[PATCH 2/8] ARM: dts: imx: Migrate iMX6QDL DRC02 DTs from Linux
Philip Oberfichtner
pro at denx.de
Thu May 19 13:08:31 CEST 2022
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex at denx.de>
Signed-off-by: Philip Oberfichtner <pro at denx.de>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6qdl-dhcom-drc02.dtsi | 143 ++++++++++++++++++++++++++
arch/arm/dts/imx6s-dhcom-drc02.dts | 30 ++++++
configs/dh_imx6_defconfig | 2 +-
4 files changed, 175 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/imx6qdl-dhcom-drc02.dtsi
create mode 100644 arch/arm/dts/imx6s-dhcom-drc02.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 83630af4f6..7bfdfb5313 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -771,6 +771,7 @@ dtb-y += \
imx6dl-sabreauto.dtb \
imx6dl-sabresd.dtb \
imx6dl-wandboard-revd1.dtb \
+ imx6s-dhcom-drc02.dtb
endif
diff --git a/arch/arm/dts/imx6qdl-dhcom-drc02.dtsi b/arch/arm/dts/imx6qdl-dhcom-drc02.dtsi
new file mode 100644
index 0000000000..702cd4a1b2
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-dhcom-drc02.dtsi
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ */
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+/*
+ * Special SoM hardware required which uses the pins from micro SD card. The
+ * pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
+ * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD
+ * card must be disabled and the uart1 rts/cts must be output on other DHCOM
+ * pins, see uart1 and usdhc3 node below.
+ */
+&can2 {
+ status = "okay";
+};
+
+&gpio1 {
+ /*
+ * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+ * GPIO line, however the i.MX6 UART driver assumes RX happens
+ * during TX anyway and that it only controls drive enable DE
+ * line. Hence, the RX is always enabled here.
+ */
+ rs485-rx-en-hog {
+ gpio-hog;
+ gpios = <18 0>; /* GPIO Q */
+ line-name = "rs485-rx-en";
+ output-low;
+ };
+};
+
+&gpio3 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "DRC02-In1", "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "", "", "DHCOM-E", "DRC02-In2", "DHCOM-H",
+ "DHCOM-I", "DRC02-HW0", "", "", "", "", "", "",
+ "", "", "", "", "DRC02-Out1", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio6 {
+ gpio-line-names =
+ "", "", "", "DRC02-Out2", "", "", "SOM-HW1", "",
+ "", "", "", "", "", "", "DRC02-HW2", "DRC02-HW1",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+ eeprom at 50 {
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&uart1 {
+ /*
+ * Due to the use of can2 the signals for can2 Tx and Rx are routed to
+ * DHCOM UART1 rts/cts pins. Therefore this UART have to use DHCOM GPIOs
+ * for rts/cts. So configure DHCOM GPIO I as rts and GPIO M as cts.
+ */
+ /delete-property/ uart-has-rtscts;
+ cts-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; /* GPIO M */
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_dhcom_i &pinctrl_dhcom_m>;
+ pinctrl-names = "default";
+ rts-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&uart5 {
+ /*
+ * On DRC02 this UART is used as RS485 interface and RS485_TX_En is
+ * controlled by DHCOM GPIO P. So remove rts/cts pins and the property
+ * uart-has-rtscts from this UART and add the DHCOM GPIO P pin via
+ * rts-gpios. The RS485_RX_En is controlled by DHCOM GPIO Q, see gpio1
+ * node above.
+ */
+ /delete-property/ uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ pinctrl-0 = <&pinctrl_uart5_core &pinctrl_dhcom_p &pinctrl_dhcom_q>;
+ pinctrl-names = "default";
+ rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */
+};
+
+&usbh1 {
+ disable-over-current;
+};
+
+&usdhc2 { /* SD card */
+ status = "okay";
+};
+
+&usdhc3 {
+ /*
+ * Due to the use of can2 the micro SD card on module have to be
+ * disabled, because the pins SD3_DAT0 and SD3_DAT1 are muxed as
+ * can2 Tx and Rx.
+ */
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl-0 = <
+ /*
+ * The following DHCOM GPIOs are used on this board.
+ * Therefore, they have been removed from the list below.
+ * I: uart1 rts
+ * M: uart1 cts
+ * P: uart5 rs485-tx-en
+ * Q: uart5 rs485-rx-en
+ */
+ &pinctrl_hog_base
+ &pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
+ &pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
+ &pinctrl_dhcom_g &pinctrl_dhcom_h
+ &pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
+ &pinctrl_dhcom_n &pinctrl_dhcom_o
+ &pinctrl_dhcom_r
+ &pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
+ &pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
+ >;
+ pinctrl-names = "default";
+
+ pinctrl_uart5_core: uart5-core-grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6s-dhcom-drc02.dts b/arch/arm/dts/imx6s-dhcom-drc02.dts
new file mode 100644
index 0000000000..4077b607c2
--- /dev/null
+++ b/arch/arm/dts/imx6s-dhcom-drc02.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 DH electronics GmbH
+ *
+ * DHCOM iMX6 variant:
+ * DHCM-iMX6S-C0800-R102-F0409-E-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 493-400 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+/*
+ * The kernel only distinguishes between i.MX6 Quad and DualLite,
+ * but the Solo is actually a DualLite with only one CPU. So use
+ * DualLite for the Solo and disable one CPU node.
+ */
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-dhcom-som.dtsi"
+#include "imx6qdl-dhcom-drc02.dtsi"
+
+/ {
+ model = "DH electronics i.MX6S DHCOM on DRC02";
+ compatible = "dh,imx6s-dhcom-drc02", "dh,imx6s-dhcom-som",
+ "fsl,imx6dl";
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+};
diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig
index c45561aa0e..9c78987473 100644
--- a/configs/dh_imx6_defconfig
+++ b/configs/dh_imx6_defconfig
@@ -53,7 +53,7 @@ CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_OF_CONTROL=y
-CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2"
+CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2 imx6s-dhcom-drc02"
CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
--
2.34.1
More information about the U-Boot
mailing list