdt_addr, aliases, "pip", NULL);
+	if (!pip_path) {
+		debug("ERROR: pip path not found in device tree\n");
+		return -1;
+	}
+	pip = fdt_path_offset(fdt_addr, pip_path);
+	debug("ipdd_port=%d pip_path=%s pip=%d ", ipd_port, pip_path, pip);
+	if (pip < 0) {
+		debug("ERROR: pip not found in device tree\n");
+		return -1;
+	}
+	snprintf(name_buffer, sizeof(name_buffer), "interface@%d",
+		 interface_num);
+	iface = fdt_subnode_offset(fdt_addr, pip, name_buffer);
+	debug("iface=%d ", iface);
+	if (iface < 0) {
+		debug("ERROR : pip intf %d not found in device tree\n",
+		      interface_num);
+		return -1;
+	}
+	snprintf(name_buffer, sizeof(name_buffer), "ethernet@%x",
+		 interface_index);
+	eth = fdt_subnode_offset(fdt_addr, iface, name_buffer);
+	debug("eth=%d\n", eth);
+	if (eth < 0) {
+		debug("ERROR : pip interface@%d ethernet@%d not found in device tree\n",
+		      interface_num, interface_index);
+		return -1;
+	}
+	return eth;
+}
+
+int __mix_eth_node(const void *fdt_addr, int aliases, int interface_index)
+{
+	char name_buffer[20];
+	const char *mix_path;
+	int mix;
+
+	snprintf(name_buffer, sizeof(name_buffer), "mix%d", interface_index);
+	mix_path =
+		(const char *)fdt_getprop(fdt_addr, aliases, name_buffer, NULL);
+	if (!mix_path) {
+		debug("ERROR: mix%d path not found in device tree\n",
+		      interface_index);
+	}
+	mix = fdt_path_offset(fdt_addr, mix_path);
+	if (mix < 0) {
+		debug("ERROR: %s not found in device tree\n", mix_path);
+		return -1;
+	}
+	return mix;
+}
+
+static int __mdiobus_addr_to_unit(u32 addr)
+{
+	int unit = (addr >> 7) & 3;
+
+	if (!OCTEON_IS_MODEL(OCTEON_CN68XX) && !OCTEON_IS_MODEL(OCTEON_CN78XX))
+		unit >>= 1;
+	return unit;
+}
+
+/**
+ * Parse the muxed MDIO interface information from the device tree
+ *
+ * @param phy_info - pointer to phy info data structure to update
+ * @param mdio_offset - offset of MDIO bus
+ * @param mux_offset - offset of MUX, parent of mdio_offset
+ *
+ * @return 0 for success or -1
+ */
+static int __get_muxed_mdio_info_from_dt(cvmx_phy_info_t *phy_info,
+					 int mdio_offset, int mux_offset)
+{
+	const void *fdt_addr = CASTPTR(const void *, gd->fdt_blob);
+	int phandle;
+	int smi_offset;
+	int gpio_offset;
+	u64 smi_addr = 0;
+	int len;
+	u32 *pgpio_handle;
+	int gpio_count = 0;
+	u32 *prop_val;
+	int offset;
+	const char *prop_name;
+
+	debug("%s(%p, 0x%x, 0x%x)\n", __func__, phy_info, mdio_offset,
+	      mux_offset);
+
+	/* Get register value to put onto the GPIO lines to select */
+	phy_info->gpio_value =
+		cvmx_fdt_get_int(fdt_addr, mdio_offset, "reg", -1);
+	if (phy_info->gpio_value < 0) {
+		debug("Could not get register value for muxed MDIO bus from DT\n");
+		return -1;
+	}
+
+	smi_offset = cvmx_fdt_lookup_phandle(fdt_addr, mux_offset,
+					     "mdio-parent-bus");
+	if (smi_offset < 0) {
+		debug("Invalid SMI offset for muxed MDIO interface in device tree\n");
+		return -1;
+	}
+	smi_addr = cvmx_fdt_get_uint64(fdt_addr, smi_offset, "reg", 0);
+
+	/* Convert SMI address to a MDIO interface */
+	switch (smi_addr) {
+	case 0x1180000001800:
+	case 0x1180000003800: /* 68XX address */
+		phy_info->mdio_unit = 0;
+		break;
+	case 0x1180000001900:
+	case 0x1180000003880:
+		phy_info->mdio_unit = 1;
+		break;
+	case 0x1180000003900:
+		phy_info->mdio_unit = 2;
+		break;
+	case 0x1180000003980:
+		phy_info->mdio_unit = 3;
+		break;
+	default:
+		phy_info->mdio_unit = 1;
+		break;
+	}
+	/* Find the GPIO MUX controller */
+	pgpio_handle =
+		(u32 *)fdt_getprop(fdt_addr, mux_offset, "gpios", &len);
+	if (!pgpio_handle || len < 12 || (len % 12) != 0 ||
+	    len > CVMX_PHY_MUX_MAX_GPIO * 12) {
+		debug("Invalid GPIO for muxed MDIO controller in DT\n");
+		return -1;
+	}
+
+	for (gpio_count = 0; gpio_count < len / 12; gpio_count++) {
+		phandle = fdt32_to_cpu(pgpio_handle[gpio_count * 3]);
+		phy_info->gpio[gpio_count] =
+			fdt32_to_cpu(pgpio_handle[gpio_count * 3 + 1]);
+		gpio_offset = fdt_node_offset_by_phandle(fdt_addr, phandle);
+		if (gpio_offset < 0) {
+			debug("Cannot access parent GPIO node in DT\n");
+			return -1;
+		}
+		if (!fdt_node_check_compatible(fdt_addr, gpio_offset,
+					       "cavium,octeon-3860-gpio")) {
+			phy_info->gpio_type[gpio_count] = GPIO_OCTEON;
+		} else if (!fdt_node_check_compatible(fdt_addr, gpio_offset,
+						      "nxp,pca8574")) {
+			/* GPIO is a TWSI GPIO unit which might sit behind
+			 * another mux.
+			 */
+			phy_info->gpio_type[gpio_count] = GPIO_PCA8574;
+			prop_val = (u32 *)fdt_getprop(
+				fdt_addr, gpio_offset, "reg", NULL);
+			if (!prop_val) {
+				debug("Could not find TWSI address of npx pca8574 GPIO from DT\n");
+				return -1;
+			}
+			/* Get the TWSI address of the GPIO unit */
+			phy_info->cvmx_gpio_twsi[gpio_count] =
+				fdt32_to_cpu(*prop_val);
+			/* Get the selector on the GPIO mux if present */
+			offset = fdt_parent_offset(fdt_addr, gpio_offset);
+			prop_val = (u32 *)fdt_getprop(fdt_addr, offset,
+							   "reg", NULL);
+			if (prop_val) {
+				phy_info->gpio_parent_mux_select =
+					fdt32_to_cpu(*prop_val);
+				/* Go up another level */
+				offset = fdt_parent_offset(fdt_addr, offset);
+				if (!fdt_node_check_compatible(fdt_addr, offset,
+							       "nxp,pca9548")) {
+					prop_val = (u32 *)fdt_getprop(
+						fdt_addr, offset, "reg", NULL);
+					if (!prop_val) {
+						debug("Could not read MUX TWSI address from DT\n");
+						return -1;
+					}
+					phy_info->gpio_parent_mux_twsi =
+						fdt32_to_cpu(*prop_val);
+				}
+			}
+		} else {
+			prop_name = (char *)fdt_getprop(fdt_addr, gpio_offset,
+							"compatible", NULL);
+			debug("Unknown GPIO type %s\n", prop_name);
+			return -1;
+		}
+	}
+	return 0;
+}
+
+/**
+ * @INTERNAL
+ * Converts a BGX address to the node, interface and port number
+ *
+ * @param bgx_addr	Address of CSR register
+ *
+ * @return node, interface and port number, will be -1 for invalid address.
