[PATCH 2/2] arm: mvebu: add support for Methode eDPU
Robert Marko
robert.marko at sartura.hr
Fri May 20 12:55:41 CEST 2022
On Mon, May 16, 2022 at 10:54 AM Stefan Roese <sr at denx.de> wrote:
>
> On 16.05.22 10:52, Robert Marko wrote:
> > On Mon, May 16, 2022 at 8:40 AM Stefan Roese <sr at denx.de> wrote:
> >>
> >> On 06.05.22 20:01, Robert Marko wrote:
> >>> Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
> >>>
> >>> They feature the same CPU, RAM, and storage as well as the form factor.
> >>>
> >>> However, eDPU only has one SFP slot plus a copper G.hn port which does not
> >>> work under U-boot.
> >>>
> >>> In order to reduce duplication, split the uDPU DTS into a common one.
> >>>
> >>> Signed-off-by: Robert Marko <robert.marko at sartura.hr>
> >>
> >> Reviewed-by: Stefan Roese <sr at denx.de>
> >
> > Hi Stefan,
> > Can you hold off on merging this until v2?
> >
> > I have a few more comments to take care in Linux upstreaming
> > and will then use the final DTS versions in v2.
> > Had to convert A37xx bindings to YAML, so that slowed everything down.
>
> Sure. Thanks for the notice. Please make sure though, that you add the
> new board to some MAINTAINERS file. As this throws an CI build error
> without this.
Hi, thanks for the heads up on MAINTAINERS.
Sent the v3 with sync to the Linux pending DTS and MAINTAINERS added.
Regards,
Robert
>
> Thanks,
> Stefan
>
> > Regards,
> > Robert
> >>
> >> Thanks,
> >> Stefan
> >>
> >>> ---
> >>> arch/arm/dts/armada-3720-eDPU-u-boot.dtsi | 45 ++++++
> >>> arch/arm/dts/armada-3720-eDPU.dts | 14 ++
> >>> arch/arm/dts/armada-3720-uDPU.dts | 153 +-------------------
> >>> arch/arm/dts/armada-3720-uDPU.dtsi | 163 ++++++++++++++++++++++
> >>> configs/eDPU_defconfig | 99 +++++++++++++
> >>> 5 files changed, 322 insertions(+), 152 deletions(-)
> >>> create mode 100644 arch/arm/dts/armada-3720-eDPU-u-boot.dtsi
> >>> create mode 100644 arch/arm/dts/armada-3720-eDPU.dts
> >>> create mode 100644 arch/arm/dts/armada-3720-uDPU.dtsi
> >>> create mode 100644 configs/eDPU_defconfig
> >>>
> >>> diff --git a/arch/arm/dts/armada-3720-eDPU-u-boot.dtsi b/arch/arm/dts/armada-3720-eDPU-u-boot.dtsi
> >>> new file mode 100644
> >>> index 0000000000..1b2648f64d
> >>> --- /dev/null
> >>> +++ b/arch/arm/dts/armada-3720-eDPU-u-boot.dtsi
> >>> @@ -0,0 +1,45 @@
> >>> +// SPDX-License-Identifier: GPL-2.0+
> >>> +
> >>> +/ {
> >>> + smbios {
> >>> + compatible = "u-boot,sysinfo-smbios";
> >>> +
> >>> + smbios {
> >>> + system {
> >>> + product = "eDPU";
> >>> + };
> >>> +
> >>> + baseboard {
> >>> + product = "eDPU";
> >>> + };
> >>> +
> >>> + chassis {
> >>> + product = "eDPU";
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&spi0 {
> >>> + u-boot,dm-pre-reloc;
> >>> +
> >>> + spi-flash at 0 {
> >>> + u-boot,dm-pre-reloc;
> >>> + };
> >>> +};
> >>> +
> >>> +&sdhci0 {
> >>> + u-boot,dm-pre-reloc;
> >>> +};
> >>> +
> >>> +ð0 {
> >>> + /* G.hn does not work without additional configuration */
> >>> + status = "disabled";
> >>> +};
> >>> +
> >>> +ð1 {
> >>> + fixed-link {
> >>> + speed = <1000>;
> >>> + full-duplex;
> >>> + };
> >>> +};
> >>> diff --git a/arch/arm/dts/armada-3720-eDPU.dts b/arch/arm/dts/armada-3720-eDPU.dts
> >>> new file mode 100644
> >>> index 0000000000..f2e2d21a8d
> >>> --- /dev/null
> >>> +++ b/arch/arm/dts/armada-3720-eDPU.dts
> >>> @@ -0,0 +1,14 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include "armada-3720-uDPU.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Methode eDPU Board";
> >>> + compatible = "methode,edpu", "marvell,armada3720";
> >>> +};
> >>> +
> >>> +ð0 {
> >>> + phy-mode = "1000base-x";
> >>> +};
> >>> diff --git a/arch/arm/dts/armada-3720-uDPU.dts b/arch/arm/dts/armada-3720-uDPU.dts
> >>> index 1f534c0c65..b146fae9f6 100644
> >>> --- a/arch/arm/dts/armada-3720-uDPU.dts
> >>> +++ b/arch/arm/dts/armada-3720-uDPU.dts
> >>> @@ -1,67 +1,13 @@
> >>> // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>> -/*
> >>> - * Device tree for the uDPU board.
