[PATCH 3/8] spi: aspeed: Add ASPEED SPI controller driver
Chin-Ting Kuo
chin-ting_kuo at aspeedtech.com
Wed May 4 05:47:15 CEST 2022
Hi Jagan,
> -----Original Message-----
> From: Jagan Teki <jagan at amarulasolutions.com>
> Sent: Tuesday, May 3, 2022 9:23 PM
> To: Chin-Ting Kuo <chin-ting_kuo at aspeedtech.com>
> Subject: Re: [PATCH 3/8] spi: aspeed: Add ASPEED SPI controller driver
>
> On Tue, May 3, 2022 at 6:44 PM Chin-Ting Kuo
> <chin-ting_kuo at aspeedtech.com> wrote:
> >
> > Hi Jagan,
> >
> > Thanks for the review.
> >
> > > -----Original Message-----
> > > From: Jagan Teki <jagan at amarulasolutions.com>
> > > Sent: Tuesday, May 3, 2022 8:32 PM
> > > To: Chin-Ting Kuo <chin-ting_kuo at aspeedtech.com>
> > > Subject: Re: [PATCH 3/8] spi: aspeed: Add ASPEED SPI controller
> > > driver
> > >
> > > On Thu, Apr 14, 2022 at 4:54 PM Chin-Ting Kuo
> > > <chin-ting_kuo at aspeedtech.com> wrote:
> > > >
> > > > Add ASPEED BMC FMC/SPI memory controller driver with spi-mem
> > > > interface for AST2500 and AST2600 platform.
> > > >
> > > > There are three SPI memory controllers embedded in an ASPEED SoC.
> > > > - FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
> > > > fetches initial device boot image from FMC chip select(CS) 0.
> > > >
> > > > - SPI1: Play the role of a SPI Master controller. Or, there is a
> > > > dedicated path for HOST(X86) to access its BIOS flash mounted
> > > > under BMC. spi-aspeed.c implements the control sequence
> when
> > > > SPI1 is a SPI master.
> > > >
> > > > - SPI2: It is a pure SPI flash controller. For most scenarios, flashes
> > > > mounted under it are for pure storage purpose.
> > > >
> > > > ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
> > > > Three types of command mode are supported, normal mode, command
> > > > read/write mode and user mode.
> > > > - Normal mode: Default mode. After power on, normal read command
> > > > 03h
> > > or
> > > > 13h is used to fetch boot image from SPI flash.
> > > > - AST2500: Only 03h command can be used after
> power
> > > on
> > > > or reset.
> > > > - AST2600: If FMC04[6:4] is set, 13h command is used,
> > > > otherwise, 03h command.
> > > > The address length is decided by FMC04[2:0].
> > > >
> > > > - Command mode: SPI controller can send command and address
> > > > automatically when CPU read/write the related
> > > remapped
> > > > or decoded address area. The command used by this
> > > mode
> > > > can be configured by FMC10/14/18[23:16]. Also, the
> > > > address length is decided by FMC04[2:0]. This mode
> will
> > > > be implemented in the following patch series.
> > > >
> > > > - User mode: It is a traditional and pure SPI operation, where
> > > > SPI transmission is controlled by CPU. It is the main
> > > > mode in this patch.
> > > >
> > > > Each SPI controller in ASPEED SoC has its own decoded address mapping.
> > > > Within each SPI controller decoded address, driver can assign a
> > > > specific address region for each CS of a SPI controller. The
> > > > decoded address cannot overlap to each other. With normal mode and
> > > > command mode, the decoded address accessed by the CPU determines
> > > > which CS is
> > > active.
> > > > When user mode is adopted, the CS decoded address is a FIFO, CPU
> > > > can send/receive any SPI transmission by accessing the related
> > > > decoded address for the target CS.