+ */
+static struct cvmx_xiface __cvmx_bgx_reg_addr_to_xiface(u64 bgx_addr)
+{
+	struct cvmx_xiface xi = { -1, -1 };
+
+	xi.node = cvmx_csr_addr_to_node(bgx_addr);
+	bgx_addr = cvmx_csr_addr_strip_node(bgx_addr);
+	if ((bgx_addr & 0xFFFFFFFFF0000000) != 0x00011800E0000000) {
+		debug("%s: Invalid BGX address 0x%llx\n", __func__,
+		      (unsigned long long)bgx_addr);
+		xi.node = -1;
+		return xi;
+	}
+	xi.interface = (bgx_addr >> 24) & 0x0F;
+
+	return xi;
+}
+
+static cvmx_helper_link_info_t
+__get_marvell_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+	int phy_status;
+	u32 phy_addr = phy_info->phy_addr;
+
+	result.u64 = 0;
+	/* Set to page 0 */
+	cvmx_mdio_write(phy_addr >> 8, phy_addr & 0xff, 22, 0);
+	/* All the speed information can be read from register 17 in one go. */
+	phy_status = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 17);
+
+	/* If the resolve bit 11 isn't set, see if autoneg is turned off
+	 * (bit 12, reg 0). The resolve bit doesn't get set properly when
+	 * autoneg is off, so force it
+	 */
+	if ((phy_status & (1 << 11)) == 0) {
+		int auto_status =
+			cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0);
+		if ((auto_status & (1 << 12)) == 0)
+			phy_status |= 1 << 11;
+	}
+
+	/* Link is up = Speed/Duplex Resolved + RT-Link Up + G-Link Up. */
+	if ((phy_status & 0x0c08) == 0x0c08) {
+		result.s.link_up = 1;
+		result.s.full_duplex = ((phy_status >> 13) & 1);
+		switch ((phy_status >> 14) & 3) {
+		case 0: /* 10 Mbps */
+			result.s.speed = 10;
+			break;
+		case 1: /* 100 Mbps */
+			result.s.speed = 100;
+			break;
+		case 2: /* 1 Gbps */
+			result.s.speed = 1000;
+			break;
+		case 3: /* Illegal */
+			result.u64 = 0;
+			break;
+		}
+	}
+	return result;
+}
+
+/**
+ * @INTERNAL
+ * Get link state of broadcom PHY
+ *
+ * @param phy_info	PHY information
+ */
+static cvmx_helper_link_info_t
+__get_broadcom_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+	u32 phy_addr = phy_info->phy_addr;
+	int phy_status;
+
+	result.u64 = 0;
+	/* Below we are going to read SMI/MDIO register 0x19 which works
+	 * on Broadcom parts
+	 */
+	phy_status = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0x19);
+	switch ((phy_status >> 8) & 0x7) {
+	case 0:
+		result.u64 = 0;
+		break;
+	case 1:
+		result.s.link_up = 1;
+		result.s.full_duplex = 0;
+		result.s.speed = 10;
+		break;
+	case 2:
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 10;
+		break;
+	case 3:
+		result.s.link_up = 1;
+		result.s.full_duplex = 0;
+		result.s.speed = 100;
+		break;
+	case 4:
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 100;
+		break;
+	case 5:
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 100;
+		break;
+	case 6:
+		result.s.link_up = 1;
+		result.s.full_duplex = 0;
+		result.s.speed = 1000;
+		break;
+	case 7:
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 1000;
+		break;
+	}
+	return result;
+}
+
+/**
+ * @INTERNAL
+ * Get link state of generic gigabit PHY
+ *
+ * @param phy_info - information about the PHY
+ *
+ * @returns link status of the PHY
+ */
+static cvmx_helper_link_info_t
+__cvmx_get_generic_8023_c22_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+	u32 phy_addr = phy_info->phy_addr;
+	int phy_basic_control;	 /* Register 0x0 */
+	int phy_basic_status;	 /* Register 0x1 */
+	int phy_anog_adv;	 /* Register 0x4 */
+	int phy_link_part_avail; /* Register 0x5 */
+	int phy_control;	 /* Register 0x9 */
+	int phy_status;		 /* Register 0xA */
+
+	result.u64 = 0;
+
+	phy_basic_status = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 1);
+	if (!(phy_basic_status & 0x4)) /* Check if link is up */
+		return result;	       /* Link is down, return link down */
+
+	result.s.link_up = 1;
+	phy_basic_control = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0);
+	/* Check if autonegotiation is enabled and completed */
+	if ((phy_basic_control & (1 << 12)) && (phy_basic_status & (1 << 5))) {
+		phy_status =
+			cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0xA);
+		phy_control =
+			cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0x9);
+
+		phy_status &= phy_control << 2;
+		phy_link_part_avail =
+			cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0x5);
+		phy_anog_adv =
+			cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0x4);
+		phy_link_part_avail &= phy_anog_adv;
+
+		if (phy_status & 0xC00) { /* Gigabit full or half */
+			result.s.speed = 1000;
+			result.s.full_duplex = !!(phy_status & 0x800);
+		} else if (phy_link_part_avail &
+			   0x0180) { /* 100 full or half */
+			result.s.speed = 100;
+			result.s.full_duplex = !!(phy_link_part_avail & 0x100);
+		} else if (phy_link_part_avail & 0x0060) {
+			result.s.speed = 10;
+			result.s.full_duplex = !!(phy_link_part_avail & 0x0040);
+		}
+	} else {
+		/* Not autonegotiated */
+		result.s.full_duplex = !!(phy_basic_control & (1 << 8));
+
+		if (phy_basic_control & (1 << 6))
+			result.s.speed = 1000;
+		else if (phy_basic_control & (1 << 13))
+			result.s.speed = 100;
+		else
+			result.s.speed = 10;
+	}
+	return result;
+}
+
+static cvmx_helper_link_info_t
+__cvmx_get_qualcomm_s17_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+	u32 phy_addr = phy_info->phy_addr;
+	int phy_status;
+	int auto_status;
+
+	result.u64 = 0;
+
+	phy_status = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 17);
+
+	/* If bit 11 isn't set see if autonegotiation is turned off
+	 * (bit 12, reg 0).  The resolved bit doesn't get set properly when
+	 * autonegotiation is off, so force it.
+	 */
+	if ((phy_status & (1 << 11)) == 0) {
+		auto_status = cvmx_mdio_read(phy_addr >> 8, phy_addr & 0xff, 0);
+		if ((auto_status & (1 << 12)) == 0)
+			phy_status |= 1 << 11;
+	}
+	/* Only return a link if the PHY has finished autonegotiation and set
+	 * the resolved bit (bit 11).