> >>> - * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
> >>> - * Copyright (C) 2016 Marvell
> >>> - * Copyright (C) 2019 Methode Electronics
> >>> - * Copyright (C) 2019 Telus
> >>> - *
> >>> - * Vladimir Vid <vladimir.vid at sartura.hr>
> >>> - */
> >>>
> >>> /dts-v1/;
> >>>
> >>> -#include <dt-bindings/gpio/gpio.h>
> >>> -#include "armada-372x.dtsi"
> >>> +#include "armada-3720-uDPU.dtsi"
> >>>
> >>> / {
> >>> model = "Methode uDPU Board";
> >>> compatible = "methode,udpu", "marvell,armada3720";
> >>>
> >>> - chosen {
> >>> - stdout-path = "serial0:115200n8";
> >>> - };
> >>> -
> >>> - memory at 0 {
> >>> - device_type = "memory";
> >>> - reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> >>> - };
> >>> -
> >>> - leds {
> >>> - pinctrl-names = "default";
> >>> - compatible = "gpio-leds";
> >>> -
> >>> - power1 {
> >>> - label = "udpu:green:power";
> >>> - gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> -
> >>> - power2 {
> >>> - label = "udpu:red:power";
> >>> - gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> -
> >>> - network1 {
> >>> - label = "udpu:green:network";
> >>> - gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> -
> >>> - network2 {
> >>> - label = "udpu:red:network";
> >>> - gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> -
> >>> - alarm1 {
> >>> - label = "udpu:green:alarm";
> >>> - gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> -
> >>> - alarm2 {
> >>> - label = "udpu:red:alarm";
> >>> - gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
> >>> - };
> >>> - };
> >>> -
> >>> sfp_eth0: sfp-eth0 {
> >>> compatible = "sff,sfp";
> >>> i2c-bus = <&i2c0>;
> >>> @@ -71,55 +17,6 @@
> >>> tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
> >>> maximum-power-milliwatt = <3000>;
> >>> };
> >>> -
> >>> - sfp_eth1: sfp-eth1 {
> >>> - compatible = "sff,sfp";
> >>> - i2c-bus = <&i2c1>;
> >>> - los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
> >>> - mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
> >>> - tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
> >>> - tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
> >>> - maximum-power-milliwatt = <3000>;
> >>> - };
> >>> -};
> >>> -
> >>> -&sdhci0 {
> >>> - status = "okay";
> >>> - bus-width = <8>;
> >>> - mmc-ddr-1_8v;
> >>> - mmc-hs400-1_8v;
> >>> - marvell,pad-type = "fixed-1-8v";
> >>> - non-removable;
> >>> - no-sd;
> >>> - no-sdio;
> >>> -};
> >>> -
> >>> -&spi0 {
> >>> - status = "okay";
> >>> - pinctrl-names = "default";
> >>> - pinctrl-0 = <&spi_quad_pins>;
> >>> -
> >>> - spi-flash at 0 {
> >>> - compatible = "jedec,spi-nor";
> >>> - reg = <0>;
> >>> - spi-max-frequency = <54000000>;
> >>> -
> >>> - partitions {
> >>> - compatible = "fixed-partitions";
> >>> - #address-cells = <1>;
> >>> - #size-cells = <1>;
> >>> -
> >>> - partition at 0 {
> >>> - label = "firmware";
> >>> - reg = <0x0 0x180000>;
> >>> - };
> >>> -
> >>> - partition at 180000 {
> >>> - label = "u-boot-env";
> >>> - reg = <0x180000 0x10000>;
> >>> - };
> >>> - };
> >>> - };
> >>> };
> >>>
> >>> &pinctrl_nb {
> >>> @@ -127,11 +24,6 @@
> >>> groups = "i2c1";