> > > >
> > > > Signed-off-by: Chin-Ting Kuo <chin-ting_kuo at aspeedtech.com>
> > > > ---
> > > > configs/evb-ast2500_defconfig | 13 +
> > > > configs/evb-ast2600_defconfig
> > > > | 13 +
> > > > drivers/spi/Kconfig | 8 +
> > > > drivers/spi/Makefile | 1 +
> > > > drivers/spi/spi-aspeed.c | 822
> > > ++++++++++++++++++++++++++++++++++
> > > > 5 files changed, 857 insertions(+) create mode 100644
> > > > drivers/spi/spi-aspeed.c
> > > >
> > > > diff --git a/configs/evb-ast2500_defconfig
> > > > b/configs/evb-ast2500_defconfig index 53fe7776e9..f00bded237
> > > > 100644
> > > > --- a/configs/evb-ast2500_defconfig
> > > > +++ b/configs/evb-ast2500_defconfig
> > > > @@ -36,6 +36,16 @@ CONFIG_DM_I2C=y CONFIG_SYS_I2C_ASPEED=y
> > > > CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ASPEED=y
> > > > +CONFIG_DM_SPI_FLASH=y
> > > > +CONFIG_SPI_FLASH_SFDP_SUPPORT=y
> > > > +CONFIG_SPI_FLASH_GIGADEVICE=y
> > > > +CONFIG_SPI_FLASH_ISSI=y
> > > > +CONFIG_SPI_FLASH_MACRONIX=y
> > > > +CONFIG_SPI_FLASH_SPANSION=y
> > > > +CONFIG_SPI_FLASH_STMICRO=y
> > > > +CONFIG_SPI_FLASH_SST=y
> > > > +CONFIG_SPI_FLASH_WINBOND=y
> > > > +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> > > > CONFIG_PHY_REALTEK=y
> > > > CONFIG_DM_ETH=y
> > > > CONFIG_FTGMAC100=y
> > > > @@ -45,6 +55,9 @@ CONFIG_RAM=y
> > > > CONFIG_DM_RESET=y
> > > > CONFIG_DM_SERIAL=y
> > > > CONFIG_SYS_NS16550=y
> > > > +CONFIG_SPI=y
> > > > +CONFIG_DM_SPI=y
> > > > +CONFIG_SPI_ASPEED=y
> > > > CONFIG_SYSRESET=y
> > > > CONFIG_TIMER=y
> > > > CONFIG_WDT=y
> > > > diff --git a/configs/evb-ast2600_defconfig
> > > > b/configs/evb-ast2600_defconfig index ea75762926..e013976bb0
> > > > 100644
> > > > --- a/configs/evb-ast2600_defconfig
> > > > +++ b/configs/evb-ast2600_defconfig
> > > > @@ -66,6 +66,16 @@ CONFIG_MISC=y
> > > > CONFIG_SPL_MISC=y
> > > > CONFIG_MMC_SDHCI=y
> > > > CONFIG_MMC_SDHCI_ASPEED=y
> > > > +CONFIG_DM_SPI_FLASH=y
> > > > +CONFIG_SPI_FLASH_SFDP_SUPPORT=y
> > > > +CONFIG_SPI_FLASH_GIGADEVICE=y
> > > > +CONFIG_SPI_FLASH_ISSI=y
> > > > +CONFIG_SPI_FLASH_MACRONIX=y
> > > > +CONFIG_SPI_FLASH_SPANSION=y
> > > > +CONFIG_SPI_FLASH_STMICRO=y
> > > > +CONFIG_SPI_FLASH_SST=y
> > > > +CONFIG_SPI_FLASH_WINBOND=y
> > > > +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> > > > CONFIG_PHY_REALTEK=y
> > > > CONFIG_DM_ETH=y
> > > > CONFIG_DM_MDIO=y
> > > > @@ -78,6 +88,9 @@ CONFIG_SPL_RAM=y CONFIG_DM_RESET=y
> > > > CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y
> > > > +CONFIG_SPI=y
> > > > +CONFIG_DM_SPI=y
> > > > +CONFIG_SPI_ASPEED=y
> > > > CONFIG_SYSRESET=y
> > > > CONFIG_SPL_SYSRESET=y
> > > > CONFIG_WDT=y
> > >
> > > Separate patches for spi driver and config enablements.
> >
> > Do you mean that the following change should be separated into a new
> standalone patch?
> > If yes, maybe, I also need to move the remaining changes of this config file to
> the other new patch.
> > +CONFIG_SPI_ASPEED=y
>
> SPI driver has to be a separate patch as it goes to spi tree. also, other patches
> in this series are not part of spi so send them to respective maintainers.
Okay, this will be updated in the next version.
Chin-Ting
> Jagan.
More information about the U-Boot
mailing list