+	 */
+	if (phy_status & (1 << 11)) {
+		result.s.link_up = 1;
+		result.s.full_duplex = !!(phy_status & (1 << 13));
+		switch ((phy_status >> 14) & 3) {
+		case 0: /* 10Mbps */
+			result.s.speed = 10;
+			break;
+		case 1: /* 100Mbps */
+			result.s.speed = 100;
+			break;
+		case 2: /* 1Gbps */
+			result.s.speed = 1000;
+			break;
+		default: /* Illegal */
+			result.u64 = 0;
+			break;
+		}
+	}
+	debug("   link: %s, duplex: %s, speed: %lu\n",
+	      result.s.link_up ? "up" : "down",
+	      result.s.full_duplex ? "full" : "half",
+	      (unsigned long)result.s.speed);
+	return result;
+}
+
+static cvmx_helper_link_info_t
+__get_generic_8023_c45_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+	int phy_status;
+	int pma_ctrl1;
+	u32 phy_addr = phy_info->phy_addr;
+
+	result.u64 = 0;
+	pma_ctrl1 = cvmx_mdio_45_read(phy_addr >> 8, phy_addr & 0xff, 1, 0);
+	if ((pma_ctrl1 & 0x207c) == 0x2040)
+		result.s.speed = 10000;
+	/* PMA Status 1 (1x0001) */
+	phy_status = cvmx_mdio_45_read(phy_addr >> 8, phy_addr & 0xff, 1, 0xa);
+	if (phy_status < 0)
+		return result;
+
+	result.s.full_duplex = 1;
+	if ((phy_status & 1) == 0)
+		return result;
+	phy_status = cvmx_mdio_45_read(phy_addr >> 8, phy_addr & 0xff, 4, 0x18);
+	if (phy_status < 0)
+		return result;
+	result.s.link_up = (phy_status & 0x1000) ? 1 : 0;
+
+	return result;
+}
+
+static cvmx_helper_link_info_t
+__cvmx_get_cortina_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+
+	result.s.link_up = 1;
+	result.s.full_duplex = 1;
+	result.s.speed = 1000;
+	return result;
+}
+
+static cvmx_helper_link_info_t
+__get_vitesse_vsc8490_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+
+	result.s.link_up = 1;
+	result.s.full_duplex = 1;
+	result.s.speed = 1000;
+	return result;
+}
+
+static cvmx_helper_link_info_t
+__get_aquantia_phy_link_state(cvmx_phy_info_t *phy_info)
+{
+	cvmx_helper_link_info_t result;
+
+	result.s.link_up = 1;
+	result.s.full_duplex = 1;
+	result.s.speed = 1000;
+	return result;
+}
+
+static int __cvmx_helper_78xx_parse_phy(struct cvmx_phy_info *phy_info,
+					int ipd_port)
+{
+	const void *fdt_addr = CASTPTR(const void *, gd->fdt_blob);
+	const char *compat;
+	int phy;
+	int parent;
+	u64 mdio_base;
+	int node, bus;
+	int phy_addr;
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	int xiface = cvmx_helper_get_interface_num(ipd_port);
+	int compat_len = 0;
+
+	debug("%s(0x%p, %d) ENTER\n", __func__, phy_info, ipd_port);
+
+	phy = cvmx_helper_get_phy_fdt_node_offset(xiface, index);
+	debug("%s: xiface: 0x%x, index: %d, ipd_port: %d, phy fdt offset: %d\n",
+	      __func__, xiface, index, ipd_port, phy);
+	if (phy < 0) {
+		/* If this is the first time through we need to first parse the
+		 * device tree to get the node offsets.
+		 */
+		debug("No config present, calling __cvmx_helper_parse_bgx_dt\n");
+		if (__cvmx_helper_parse_bgx_dt(fdt_addr)) {
+			printf("Error: could not parse BGX device tree\n");
+			return -1;
+		}
+		if (__cvmx_fdt_parse_vsc7224(fdt_addr)) {
+			debug("Error: could not parse Microsemi VSC7224 in DT\n");
+			return -1;
+		}
+		if (octeon_has_feature(OCTEON_FEATURE_BGX_XCV) &&
+		    __cvmx_helper_parse_bgx_rgmii_dt(fdt_addr)) {
+			printf("Error: could not parse BGX XCV device tree\n");
+			return -1;
+		}
+		phy = cvmx_helper_get_phy_fdt_node_offset(xiface, index);
+		if (phy < 0) {
+			debug("%s: Could not get PHY node offset for IPD port 0x%x, xiface: 0x%x, index: %d\n",
+			      __func__, ipd_port, xiface, index);
+			return -1;
+		}
+		debug("%s: phy: %d (%s)\n", __func__, phy,
+		      fdt_get_name(fdt_addr, phy, NULL));
+	}
+
+	compat = (const char *)fdt_getprop(fdt_addr, phy, "compatible",
+					   &compat_len);
+	if (!compat) {
+		printf("ERROR: %d:%d:no compatible prop in phy\n", xiface,
+		       index);
+		return -1;
+	}
+
+	debug("  compatible: %s\n", compat);
+
+	phy_info->fdt_offset = phy;
+	phy_addr = cvmx_fdt_get_int(fdt_addr, phy, "reg", -1);
+	if (phy_addr == -1) {
+		printf("Error: %d:%d:could not get PHY address\n", xiface,
+		       index);
+		return -1;
+	}
+	debug("  PHY address: %d, compat: %s\n", phy_addr, compat);
+
+	if (!memcmp("marvell", compat, strlen("marvell"))) {
+		phy_info->phy_type = MARVELL_GENERIC_PHY;
+		phy_info->link_function = __get_marvell_phy_link_state;
+	} else if (!memcmp("broadcom", compat, strlen("broadcom"))) {
+		phy_info->phy_type = BROADCOM_GENERIC_PHY;
+		phy_info->link_function = __get_broadcom_phy_link_state;
+	} else if (!memcmp("cortina", compat, strlen("cortina"))) {
+		phy_info->phy_type = CORTINA_PHY;
+		phy_info->link_function = __cvmx_get_cortina_phy_link_state;
+	} else if (!strcmp("vitesse,vsc8490", compat)) {
+		phy_info->phy_type = VITESSE_VSC8490_PHY;
+		phy_info->link_function = __get_vitesse_vsc8490_phy_link_state;
+	} else if (fdt_stringlist_contains(compat, compat_len,
+					   "ethernet-phy-ieee802.3-c22")) {
+		phy_info->phy_type = GENERIC_8023_C22_PHY;
+		phy_info->link_function =
+			__cvmx_get_generic_8023_c22_phy_link_state;
+	} else if (fdt_stringlist_contains(compat, compat_len,
+					   "ethernet-phy-ieee802.3-c45")) {
+		phy_info->phy_type = GENERIC_8023_C22_PHY;
+		phy_info->link_function = __get_generic_8023_c45_phy_link_state;
+	}
+
+	phy_info->ipd_port = ipd_port;
+	phy_info->phy_sub_addr = 0;
+	phy_info->direct_connect = 1;
+
+	parent = fdt_parent_offset(fdt_addr, phy);
+	if (!fdt_node_check_compatible(fdt_addr, parent,
+				       "ethernet-phy-nexus")) {
+		debug("  nexus PHY found\n");
+		if (phy_info->phy_type == CORTINA_PHY) {
+			/* The Cortina CS422X uses the same PHY device for
+			 * multiple ports for XFI.  In this case we use a
+			 * nexus and each PHY address is the slice or
+			 * sub-address and the actual PHY address is the
+			 * nexus address.