> >>> function = "gpio";
> >>> };
> >>> -
> >>> - i2c2_recovery_pins: i2c2-recovery-pins {
> >>> - groups = "i2c2";
> >>> - function = "gpio";
> >>> - };
> >>> };
> >>>
> >>> &i2c0 {
> >>> @@ -144,50 +36,7 @@
> >>> sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >>> };
> >>>
> >>> -&i2c1 {
> >>> - status = "okay";
> >>> - pinctrl-names = "default", "recovery";
> >>> - pinctrl-0 = <&i2c2_pins>;
> >>> - pinctrl-1 = <&i2c2_recovery_pins>;
> >>> - /delete-property/mrvl,i2c-fast-mode;
> >>> - scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >>> - sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >>> -
> >>> - nct375 at 48 {
> >>> - status = "okay";
> >>> - compatible = "ti,tmp75c";
> >>> - reg = <0x48>;
> >>> - };
> >>> -
> >>> - nct375 at 49 {
> >>> - status = "okay";
> >>> - compatible = "ti,tmp75c";
> >>> - reg = <0x49>;
> >>> - };
> >>> -};
> >>> -
> >>> ð0 {
> >>> phy-mode = "sgmii";
> >>> - status = "okay";
> >>> - managed = "in-band-status";
> >>> - phys = <&comphy1 0>;
> >>> sfp = <&sfp_eth0>;
> >>> };
> >>> -
> >>> -ð1 {
> >>> - phy-mode = "sgmii";
> >>> - status = "okay";
> >>> - managed = "in-band-status";
> >>> - phys = <&comphy0 1>;
> >>> - sfp = <&sfp_eth1>;
> >>> -};
> >>> -
> >>> -&usb3 {
> >>> - status = "okay";
> >>> - phys = <&usb2_utmi_otg_phy>;
> >>> - phy-names = "usb2-utmi-otg-phy";
> >>> -};
> >>> -
> >>> -&uart0 {
> >>> - status = "okay";
> >>> -};
> >>> diff --git a/arch/arm/dts/armada-3720-uDPU.dtsi b/arch/arm/dts/armada-3720-uDPU.dtsi
> >>> new file mode 100644
> >>> index 0000000000..5e38acc92a
> >>> --- /dev/null
> >>> +++ b/arch/arm/dts/armada-3720-uDPU.dtsi
> >>> @@ -0,0 +1,163 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>> +/*
> >>> + * Device tree for the uDPU board.
> >>> + * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
> >>> + * Copyright (C) 2016 Marvell
> >>> + * Copyright (C) 2019 Methode Electronics
> >>> + * Copyright (C) 2019 Telus
> >>> + *
> >>> + * Vladimir Vid <vladimir.vid at sartura.hr>
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include "armada-372x.dtsi"
> >>> +
> >>> +/ {
> >>> + chosen {
> >>> + stdout-path = "serial0:115200n8";
> >>> + };
> >>> +
> >>> + memory at 0 {
> >>> + device_type = "memory";
> >>> + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> >>> + };
> >>> +
> >>> + leds {
> >>> + pinctrl-names = "default";
> >>> + compatible = "gpio-leds";
> >>> +
> >>> + power1 {
> >>> + label = "udpu:green:power";
> >>> + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> +
> >>> + power2 {
> >>> + label = "udpu:red:power";
> >>> + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> +
> >>> + network1 {
> >>> + label = "udpu:green:network";
> >>> + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> +
> >>> + network2 {
> >>> + label = "udpu:red:network";
> >>> + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> +
> >>> + alarm1 {
> >>> + label = "udpu:green:alarm";
> >>> + gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> +
> >>> + alarm2 {
> >>> + label = "udpu:red:alarm";
> >>> + gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> + };
> >>> +