+			 */
+			phy_info->phy_sub_addr = phy_addr;
+			phy_addr =
+				cvmx_fdt_get_int(fdt_addr, parent, "reg", -1);
+			debug("  Cortina PHY real address: 0x%x\n", phy_addr);
+		}
+		parent = fdt_parent_offset(fdt_addr, parent);
+	}
+
+	debug("  Parent: %s\n", fdt_get_name(fdt_addr, parent, NULL));
+	if (!fdt_node_check_compatible(fdt_addr, parent,
+				       "cavium,octeon-3860-mdio")) {
+		debug("  Found Octeon MDIO\n");
+		mdio_base = cvmx_fdt_get_uint64(fdt_addr, parent, "reg",
+						FDT_ADDR_T_NONE);
+		debug("  MDIO address: 0x%llx\n",
+		      (unsigned long long)mdio_base);
+
+		mdio_base = cvmx_fdt_translate_address(fdt_addr, parent,
+						       (u32 *)&mdio_base);
+		debug("  Translated: 0x%llx\n", (unsigned long long)mdio_base);
+		if (mdio_base == FDT_ADDR_T_NONE) {
+			printf("Could not get MDIO base address from reg field\n");
+			return -1;
+		}
+		__cvmx_mdio_addr_to_node_bus(mdio_base, &node, &bus);
+		if (bus < 0) {
+			printf("Invalid MDIO address 0x%llx, could not detect bus and node\n",
+			       (unsigned long long)mdio_base);
+			return -1;
+		}
+		debug("  MDIO node: %d, bus: %d\n", node, bus);
+		phy_info->mdio_unit = (node << 2) | (bus & 3);
+		phy_info->phy_addr = phy_addr | (phy_info->mdio_unit << 8);
+	} else {
+		printf("%s: Error: incompatible MDIO bus %s for IPD port %d\n",
+		       __func__,
+		       (const char *)fdt_get_name(fdt_addr, parent, NULL),
+		       ipd_port);
+		return -1;
+	}
+
+	debug("%s: EXIT 0\n", __func__);
+
+	return 0;
+}
+
+/**
+ * Return the MII PHY address associated with the given IPD
+ * port. The phy address is obtained from the device tree.
+ *
+ * @param[out] phy_info - PHY information data structure updated
+ * @param ipd_port Octeon IPD port to get the MII address for.
+ *
+ * @return MII PHY address and bus number, -1 on error, -2 if PHY info missing (OK).
+ */
+static int __get_phy_info_from_dt(cvmx_phy_info_t *phy_info, int ipd_port)
+{
+	const void *fdt_addr = CASTPTR(const void *, gd->fdt_blob);
+	int aliases, eth, phy, phy_parent, ret, i;
+	int mdio_parent;
+	const char *phy_compatible_str;
+	const char *host_mode_str = NULL;
+	int interface;
+	int phy_addr_offset = 0;
+
+	debug("%s(%p, %d)\n", __func__, phy_info, ipd_port);
+
+	if (octeon_has_feature(OCTEON_FEATURE_BGX))
+		return __cvmx_helper_78xx_parse_phy(phy_info, ipd_port);
+
+	phy_info->phy_addr = -1;
+	phy_info->phy_sub_addr = 0;
+	phy_info->ipd_port = ipd_port;
+	phy_info->direct_connect = -1;
+	phy_info->phy_type = (cvmx_phy_type_t)-1;
+	for (i = 0; i < CVMX_PHY_MUX_MAX_GPIO; i++)
+		phy_info->gpio[i] = -1;
+	phy_info->mdio_unit = -1;
+	phy_info->gpio_value = -1;
+	phy_info->gpio_parent_mux_twsi = -1;
+	phy_info->gpio_parent_mux_select = -1;
+	phy_info->link_function = NULL;
+	phy_info->fdt_offset = -1;
+	if (!fdt_addr) {
+		debug("No device tree found.\n");
+		return -1;
+	}
+
+	aliases = fdt_path_offset(fdt_addr, "/aliases");
+	if (aliases < 0) {
+		debug("Error: No /aliases node in device tree.\n");
+		return -1;
+	}
+	if (ipd_port < 0) {
+		int interface_index =
+			ipd_port - CVMX_HELPER_BOARD_MGMT_IPD_PORT;
+		eth = __mix_eth_node(fdt_addr, aliases, interface_index);
+	} else {
+		eth = __pip_eth_node(fdt_addr, aliases, ipd_port);
+	}
+	if (eth < 0) {
+		debug("ERROR : cannot find interface for ipd_port=%d\n",
+		      ipd_port);
+		return -1;
+	}
+
+	interface = cvmx_helper_get_interface_num(ipd_port);
+	/* Get handle to phy */
+	phy = cvmx_fdt_lookup_phandle(fdt_addr, eth, "phy-handle");
+	if (phy < 0) {
+		cvmx_helper_interface_mode_t if_mode;
+
+		/* Note that it's OK for RXAUI and ILK to not have a PHY
+		 * connected (i.e. EBB boards in loopback).
+		 */
+		debug("Cannot get phy-handle for ipd_port: %d\n", ipd_port);
+		if_mode = cvmx_helper_interface_get_mode(interface);
+		if (if_mode != CVMX_HELPER_INTERFACE_MODE_RXAUI &&
+		    if_mode != CVMX_HELPER_INTERFACE_MODE_ILK) {
+			debug("ERROR : phy handle not found in device tree ipd_port=%d\n",
+			      ipd_port);
+			return -1;
+		} else {
+			return -2;
+		}
+	}
+
+	phy_compatible_str =
+		(const char *)fdt_getprop(fdt_addr, phy, "compatible", NULL);
+	if (!phy_compatible_str) {
+		debug("ERROR: no compatible prop in phy\n");
+		return -1;
+	}
+	debug("Checking compatible string \"%s\" for ipd port %d\n",
+	      phy_compatible_str, ipd_port);
+	phy_info->fdt_offset = phy;
+	if (!memcmp("marvell", phy_compatible_str, strlen("marvell"))) {
+		debug("Marvell PHY detected for ipd_port %d\n", ipd_port);
+		phy_info->phy_type = MARVELL_GENERIC_PHY;
+		phy_info->link_function = __get_marvell_phy_link_state;
+	} else if (!memcmp("broadcom", phy_compatible_str,
+			   strlen("broadcom"))) {
+		phy_info->phy_type = BROADCOM_GENERIC_PHY;
+		phy_info->link_function = __get_broadcom_phy_link_state;
+		debug("Broadcom PHY detected for ipd_port %d\n", ipd_port);
+	} else if (!memcmp("vitesse", phy_compatible_str, strlen("vitesse"))) {
+		debug("Vitesse PHY detected for ipd_port %d\n", ipd_port);
+		if (!fdt_node_check_compatible(fdt_addr, phy,
+					       "vitesse,vsc8490")) {
+			phy_info->phy_type = VITESSE_VSC8490_PHY;
+			debug("Vitesse VSC8490 detected\n");
+			phy_info->link_function =
+				__get_vitesse_vsc8490_phy_link_state;
+		} else if (!fdt_node_check_compatible(
+				   fdt_addr, phy,
+				   "ethernet-phy-ieee802.3-c22")) {
+			phy_info->phy_type = GENERIC_8023_C22_PHY;
+			phy_info->link_function =
+				__cvmx_get_generic_8023_c22_phy_link_state;
+			debug("Vitesse 802.3 c22 detected\n");
+		} else {
+			phy_info->phy_type = GENERIC_8023_C45_PHY;
+			phy_info->link_function =
+				__get_generic_8023_c45_phy_link_state;
+			debug("Vitesse 802.3 c45 detected\n");
+		}
+	} else if (!memcmp("aquantia", phy_compatible_str,
+			   strlen("aquantia"))) {
+		phy_info->phy_type = AQUANTIA_PHY;
+		phy_info->link_function = __get_aquantia_phy_link_state;
+		debug("Aquantia c45 PHY detected\n");
+	} else if (!memcmp("cortina", phy_compatible_str, strlen("cortina"))) {
+		phy_info->phy_type = CORTINA_PHY;
+		phy_info->link_function = __cvmx_get_cortina_phy_link_state;
+		host_mode_str = (const char *)fdt_getprop(
+			fdt_addr, phy, "cortina,host-mode", NULL);
+		debug("Cortina PHY detected for ipd_port %d\n", ipd_port);
+	} else if (!memcmp("ti", phy_compatible_str, strlen("ti"))) {
+		phy_info->phy_type = GENERIC_8023_C45_PHY;
+		phy_info->link_function = __get_generic_8023_c45_phy_link_state;
+		debug("TI PHY detected for ipd_port %d\n", ipd_port);
+	} else if (!fdt_node_check_compatible(fdt_addr, phy,
+					      "atheros,ar8334") ||
+		   !fdt_node_check_compatible(fdt_addr, phy,
+					      "qualcomm,qca8334") ||
+		   !fdt_node_check_compatible(fdt_addr, phy,
+					      "atheros,ar8337") ||
+		   !fdt_node_check_compatible(fdt_addr, phy,
+					      "qualcomm,qca8337")) {
+		phy_info->phy_type = QUALCOMM_S17;
+		phy_info->link_function =
+			__cvmx_get_qualcomm_s17_phy_link_state;
+		debug("Qualcomm QCA833X switch detected\n");
+	} else if (!fdt_node_check_compatible(fdt_addr, phy,
+					      "ethernet-phy-ieee802.3-c22")) {
+		phy_info->phy_type = GENERIC_8023_C22_PHY;
+		phy_info->link_function =
+			__cvmx_get_generic_8023_c22_phy_link_state;
+		debug("Generic 802.3 c22 PHY detected\n");
+	} else if (!fdt_node_check_compatible(fdt_addr, phy,
+					      "ethernet-phy-ieee802.3-c45")) {
+		phy_info->phy_type = GENERIC_8023_C45_PHY;
+		phy_info->link_function = __get_generic_8023_c45_phy_link_state;
+		debug("Generic 802.3 c45 PHY detected\n");
+	} else {
+		debug("Unknown PHY compatibility\n");
+		phy_info->phy_type = (cvmx_phy_type_t)-1;
+		phy_info->link_function = NULL;
+	}
+
+	phy_info->host_mode = CVMX_PHY_HOST_MODE_UNKNOWN;
+	if (host_mode_str) {
+		if (strcmp(host_mode_str, "rxaui") == 0)
+			phy_info->host_mode = CVMX_PHY_HOST_MODE_RXAUI;
+		else if (strcmp(host_mode_str, "xaui") == 0)
+			phy_info->host_mode = CVMX_PHY_HOST_MODE_XAUI;
+		else if (strcmp(host_mode_str, "sgmii") == 0)
+			phy_info->host_mode = CVMX_PHY_HOST_MODE_SGMII;
+		else if (strcmp(host_mode_str, "qsgmii") == 0)
+			phy_info->host_mode = CVMX_PHY_HOST_MODE_QSGMII;
+		else
+			debug("Unknown PHY host mode\n");
+	}
+
+	/* Check if PHY parent is the octeon MDIO bus. Some boards are connected
+	 * though a MUX and for them direct_connect_to_phy will be 0
+	 */
+	phy_parent = fdt_parent_offset(fdt_addr, phy);
+	if (phy_parent < 0) {
+		debug("ERROR : cannot find phy parent for ipd_port=%d ret=%d\n",
+		      ipd_port, phy_parent);
+		return -1;
+	}
+	/* For multi-phy devices and devices on a MUX, go to the parent */
+	ret = fdt_node_check_compatible(fdt_addr, phy_parent,
+					"ethernet-phy-nexus");
+	if (ret == 0) {
+		/* It's a nexus so check the grandparent. */
+		phy_addr_offset =
+			cvmx_fdt_get_int(fdt_addr, phy_parent, "reg", 0);
+		phy_parent = fdt_parent_offset(fdt_addr, phy_parent);
+	}
+
+	/* Check for a muxed MDIO interface */
+	mdio_parent = fdt_parent_offset(fdt_addr, phy_parent);
+	ret = fdt_node_check_compatible(fdt_addr, mdio_parent,
+					"cavium,mdio-mux");
+	if (ret == 0) {
+		ret = __get_muxed_mdio_info_from_dt(phy_info, phy_parent,
+						    mdio_parent);
+		if (ret) {
+			printf("Error reading mdio mux information for ipd port %d\n",
+			       ipd_port);
+			return -1;
+		}
+	}
+	ret = fdt_node_check_compatible(fdt_addr, phy_parent,
+					"cavium,octeon-3860-mdio");
+	if (ret == 0) {
+		u32 *mdio_reg_base =
+			(u32 *)fdt_getprop(fdt_addr, phy_parent, "reg", 0);
+		phy_info->direct_connect = 1;
+		if (mdio_reg_base == 0) {
+			debug("ERROR : unable to get reg property in phy mdio\n");
+			return -1;
+		}
+		phy_info->mdio_unit =
+			__mdiobus_addr_to_unit(fdt32_to_cpu(mdio_reg_base[1]));
+		debug("phy parent=%s reg_base=%08x mdio_unit=%d\n",
+		      fdt_get_name(fdt_addr, phy_parent, NULL),
+		      (int)mdio_reg_base[1], phy_info->mdio_unit);
+	} else {
+		phy_info->direct_connect = 0;
+		/* The PHY is not directly connected to the Octeon MDIO bus.
+		 * SE doesn't  have abstractions for MDIO MUX or MDIO MUX
+		 * drivers and hence for the non direct cases code will be
+		 * needed which is board specific.
+		 * For now the MDIO Unit is defaulted to 1.
+		 */
+		debug("%s PHY at address: %d is not directly connected\n",
+		      __func__, phy_info->phy_addr);
+	}
+
+	phy_info->phy_addr = cvmx_fdt_get_int(fdt_addr, phy, "reg", -1);
+	if (phy_info->phy_addr < 0) {
+		debug("ERROR: Could not read phy address from reg in DT\n");
+		return -1;
+	}
+	phy_info->phy_addr += phy_addr_offset;
+	phy_info->phy_addr |= phy_info->mdio_unit << 8;
+	debug("%s(%p, %d) => 0x%x\n", __func__, phy_info, ipd_port,
+	      phy_info->phy_addr);
+	return phy_info->phy_addr;
+}
+
+/**
+ * @INTERNAL
+ * This function outputs the cvmx_phy_info_t data structure for the specified
+ * port.
+ *
+ * @param phy_info - phy info data structure
+ * @param ipd_port - port to get phy info for
+ *
+ * @return 0 for success, -1 if info not available
+ *
+ * NOTE: The phy_info data structure is subject to change.
+ */
+int cvmx_helper_board_get_phy_info(cvmx_phy_info_t *phy_info, int ipd_port)
+{
+	int retcode;
+
+	retcode = __get_phy_info_from_dt(phy_info, ipd_port);
+
+	return (retcode >= 0) ? 0 : -1;
+}
+
+/**
+ * Return the MII PHY address associated with the given IPD
+ * port. The phy address is obtained from the device tree.
+ *
+ * @param ipd_port Octeon IPD port to get the MII address for.
+ *
+ * @return MII PHY address and bus number or -1 on error, -2 if phy info missing (OK).