> >>> + sfp_eth1: sfp-eth1 {
> >>> + compatible = "sff,sfp";
> >>> + i2c-bus = <&i2c1>;
> >>> + los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
> >>> + mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
> >>> + tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
> >>> + tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
> >>> + maximum-power-milliwatt = <3000>;
> >>> + };
> >>> +};
> >>> +
> >>> +&sdhci0 {
> >>> + status = "okay";
> >>> + bus-width = <8>;
> >>> + mmc-ddr-1_8v;
> >>> + mmc-hs400-1_8v;
> >>> + marvell,pad-type = "fixed-1-8v";
> >>> + non-removable;
> >>> + no-sd;
> >>> + no-sdio;
> >>> +};
> >>> +
> >>> +&spi0 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&spi_quad_pins>;
> >>> +
> >>> + spi-flash at 0 {
> >>> + compatible = "jedec,spi-nor";
> >>> + reg = <0>;
> >>> + spi-max-frequency = <54000000>;
> >>> +
> >>> + partitions {
> >>> + compatible = "fixed-partitions";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + /* only bootloader is located on the SPI */
> >>> + partition at 0 {
> >>> + label = "firmware";
> >>> + reg = <0x0 0x180000>;
> >>> + };
> >>> +
> >>> + partition at 180000 {
> >>> + label = "u-boot-env";
> >>> + reg = <0x180000 0x10000>;
> >>> + };
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&pinctrl_nb {
> >>> + i2c2_recovery_pins: i2c2-recovery-pins {
> >>> + groups = "i2c2";
> >>> + function = "gpio";
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c1 {
> >>> + status = "okay";
> >>> + pinctrl-names = "default", "recovery";
> >>> + pinctrl-0 = <&i2c2_pins>;
> >>> + pinctrl-1 = <&i2c2_recovery_pins>;
> >>> + /delete-property/mrvl,i2c-fast-mode;
> >>> + scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >>> + sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >>> +
> >>> + nct375 at 48 {
> >>> + status = "okay";
> >>> + compatible = "ti,tmp75c";
> >>> + reg = <0x48>;
> >>> + };
> >>> +
> >>> + nct375 at 49 {
> >>> + status = "okay";
> >>> + compatible = "ti,tmp75c";
> >>> + reg = <0x49>;
> >>> + };
> >>> +};
> >>> +
> >>> +ð0 {
> >>> + status = "okay";
> >>> + managed = "in-band-status";
> >>> + phys = <&comphy1 0>;
> >>> +};
> >>> +
> >>> +ð1 {
> >>> + phy-mode = "sgmii";
> >>> + status = "okay";
> >>> + managed = "in-band-status";
> >>> + phys = <&comphy0 1>;
> >>> + sfp = <&sfp_eth1>;
> >>> +};
> >>> +
> >>> +&usb3 {
> >>> + status = "okay";
> >>> + phys = <&usb2_utmi_otg_phy>;
> >>> + phy-names = "usb2-utmi-otg-phy";
> >>> +};
> >>> +
> >>> +&uart0 {
> >>> + status = "okay";
> >>> +};
> >>> diff --git a/configs/eDPU_defconfig b/configs/eDPU_defconfig
> >>> new file mode 100644
> >>> index 0000000000..37f91fc4c2
> >>> --- /dev/null
> >>> +++ b/configs/eDPU_defconfig
> >>> @@ -0,0 +1,99 @@
> >>> +CONFIG_ARM=y
> >>> +CONFIG_ARCH_CPU_INIT=y
> >>> +CONFIG_ARCH_MVEBU=y
> >>> +CONFIG_SYS_TEXT_BASE=0x00000000
> >>> +CONFIG_TARGET_MVEBU_ARMADA_37XX=y
> >>> +CONFIG_MVEBU_EFUSE=y
> >>> +CONFIG_ENV_SIZE=0x10000
> >>> +CONFIG_ENV_OFFSET=0x180000
> >>> +CONFIG_ENV_SECT_SIZE=0x10000
> >>> +CONFIG_DM_GPIO=y
> >>> +CONFIG_DEFAULT_DEVICE_TREE="armada-3720-eDPU"
> >>> +CONFIG_DEBUG_UART_BASE=0xd0012000