+ */
+int cvmx_helper_board_get_mii_address_from_dt(int ipd_port)
+{
+	cvmx_phy_info_t phy_info;
+	int retcode = __get_phy_info_from_dt(&phy_info, ipd_port);
+
+	if (retcode >= 0)
+		return phy_info.phy_addr;
+	else
+		return retcode;
+}
+
+/**
+ * Return the MII PHY address associated with the given IPD
+ * port. A result of -1 means there isn't a MII capable PHY
+ * connected to this port. On chips supporting multiple MII
+ * busses the bus number is encoded in bits <15:8>.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It replies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @param ipd_port Octeon IPD port to get the MII address for.
+ *
+ * @return MII PHY address and bus number or -1.
+ */
+int cvmx_helper_board_get_mii_address(int ipd_port)
+{
+	cvmx_phy_info_t phy_info;
+	int retcode;
+
+	debug("%s(0x%x) getting phy info from device tree\n", __func__,
+	      ipd_port);
+	memset(&phy_info, 0, sizeof(phy_info));
+	retcode = __get_phy_info_from_dt(&phy_info, ipd_port);
+
+	if (retcode == -2) {
+		debug("%s(0x%x): phy info missing in device tree\n", __func__,
+		      ipd_port);
+		return retcode;
+	} else if (retcode < 0) {
+		debug("%s: could not get phy info for port %d\n", __func__,
+		      ipd_port);
+		return retcode;
+	}
+	debug("%s: phy address: 0x%x\n", __func__, phy_info.phy_addr);
+
+	/* Some unknown board. Somebody forgot to update this function... */
+	debug("%s: Unknown board type\n", __func__);
+	return -1;
+}
+
+/**
+ * @INTERNAL
+ * Parse the device tree and set whether a port is valid or not.
+ *
+ * @param fdt_addr	Pointer to device tree
+ *
+ * @return 0 for success, -1 on error.
+ */
+int __cvmx_helper_parse_bgx_dt(const void *fdt_addr)
+{
+	int port_index;
+	struct cvmx_xiface xi;
+	int fdt_port_node = -1;
+	int fdt_interface_node;
+	int fdt_phy_node;
+	u64 reg_addr;
+	int xiface;
+	struct cvmx_phy_info *phy_info;
+	static bool parsed;
+	int err;
+	int ipd_port;
+
+	if (parsed) {
+		debug("%s: Already parsed\n", __func__);
+		return 0;
+	}
+	while ((fdt_port_node = fdt_node_offset_by_compatible(
+			fdt_addr, fdt_port_node,
+			"cavium,octeon-7890-bgx-port")) >= 0) {
+		/* Get the port number */
+		port_index =
+			cvmx_fdt_get_int(fdt_addr, fdt_port_node, "reg", -1);
+		if (port_index < 0) {
+			debug("Error: missing reg field for bgx port in device tree\n");
+			return -1;
+		}
+		debug("%s: Parsing BGX port %d\n", __func__, port_index);
+		/* Get the interface number */
+		fdt_interface_node = fdt_parent_offset(fdt_addr, fdt_port_node);
+		if (fdt_interface_node < 0) {
+			debug("Error: device tree corrupt!\n");
+			return -1;
+		}
+		if (fdt_node_check_compatible(fdt_addr, fdt_interface_node,
+					      "cavium,octeon-7890-bgx")) {
+			debug("Error: incompatible Ethernet MAC Nexus in device tree!\n");
+			return -1;
+		}
+		reg_addr =
+			cvmx_fdt_get_addr(fdt_addr, fdt_interface_node, "reg");
+		debug("%s: BGX interface address: 0x%llx\n", __func__,
+		      (unsigned long long)reg_addr);
+		if (reg_addr == FDT_ADDR_T_NONE) {
+			debug("Device tree BGX node has invalid address 0x%llx\n",
+			      (unsigned long long)reg_addr);
+			return -1;
+		}
+		reg_addr = cvmx_fdt_translate_address(fdt_addr,
+						      fdt_interface_node,
+						      (u32 *)&reg_addr);
+		xi = __cvmx_bgx_reg_addr_to_xiface(reg_addr);
+		if (xi.node < 0) {
+			debug("Device tree BGX node has invalid address 0x%llx\n",
+			      (unsigned long long)reg_addr);
+			return -1;
+		}
+		debug("%s: Found BGX node %d, interface %d\n", __func__,
+		      xi.node, xi.interface);
+		xiface = cvmx_helper_node_interface_to_xiface(xi.node,
+							      xi.interface);
+		cvmx_helper_set_port_fdt_node_offset(xiface, port_index,
+						     fdt_port_node);
+		cvmx_helper_set_port_valid(xiface, port_index, true);
+
+		cvmx_helper_set_port_fdt_node_offset(xiface, port_index,
+						     fdt_port_node);
+		if (fdt_getprop(fdt_addr, fdt_port_node,
+				"cavium,sgmii-mac-phy-mode", NULL))
+			cvmx_helper_set_mac_phy_mode(xiface, port_index, true);
+		else
+			cvmx_helper_set_mac_phy_mode(xiface, port_index, false);
+
+		if (fdt_getprop(fdt_addr, fdt_port_node, "cavium,force-link-up",
+				NULL))
+			cvmx_helper_set_port_force_link_up(xiface, port_index,
+							   true);
+		else
+			cvmx_helper_set_port_force_link_up(xiface, port_index,
+							   false);
+
+		if (fdt_getprop(fdt_addr, fdt_port_node,
+				"cavium,sgmii-mac-1000x-mode", NULL))
+			cvmx_helper_set_1000x_mode(xiface, port_index, true);
+		else
+			cvmx_helper_set_1000x_mode(xiface, port_index, false);
+
+		if (fdt_getprop(fdt_addr, fdt_port_node,
+				"cavium,disable-autonegotiation", NULL))
+			cvmx_helper_set_port_autonegotiation(xiface, port_index,
+							     false);
+		else
+			cvmx_helper_set_port_autonegotiation(xiface, port_index,
+							     true);
+
+		fdt_phy_node = cvmx_fdt_lookup_phandle(fdt_addr, fdt_port_node,
+						       "phy-handle");
+		if (fdt_phy_node >= 0) {
+			cvmx_helper_set_phy_fdt_node_offset(xiface, port_index,
+							    fdt_phy_node);
+			debug("%s: Setting PHY fdt node offset for interface 0x%x, port %d to %d\n",
+			      __func__, xiface, port_index, fdt_phy_node);
+			debug("%s: PHY node name: %s\n", __func__,
+			      fdt_get_name(fdt_addr, fdt_phy_node, NULL));
+			cvmx_helper_set_port_phy_present(xiface, port_index,
+							 true);
+			ipd_port = cvmx_helper_get_ipd_port(xiface, port_index);
+			if (ipd_port >= 0) {
+				debug("%s: Allocating phy info for 0x%x:%d\n",
+				      __func__, xiface, port_index);
+				phy_info =
+					(cvmx_phy_info_t *)cvmx_bootmem_alloc(
+						sizeof(*phy_info), 0);
+				if (!phy_info) {
+					debug("%s: Out of memory\n", __func__);
+					return -1;
+				}
+				memset(phy_info, 0, sizeof(*phy_info));
+				phy_info->phy_addr = -1;
+				err = __get_phy_info_from_dt(phy_info,
+							     ipd_port);
+				if (err) {
+					debug("%s: Error parsing phy info for ipd port %d\n",
+					      __func__, ipd_port);
+					return -1;
+				}
+				cvmx_helper_set_port_phy_info(
+					xiface, port_index, phy_info);
+				debug("%s: Saved phy info\n", __func__);
+			}
+		} else {
+			cvmx_helper_set_phy_fdt_node_offset(xiface, port_index,
+							    -1);
+			debug("%s: No PHY fdt node offset for interface 0x%x, port %d to %d\n",
+			      __func__, xiface, port_index, fdt_phy_node);
+			cvmx_helper_set_port_phy_present(xiface, port_index,
+							 false);
+		}
+	}
+	if (!sfp_parsed)
+		if (cvmx_sfp_parse_device_tree(fdt_addr))
+			debug("%s: Error parsing SFP device tree\n", __func__);
+	parsed = true;
+	return 0;
+}
+
+int __cvmx_helper_parse_bgx_rgmii_dt(const void *fdt_addr)
+{
+	u64 reg_addr;
+	struct cvmx_xiface xi;
+	int fdt_port_node = -1;
+	int fdt_interface_node;
+	int fdt_phy_node;
+	int port_index;
+	int xiface;
+
+	/* There's only one xcv (RGMII) interface, so just search for the one
+	 * that's part of a BGX entry.
+	 */
+	while ((fdt_port_node = fdt_node_offset_by_compatible(
+			fdt_addr, fdt_port_node, "cavium,octeon-7360-xcv")) >=
+	       0) {
+		fdt_interface_node = fdt_parent_offset(fdt_addr, fdt_port_node);
+		if (fdt_interface_node < 0) {
+			printf("Error: device tree corrupt!\n");
+			return -1;
+		}
+		debug("%s: XCV parent node compatible: %s\n", __func__,
+		      (char *)fdt_getprop(fdt_addr, fdt_interface_node,
+					  "compatible", NULL));
+		if (!fdt_node_check_compatible(fdt_addr, fdt_interface_node,
+					       "cavium,octeon-7890-bgx"))
+			break;
+	}
+	if (fdt_port_node == -FDT_ERR_NOTFOUND) {
+		debug("No XCV/RGMII interface found in device tree\n");
+		return 0;
+	} else if (fdt_port_node < 0) {
+		debug("%s: Error %d parsing device tree\n", __func__,
+		      fdt_port_node);
+		return -1;
+	}
+	port_index = cvmx_fdt_get_int(fdt_addr, fdt_port_node, "reg", -1);
+	if (port_index != 0) {
+		printf("%s: Error: port index (reg) must be 0, not %d.\n",
+		       __func__, port_index);
+		return -1;
+	}
+	reg_addr = cvmx_fdt_get_addr(fdt_addr, fdt_interface_node, "reg");
+	if (reg_addr == FDT_ADDR_T_NONE) {
+		printf("%s: Error: could not get BGX interface address\n",
+		       __func__);
+		return -1;
+	}
+	/* We don't have to bother translating since only 78xx supports OCX and
+	 * doesn't support RGMII.
+	 */
+	xi = __cvmx_bgx_reg_addr_to_xiface(reg_addr);
+	debug("%s: xi.node: %d, xi.interface: 0x%x, addr: 0x%llx\n", __func__,
+	      xi.node, xi.interface, (unsigned long long)reg_addr);
+	if (xi.node < 0) {
+		printf("%s: Device tree BGX node has invalid address 0x%llx\n",
+		       __func__, (unsigned long long)reg_addr);
+		return -1;
+	}
+	debug("%s: Found XCV (RGMII) interface on interface %d\n", __func__,
+	      xi.interface);
+	debug("  phy handle: 0x%x\n",
+	      cvmx_fdt_get_int(fdt_addr, fdt_port_node, "phy-handle", -1));
+	fdt_phy_node =
+		cvmx_fdt_lookup_phandle(fdt_addr, fdt_port_node, "phy-handle");
+	debug("%s: phy-handle node: 0x%x\n", __func__, fdt_phy_node);
+	xiface = cvmx_helper_node_interface_to_xiface(xi.node, xi.interface);
+
+	cvmx_helper_set_port_fdt_node_offset(xiface, port_index, fdt_port_node);
+	if (fdt_phy_node >= 0) {
+		debug("%s: Setting PHY fdt node offset for interface 0x%x, port %d to %d\n",
+		      __func__, xiface, port_index, fdt_phy_node);
+		debug("%s: PHY node name: %s\n", __func__,
+		      fdt_get_name(fdt_addr, fdt_phy_node, NULL));
+		cvmx_helper_set_phy_fdt_node_offset(xiface, port_index,
+						    fdt_phy_node);
+		cvmx_helper_set_port_phy_present(xiface, port_index, true);
+	} else {
+		cvmx_helper_set_phy_fdt_node_offset(xiface, port_index, -1);
+		debug("%s: No PHY fdt node offset for interface 0x%x, port %d to %d\n",
+		      __func__, xiface, port_index, fdt_phy_node);
+		cvmx_helper_set_port_phy_present(xiface, port_index, false);
+	}
+
+	return 0;
+}
+
+/**
+ * Returns if a port is present on an interface
+ *
+ * @param fdt_addr - address fo flat device tree
+ * @param ipd_port - IPD port number
+ *
+ * @return 1 if port is present, 0 if not present, -1 if error
+ */
+int __cvmx_helper_board_get_port_from_dt(void *fdt_addr, int ipd_port)
+{
+	int port_index;
+	int aliases;
+	const char *pip_path;
+	char name_buffer[24];
+	int pip, iface, eth;
+	cvmx_helper_interface_mode_t mode;
+	int xiface = cvmx_helper_get_interface_num(ipd_port);
+	struct cvmx_xiface xi = cvmx_helper_xiface_to_node_interface(xiface);
+	u32 val;
+	int phy_node_offset;
+	int parse_bgx_dt_err;
+	int parse_vsc7224_err;
+
+	debug("%s(%p, %d)\n", __func__, fdt_addr, ipd_port);
+	if (octeon_has_feature(OCTEON_FEATURE_BGX)) {
+		static int fdt_ports_initialized;
+
+		port_index = cvmx_helper_get_interface_index_num(ipd_port);
+
+		if (!fdt_ports_initialized) {
+			if (octeon_has_feature(OCTEON_FEATURE_BGX_XCV)) {
+				if (!__cvmx_helper_parse_bgx_rgmii_dt(fdt_addr))
+					fdt_ports_initialized = 1;
+				parse_bgx_dt_err =
+					__cvmx_helper_parse_bgx_dt(fdt_addr);
+				parse_vsc7224_err =
+					__cvmx_fdt_parse_vsc7224(fdt_addr);
+				if (!parse_bgx_dt_err && !parse_vsc7224_err)
+					fdt_ports_initialized = 1;
+			} else {
+				debug("%s: Error parsing FDT\n", __func__);
+				return -1;
+			}
+		}
+
+		return cvmx_helper_is_port_valid(xiface, port_index);
+	}
+
+	mode = cvmx_helper_interface_get_mode(xiface);
+
+	switch (mode) {
+	/* Device tree has information about the following mode types. */
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_QSGMII:
+	case CVMX_HELPER_INTERFACE_MODE_RXAUI:
+	case CVMX_HELPER_INTERFACE_MODE_AGL:
+	case CVMX_HELPER_INTERFACE_MODE_XLAUI:
+	case CVMX_HELPER_INTERFACE_MODE_XFI:
+		aliases = 1;
+		break;
+	default:
+		aliases = 0;
+		break;
+	}
+
+	/* The device tree information is present on interfaces that have phy */
+	if (!aliases)
+		return 1;
+
+	port_index = cvmx_helper_get_interface_index_num(ipd_port);
+
+	aliases = fdt_path_offset(fdt_addr, "/aliases");
+	if (aliases < 0) {
+		debug("%s: ERROR: /aliases not found in device tree fdt_addr=%p\n",
+		      __func__, fdt_addr);
+		return -1;
+	}
+
+	pip_path = (const char *)fdt_getprop(fdt_addr, aliases, "pip", NULL);
+	if (!pip_path) {
+		debug("%s: ERROR: interface %x pip path not found in device tree\n",
+		      __func__, xiface);
+		return -1;
+	}
+	pip = fdt_path_offset(fdt_addr, pip_path);
+	if (pip < 0) {
+		debug("%s: ERROR: interface %x pip not found in device tree\n",