> >>> +CONFIG_SYS_LOAD_ADDR=0x6000000
> >>> +CONFIG_DEBUG_UART=y
> >>> +CONFIG_AHCI=y
> >>> +CONFIG_DISTRO_DEFAULTS=y
> >>> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> >>> +CONFIG_FIT=y
> >>> +CONFIG_FIT_VERBOSE=y
> >>> +CONFIG_USE_PREBOOT=y
> >>> +# CONFIG_DISPLAY_CPUINFO is not set
> >>> +# CONFIG_DISPLAY_BOARDINFO is not set
> >>> +CONFIG_DISPLAY_BOARDINFO_LATE=y
> >>> +CONFIG_ARCH_EARLY_INIT_R=y
> >>> +CONFIG_BOARD_EARLY_INIT_F=y
> >>> +CONFIG_SYS_PROMPT="uDPU>> "
> >>> +# CONFIG_CMD_ELF is not set
> >>> +# CONFIG_CMD_IMI is not set
> >>> +# CONFIG_CMD_XIMG is not set
> >>> +# CONFIG_CMD_FLASH is not set
> >>> +CONFIG_CMD_FUSE=y
> >>> +CONFIG_CMD_GPIO=y
> >>> +CONFIG_CMD_I2C=y
> >>> +CONFIG_CMD_MMC=y
> >>> +CONFIG_CMD_MTD=y
> >>> +CONFIG_CMD_PCI=y
> >>> +CONFIG_CMD_SPI=y
> >>> +CONFIG_CMD_USB=y
> >>> +# CONFIG_CMD_SETEXPR is not set
> >>> +CONFIG_CMD_TFTPPUT=y
> >>> +CONFIG_CMD_CACHE=y
> >>> +CONFIG_CMD_TIME=y
> >>> +CONFIG_CMD_MVEBU_BUBT=y
> >>> +CONFIG_CMD_EXT4_WRITE=y
> >>> +CONFIG_MAC_PARTITION=y
> >>> +CONFIG_ENV_OVERWRITE=y
> >>> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> >>> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> >>> +CONFIG_ARP_TIMEOUT=200
> >>> +CONFIG_NET_RETRY_COUNT=50
> >>> +CONFIG_NET_RANDOM_ETHADDR=y
> >>> +CONFIG_AHCI_MVEBU=y
> >>> +CONFIG_CLK=y
> >>> +CONFIG_CLK_MVEBU=y
> >>> +CONFIG_DM_I2C=y
> >>> +CONFIG_DM_I2C_GPIO=y
> >>> +CONFIG_SYS_I2C_MV=y
> >>> +CONFIG_MISC=y
> >>> +CONFIG_MMC_HS200_SUPPORT=y
> >>> +CONFIG_MMC_SDHCI=y
> >>> +CONFIG_MMC_SDHCI_SDMA=y
> >>> +CONFIG_MMC_SDHCI_XENON=y
> >>> +CONFIG_MTD=y
> >>> +CONFIG_DM_MTD=y
> >>> +CONFIG_SPI_FLASH_SFDP_SUPPORT=y
> >>> +CONFIG_SPI_FLASH_MACRONIX=y
> >>> +CONFIG_SPI_FLASH_SPANSION=y
> >>> +CONFIG_SPI_FLASH_STMICRO=y
> >>> +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> >>> +CONFIG_SPI_FLASH_MTD=y
> >>> +CONFIG_PHYLIB_10G=y
> >>> +CONFIG_PHY_MARVELL=y
> >>> +CONFIG_PHY_FIXED=y
> >>> +CONFIG_PHY_GIGE=y
> >>> +CONFIG_E1000=y
> >>> +CONFIG_MVNETA=y
> >>> +CONFIG_MVMDIO=y
> >>> +CONFIG_PCI=y
> >>> +CONFIG_PCI_AARDVARK=y
> >>> +CONFIG_PHY=y
> >>> +CONFIG_MVEBU_COMPHY_SUPPORT=y
> >>> +CONFIG_PINCTRL=y
> >>> +CONFIG_PINCTRL_ARMADA_37XX=y
> >>> +CONFIG_DM_REGULATOR_FIXED=y
> >>> +CONFIG_DM_REGULATOR_GPIO=y
> >>> +CONFIG_MVEBU_A3700_UART=y
> >>> +CONFIG_MVEBU_A3700_SPI=y
> >>> +CONFIG_SYSINFO=y
> >>> +CONFIG_SYSINFO_SMBIOS=y
> >>> +CONFIG_USB=y
> >>> +CONFIG_USB_XHCI_HCD=y
> >>> +CONFIG_USB_EHCI_HCD=y
> >>> +CONFIG_USB_HOST_ETHER=y
> >>> +CONFIG_USB_ETHER_ASIX=y
> >>> +CONFIG_USB_ETHER_MCS7830=y
> >>> +CONFIG_USB_ETHER_RTL8152=y
> >>> +CONFIG_USB_ETHER_SMSC95XX=y
> >>> +CONFIG_LZO=y
> >>> +CONFIG_SPL_LZO=y
> >>
> >> Viele Grüße,
> >> Stefan Roese
> >>
> >> --
> >> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> >> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> >> Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
> >
> >
> >
>
> Viele Grüße,
> Stefan Roese
>
> --
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
--
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko at sartura.hr
Web: www.sartura.hr
More information about the U-Boot
mailing list