+		      __func__, xiface);
+		return -1;
+	}
+	snprintf(name_buffer, sizeof(name_buffer), "interface@%d",
+		 xi.interface);
+	iface = fdt_subnode_offset(fdt_addr, pip, name_buffer);
+	if (iface < 0)
+		return 0;
+	snprintf(name_buffer, sizeof(name_buffer), "ethernet@%x", port_index);
+	eth = fdt_subnode_offset(fdt_addr, iface, name_buffer);
+	debug("%s: eth subnode offset %d from %s\n", __func__, eth,
+	      name_buffer);
+
+	if (eth < 0)
+		return -1;
+
+	cvmx_helper_set_port_fdt_node_offset(xiface, port_index, eth);
+
+	phy_node_offset = cvmx_fdt_get_int(fdt_addr, eth, "phy", -1);
+	cvmx_helper_set_phy_fdt_node_offset(xiface, port_index,
+					    phy_node_offset);
+
+	if (fdt_getprop(fdt_addr, eth, "cavium,sgmii-mac-phy-mode", NULL))
+		cvmx_helper_set_mac_phy_mode(xiface, port_index, true);
+	else
+		cvmx_helper_set_mac_phy_mode(xiface, port_index, false);
+
+	if (fdt_getprop(fdt_addr, eth, "cavium,force-link-up", NULL))
+		cvmx_helper_set_port_force_link_up(xiface, port_index, true);
+	else
+		cvmx_helper_set_port_force_link_up(xiface, port_index, false);
+
+	if (fdt_getprop(fdt_addr, eth, "cavium,sgmii-mac-1000x-mode", NULL))
+		cvmx_helper_set_1000x_mode(xiface, port_index, true);
+	else
+		cvmx_helper_set_1000x_mode(xiface, port_index, false);
+
+	if (fdt_getprop(fdt_addr, eth, "cavium,disable-autonegotiation", NULL))
+		cvmx_helper_set_port_autonegotiation(xiface, port_index, false);
+	else
+		cvmx_helper_set_port_autonegotiation(xiface, port_index, true);
+
+	if (mode == CVMX_HELPER_INTERFACE_MODE_AGL) {
+		bool tx_bypass = false;
+
+		if (fdt_getprop(fdt_addr, eth, "cavium,rx-clk-delay-bypass",
+				NULL))
+			cvmx_helper_set_agl_rx_clock_delay_bypass(
+				xiface, port_index, true);
+		else
+			cvmx_helper_set_agl_rx_clock_delay_bypass(
+				xiface, port_index, false);
+
+		val = cvmx_fdt_get_int(fdt_addr, eth, "cavium,rx-clk-skew", 0);
+		cvmx_helper_set_agl_rx_clock_skew(xiface, port_index, val);
+
+		if (fdt_getprop(fdt_addr, eth, "cavium,tx-clk-delay-bypass",
+				NULL))
+			tx_bypass = true;
+
+		val = cvmx_fdt_get_int(fdt_addr, eth, "tx-clk-delay", 0);
+		cvmx_helper_cfg_set_rgmii_tx_clk_delay(xiface, port_index,
+						       tx_bypass, val);
+
+		val = cvmx_fdt_get_int(fdt_addr, eth, "cavium,refclk-sel", 0);
+		cvmx_helper_set_agl_refclk_sel(xiface, port_index, val);
+	}
+
+	return (eth >= 0);
+}
+
+/**
+ * Given the address of the MDIO registers, output the CPU node and MDIO bus
+ *
+ * @param	addr	64-bit address of MDIO registers (from device tree)
+ * @param[out]	node	CPU node number (78xx)
+ * @param[out]	bus	MDIO bus number
+ */
+void __cvmx_mdio_addr_to_node_bus(u64 addr, int *node, int *bus)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN78XX)) {
+		if (node)
+			*node = cvmx_csr_addr_to_node(addr);
+		addr = cvmx_csr_addr_strip_node(addr);
+	} else {
+		if (node)
+			*node = 0;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX) || OCTEON_IS_MODEL(OCTEON_CN78XX)) {
+		switch (addr) {
+		case 0x0001180000003800:
+			*bus = 0;
+			break;
+		case 0x0001180000003880:
+			*bus = 1;
+			break;
+		case 0x0001180000003900:
+			*bus = 2;
+			break;
+		case 0x0001180000003980:
+			*bus = 3;
+			break;
+		default:
+			*bus = -1;
+			printf("%s: Invalid SMI bus address 0x%llx\n", __func__,
+			       (unsigned long long)addr);
+			break;
+		}
+	} else if (OCTEON_IS_MODEL(OCTEON_CN73XX) ||
+		   OCTEON_IS_MODEL(OCTEON_CNF75XX)) {
+		switch (addr) {
+		case 0x0001180000003800:
+			*bus = 0;
+			break;
+		case 0x0001180000003880:
+			*bus = 1;
+			break;
+		default:
+			*bus = -1;
+			printf("%s: Invalid SMI bus address 0x%llx\n", __func__,
+			       (unsigned long long)addr);
+			break;
+		}
+	} else {
+		switch (addr) {
+		case 0x0001180000001800:
+			*bus = 0;
+			break;
+		case 0x0001180000001900:
+			*bus = 1;
+			break;
+		default:
+			*bus = -1;
+			printf("%s: Invalid SMI bus address 0x%llx\n", __func__,
+			       (unsigned long long)addr);
+			break;
+		}
+	}
+}
+
+/**
+ * @INTERNAL
+ * Figure out which mod_abs changed function to use based on the phy type
+ *
+ * @param	xiface	xinterface number
+ * @param	index	port index on interface
+ *
+ * @return	0 for success, -1 on error
+ *
+ * This function figures out the proper mod_abs_changed function to use and
+ * registers the appropriate function.  This should be called after the device
+ * tree has been fully parsed for the given port as well as after all SFP
+ * slots and any Microsemi VSC7224 devices have been parsed in the device tree.
+ */
+int cvmx_helper_phy_register_mod_abs_changed(int xiface, int index)
+{
+	struct cvmx_vsc7224_chan *vsc7224_chan;
+	struct cvmx_fdt_sfp_info *sfp_info;
+
+	debug("%s(0x%x, %d)\n", __func__, xiface, index);
+	sfp_info = cvmx_helper_cfg_get_sfp_info(xiface, index);
+	/* Don't return an error if no SFP module is registered */
+	if (!sfp_info) {
+		debug("%s: No SFP associated with 0x%x:%d\n", __func__, xiface,
+		      index);
+		return 0;
+	}
+
+	/* See if the Microsemi VSC7224 reclocking chip has been used */
+	vsc7224_chan = cvmx_helper_cfg_get_vsc7224_chan_info(xiface, index);
+	if (vsc7224_chan) {
+		debug("%s: Registering VSC7224 handler\n", __func__);
+		cvmx_sfp_register_mod_abs_changed(sfp_info,
+						  &cvmx_sfp_vsc7224_mod_abs_changed, NULL);
+		return 0;
+	}
+
+	return 0;
+}
-- 
2.35.1



More information about the U-Boot mailing list